EZ-BridgeLT-HD ™ High Performance Point to Point Wireless Bridge System ▫ ▫ ▫ ▫ ▫ ▫ Surge protected Ethernet and Power for ultimate reliability. Shielded CAT5 cables to protect against EMI.
DANGER! Avoid Powerlines! You Can Be Killed! When following the instructions in this guide to install the antenna take extreme care to avoid contact with overhead power lines, lights and power circuits. Contact with power lines, lights or power circuits may be fatal. We recommend to install antenna no closer than 20 feet to any power lines. Safety: For your own protection, follow these safety rules.
Qwik Install STEP 1: Choose a mounting location with good line of sight to the remote location. The supplied bracket can be mounted to a wall or to an existing pole up to 2” diameter. If only short distances are needed, the antenna can be mounted inside a building. TECH TIP: Microwaves travel in straight lines and they lose strength quickly when going thru buildings and trees. If there are objects in the microwave path, then useable distance will be reduced.
through the bottom cover and plug into the RJ45 Jack inside the unit. Keep the black gasket material in the bottom of the cover to help keep out dust and insects. STEP 6: Route shielded CAT5 cable from the antenna into the building. Always create a strain relief near the antenna so the cable is not pulling directly on the antenna. Use the CAT5 strain relief hook feature built into the housing back fin. The Ethernet spec allows for a maximum cable length of 100 meters or about 328 feet.
3. SECURITY: Security is pre-configured with system passwords, WPA2 encryption and Mac Address verification pre-set. This is so that you can setup a plug and play link and have confidence that the link is secure and that your data and network are safe. Once you feel comfortable with the system and its operation, we would recommend the following security changes : a.
. SITE SURVEY: The site survey is a very useful tool to determine what wireless devices are within range of your EZ-Bridge™ and could be a source of interference that could cause degraded performance. Go to WIRELESS and then click on SITE SURVEY then REFRESH. The list will show all wireless devices including channel #, MAC Address and relative signal strength of all the devices within the range of the EZBridge™ .
Technical Specifications Standards Certifications Note: Subject to Change Without Notice 2.4GHz 5GHz 802.11b/g 802.11a FCC / CE Radio Specifications Operating Frequency Available Transmit Power (software selectable) 2400 to 2497MHz 4900 to 6000MHz 802.11b 100 to 250mW 802.
Advanced Features The EZ-Bridge™ has many advanced features if more functionality is desired. To access the advanced features, click on Advanced Web at the top of the menu tree. This will activate the advanced menu options. The EZ-Bridge™ can operate as Access Point, Client, WDS, AP+WDS, Point to Point. Go to WIRELESS | BASIC SETTINGS to change wireless mode. Go to ETHERNET | IP SETTINGS to change network operation mode from Bridge (default) to Router.
grounding of the electronics inside the enclosure to prevent damage from electrical storms. Make sure that the POE Power Supply is plugged into a surge protected outlet such as a surge protected power strip or UPS inside the house. Shielded CAT5 cable is also recommended between the POE Inserter and antenna. 5.PAINTING – The EZ-Bridge™ unit can be painted to match a particular house color. Only non metallic enamel or latex paints should be used.
d. Add a high speed link between your home network and a PC in your remote studio or office which is located in an outbuilding on your property. e. Create a secure link for remote video and network based security cameras. The EZ-Bridge™ works with all network based security cameras. f. Create a streaming video conference link between buildings.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Limited Warranty All e-zy.net products are supplied with a limited 12 month warranty which covers material and workmanship defects.
All shipping damage claims are the purchaser's responsibility. Inspect each shipment upon delivery and IMMEDIATELY report all damage, to the carrier. There may be time limits and inspections may be required.
