S450H
CE DECLARATION OF CONFORMITY FOR MACHINES (DIRECTIVE 2006/42/EC) Manufacturer: FAAC S.p.A. Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY Declares that: Operator mod.
S450H ENGLISH 1 1.1 DIMENSIONS DESCRIPTION AND TECHNICAL SPECIFICATIONS The FAAC S450H automated system for swing-leaf gates consists of an electrical pump and an hydraulic piston transmitting the leaf movement, assembled in a single block. The model with hydraulic lock can automate leaves up to 2 m. It does not require the installation of electric locks and guarantees that the leaf is mechanically locked when the motor is not in operation.
If the gate structure does not allow the stable fixing of the front fitting, create a firm bearing surface in the leaf structure. - It is advisable to grease all fixing pins - Opening and closing stops must always be installed - Play special attention not to damage the operator rod 3.2 INSTALLATION DIMENSIONS (Dimensions in millimeters) 3.2.
3.2.2 APPLICATION WITH BRACKET FASTENED TO SIDE WALL ATTENTION: do not cut for any reason the rear bracket Make reference to figures 41 and 51 and to table 2 to determine the installation position of the operator. B1 D1 ENGLISH B1 85 1060 D1 Z Dimensions in millimeters Fig.51 Fig.41 100 Dimensions in millimeters INSTALLATION DIMENSION " B1 " (SEE FIGURE 41-51) B1 TAB.
1. Check the perfect level then weld the rear fitting to the pillar or fix it by means of suitable screws, dowels / threaded inserts. Observe the dimensions stated in Tab.1 (never cut the rear fitting; moreover it must be installed with the word "UP" facing up as shown in figure 6 re. a). 4. 5. Install the encoder on the rear bracket by correctly engaging it on the pin then fix it with the screw and nut supplied (Fig. 8 re. a b c).
15. Secure the operator to the front fixing (Fig. 15). 16. Remove the bleed screw (Fig.16 ref. a) paying special attention to leave the sealing O-Ring in its seat 17. Install the metallic protection cover as shown in Fig. 16, insert and tighten both tie-rods 18. Connect the cable to the operator using the two screws supplied, as shown in Fig. 17. ENGLISH If an external mechanical stop point at closure is present, remove the rod completely and then insert it 5 mm. Fig. 14 Fig. 12 10.
4 MANUAL OPERATION The models S450H SB are not equipped with a release facility since, thanks to the particular configuration of the hydraulic distributing flange, you do not need to release the operator to manually move the leaf ENGLISH If the gate is to be operated manually because of a power failure or an automated system fault, activate the release device. 1) Lift the protection lid (Fig. 18, re. a) and insert the key in the lock (Fig. 18, ref. b).
ENGLISH Fig. 19 LEAF 1* DL 1 DL 2 DL 3 LEAF 2 THROUGH THE BRACKET COVER OF LEAF 2, VERIFY THAT THE LED DL1 IS ON WHEN THE MOTOR IS NOT IN OPERATION THROUGH THE BRACKET COVER OF LEAF 1, VERIFY THAT THE LEDS DL1 AND DL2 ARE ON WHEN THE MOTOR IS NOT IN OPERATION LEAF 1 LEAF 2 TWO LEDS ON ONE LED ON DL 1 DL 2 DL 3 Fig.
6 BLEEDING 1. Loosen the tie-rods (Fig. 23 ref. a) and remove the metal protective housing (Fig. 23 ref. b). b ENGLISH a Remove the upper tie-rod and be careful with the O-ring that must remain it its seat. Fig.23 2. 3. Remove the screw in Fig. 24 ref.d from the front fitting Remove the joint (Fig.24 ref.f) from the operator stem. (Fig. 24 ref. g). TO PREVENT OIL LEAKAGE FROM THE BREATHER HOLE, DO NOT TILT THE OPERATOR DOWNWARD d Fig.26 g 5.
Le descrizioni e le illustrazioni del presente manuale non sono impegnative. La FAAC si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale. The descriptions and illustrations contained in the present manual are not binding.
