User manual

BEFORE USING THE WRENCH
BATTERY INSTALLATION B
•
Remove the battery cover.
• Insert two AA batteries matching the -/+ polarities of the battery to
the battery compartment.
• Put on the battery cap and rotate it tightly according to the following
fi gures.
POWER ON AND RESETTING THE WRENCH
• Press to power on the digital torque wrench.
• Usually press to reset the digital torque wrench before using it.
ATTENTION:
If an external force is applied to the torque wrench during power-on/reset
or wake up period, an initial torque offset will exist in the memory.
ACTIVATION DURING SLEEP MODE
• The wrench will auto sleep after about 2 minutes idle for power
saving. Press
to wake up the wrench during the sleep mode.
CAUTIONS:
During communication period (Send appears), the sleep function is disabled.
RESETTING THE WRENCH
• To reset the wrench, loosen the battery cap then tighten it to re-start.
• After reset, remember to press
.
LOW BATTERY VOLTAGE PROTECTION
• If the battery serial voltage is under 2.3 volts, the wrench will display
a battery symbol and then turn off after a while.
SET UP
1 . Power On/Clear
2 . Unit Selection/Setting
3 . Up/Down Button
4 . Pre-Setting No.
STEP 1: PRE-SETTING NO.
Note:
1.If is appeared, that
means this wrench has ever been
applied more than 110% of maximum
torque.
2.The maximum capacity for
“Pre-setting No.” is 9 sets.
3.
The “Pre-Setting No.” is in sequential.
STEP 2: UNIT SELECTION
N.m
M
T
N.m
M
T
1
2
3
4
N.m
M
T
Pre-setting: M1
N.m
M
T
Press
M
Press
Pre-setting: M2
Pre-setting: M9
M
N.m
M
T
N.m
M
T
Pre-setting: Unit: N.m
in.lb
M
T
Press
Press
ft.lb
M
T
Pre-setting: Unit: in.lb
Pre-setting: Unit: ft.lb
Press
kg.cm
M
T
Pre-setting: Unit: kg.cm
STEP 3: SET TORQUE VALUE
N.m
M
T
Pre-setting Torque Value
N.m
M
T
Press
Press
N.m
M
T
Increase Max. Torque Value
Decrease Max. Torque Value
Note:
1.The “Unit Selection” is in sequential.
STEP 4: PEAK HOLD /TRACK
MODE SELECTION
N.m
M
T
Track Mode
T
Long Press
P
Set Peak/Track mode
Press
Record No.
Press
for selection
Set Peak/Track mode
Press
Clear Record
Press
N.m
M
P
Peak Hold Mode
Note:
1.Please skip this procedure and
continue to the next spet.
*Note 1
*Note 1
TRACK MODE OPERATION
N.m
M
T
Max. Target Value
N.m
M
T
((...((... ...))...))
N.m
M
T
START
(system initial)
*Note 1
Apply torque over 5 N.m
*Note 2
Current Torque Value
Over 80% of Max.
Target Value
N.m
M
PT
Current Torque Value
((...((... ...))...))
Buzzer
Green LED
Over 80% of Set Torque
Approach
Max.
Target Value
(((((((( ))))))))
((((((((  )))))))
Buzzer
Red LED
Approach Max. Set Torque
Note:
1. If
is appeared, that means this wrench has ever been
applied over than 110% of maximum torque.
2. When using track mode, if you apply torque over 5 N.m, the LCD
dispay will start to display the torque value. If the applied is less than
5 N.m, the LCD display does not have any value changes.
The smallest torque for E.316-30D series is 0.5 N.m.
3. The green LED will be on for 80%, 85%, 90%, 95% and 97.5% of
maximum setting torque.
4. The red LED will be on 99,5% of maximum setting torque.
PEAK HOLD MODE OPERATION
N.m
M
P
Max. Target Value
N.m
P
((...((... ...))...))
START
(system initial)
*Note 1
Apply torque
Current Max. Value
(Peak Hold)
N.m
M
P
((...((... ...))...))
Buzzer
Green LED
Over 80% of Set Torque
Released
Apply torque
N.m
P
M
Recording
Flashing
*Note 2
Approach Max. Target Value
N.m
M
P
*Note 3
(((((((  )))))))
((((((( ))))))))
Buzzer
Red LED
Approach Max. Set Torque
Note:
1. If
is appeared, that means this wrench has ever been
applied over than 110% of maximum torque.
2. If
is appeared, that means the wrench’s memory is full and
the next value record can not be written in. Please refer the “Peak Hold
Mode Recorded Value Review” section to clear the momory data.
3. The green LED will be on for 80%, 85%, 90%, 95% and 97.5% of
maximum setting torque.
4. The red LED will be on for 99,5% of maximum setting torque.
PEAK HOLD MODE RECORDED VALUE REVIEW
N.m
M
P
Peak Hold/Track Mode
*Note 1
Long Press
(Clear)
Record Value
Set Peak/Track Mode
Auto Change
Record No.
*Note 2
Press
*Note 3
N.m
Press
Clear Record
Press
No
Yes
Deleted
(give up)
Communication
*Note 4, 5, 6
Communication
Press
N.m
M
P
Peak Hold/Track Mode
(Exit)
Note:
1. The “Peak Hold” mode recorded value review also can be operated in
“Track” mode operation.
2. If you operate in the “Peak Hold” mode, the display will show
P
and please go to next step.
3. If the record is empty, it will show
.
4. This function is not supported on all type of models.
5. Communication mode is for uploading record data to PC.
6. Communication mode is also for calibration of torque wrench. Please
contact your local dealer for more information.
ANGLE MODE OPERATION
((...((... ...))...))
Flashing
M
Angle Mode
*Note 1
M
Auto Change
Apply force and turn
*Note 2
*Note 3
Loose
*Note 5
Note 2:
1. When entering angle mode, the unit will be Degree.
2. When angle is in auto initial mode, please keep the wrench steady
without any disturbance.
3. After a while, the angle function will be in initiative mode with the
fl ashing
.
4. When loosing the wrench with angle mode, the display will show the
corresponding torque value with fl ashing state.
5. The Green LED will be on with 80%, 85%, 90%, 95% and 97.5% of
target degree.
6.
When reaching the target degree, the green and red LED will be on at the
same time.
Apply force and turn
Approach 80% of target degree
Current Angle
Press
Current Torque
N.m
*Note 4
Reach 80% of target degree
Apply force and turn
Approach target degree
Loose
Current Torque
N.m
*Note 6
((...((... ...))...))
Auto Change
Pre-setting Unit: N-m
Unit Selection: in-lb
Pre-seting Unit: ft-lb
Pre-setting Unit: kg-cm
Press
TORQUE UNIT SELECTION UNDER ANGLE MODE
M
Angle Mode
*Note 1
*Note 2
*Note 3
ft.lb
N.m
Long Press
Set Peak/Track Mode
in.lb
kg.cm
Press
Press
Press
Press
Note:
1. The unit setting could be also entered from the torque mode.
2. Please skip the procedure and go to next step.
3. The unit selection is cyclic
*Note 4
*Note 3
*Note 4
N.m
M
P
Long Press
KEY LOCK
Lock on/off selection
Press
N.m
M
P
Auto Change
*Note
Note:
If ‘‘LoC on’’ is set, the display will show
while pressing
, ,
Current Degree