Installation instructions

Version 07/11 - Page 7
.
ATTACH THE SUPPORT
4. Determine and make necessary cuts for the ductwork. The duct
opening is shown on the mounting template (L in FIGURE 7). Install
ductwork before mounting the support.
FIGURE 9
FIGURE 7
Ductless installations require
a Ductless Conversion
Kit whose components are
pictured in FIGURE 10. Do
not use the DAMPER (N
in FIGURE 1) for ductless
installations. The LOWER
CHIMNEY COVER (B in
FIGURE 1) should be
discarded and replaced by
the new one with holes from
the Ductless Conversion Kit
(D in FIGURE 10).
As indicated in FIGURE
10, place the DUCTLESS
DIVERTER (A) over the
exhaust opening of the EASY
(E). Fit the DUCTLESS
 
 (B) into the
DIVERTER (A).
FIGURE 10
FIGURE 11
MAKE THE ELECTRICAL CONNECTION
DO NOT
turn on the power until installation is complete! Connect
the Power Supply Cable to the rangehood. Attach the White
lead of the power supply to the White lead of the rangehood


twist-on type wire connector. Connect the Green (Green and
Yellow) ground wire under the Green grounding screw.
1. Put a thick, protective
covering over cooktop,
set-in range or countertop
to protect from damage
or dirt.
2. Determine and clearly
mark with a pencil on
t h e c e i l i n g w h e r e
the rangehood will be
installed.
3. A template (L in FIGURE
7) for mounting the support
is supplied in the carton
with the support. Use this
template to mark holes for
support on the ceiling.
FOR DUCTLESS INSTALLATIONS
1. The UPPER CHIMNEY
COVER (C in FIGURE 11)
attaches using two screws
provided (G in FIGURE 11).
If using the High Ceiling
Chimney Kit, use the
UPPER CHIMNEY COVER
supplied with the kit. Slide
up and attach the UPPER
CHIMNEY COVER.
2. Attach the duct work to
the DAMPER (M in FIGURE
1). Make sure to seal all
joints with duct tape to
prevent leaks.
3. The LOWER CHIMNEY
COVER (B in FIGURE
11) attaches using two
screws provided (G in
FIGURE 11). Install the
LOWER CHIMNEY COVER
by sliding it up over the
support and the UPPER
CHIMNEY COVER.
For ductless installations, line up the DUCTLESS DIVERTER
(B in FIGURE 10) with the holes
in the LOWER CHIMNEY COVER (D in FIGURE 10) and snap
in the VENT GRIDS (C in FIGURE 10).
INSTALLING THE RANGEHOOD
8. Attach the CHIMNEY SUPPORT (D in FIGURE 9) to the ceiling.

the desired length of the support structure and adjust the length of the
support by removing the four screws (indicated in FIGURE 9) with a

install and tighten the four screws.
6. Determine the proper location for the Power Supply Cable as

Run the Power Supply Cable. Use caulking to seal around the
hole. DO NOT turn on the power until installation is complete!
A knockout is provided at the top of the CHIMNEY SUPPORT (D
in FIGURE 9).
7. For ducted installations, place the round DAMPER (N in FIGURE
1) into the exhaust opening of the rangehood and press down.
5. If using the High Ceiling
Chimney Kit, remove
the CHIMNEY COVER
from the CHIMNEY
 (A in
FIGURE 8). Position the
 
over the CHIMNEY
SUPPORT (B in FIGURE
8) so that the outside
edges and the electrical
holes line up. Attach the

the CHIMNEY SUPPORT
using the 4 bolts (C in
FIGURE 8). Tighten bolts
securely.
FIGURE 8