Installation Instructions / Warranty 90573801-00 07/2005 Starck X 10406001
Starck X Free-Standing Tub Filler 10406001 Technical Specification Maximum incoming water pressure Recommended water pressure Recommended incoming hot water temp Spout flow rate @ 45 psi Handshower flow rate 145 psi 14.5 - 72 psi 120oF - 140oF* 5.75 gpm 2.5 gpm This unit is not anti-scald. If anti-scald capability is desired, or is required by local plumbing codes, install this unit in combination with Hansgrohe remote pressure balance valve 13418181 or similar unit.
Installation If installing with Duravit Starck X tub, please see the instructions st arting on page 5. • Cut the plaster shield on the rough-in 3/8" above the finished floor. • Remove the flush block using an 8 mm allen wrench (not included) to remove the 4 bolts. Do not discard the bolts! • Install the tub filler to the rough. Slide the escutcheon up and out of the way. Make sure that the unit is level in all planes. Use the 8mm allen wrench to tighten the bolts evenly.
• Seal the floor around the plaster shield with a waterproof sealant compatible with the floor surface. Lower the escutcheon to the floor • Push the housing over the top of the tub filler. Tighten the nuts. • Install a black rubber hose washer in the short hose end connection. Connect this end to the handshower port on the bottom of the housing. Install the screen washer in the long hose end connection. Screw this end to the handshower.
Installation with Duravit Starck X Tub There must be a minimum 1 1/8” air gap between the tub filler and the top of the tub. If the air gap is not at least 1 1/8”, order extension 97686000 separately. • Cut the plaster shield on the rough-in 3/8" above the finished floor. • Remove the flush block using an 8 mm allen wrench (not included) to remove the 4 bolts. Do not discard the bolts! • Seal the floor around the plaster shield with a waterproof bathroom sealant compatible with the floor surface.
• Install the tub. • Place the tub escutcheon over the end of the tub filler. • Install the tub filler to the rough. Slide the escutcheon and the tub escutcheon up and out of the way. Make sure that the unit is level in all planes. Use the 8mm allen wrench to tighten the bolts evenly.
• Lower the tub escutcheon and escutcheon to the floor • Push the housing over the top of the tub filler. Tighten the nuts. • Install a black rubber hose washer in the short hose end connection. Connect this end to the handshower port on the bottom of the housing. Install the screen washer in the long hose end connection. Screw this end to the handshower. Lower the handshower into the handshower holder on the side of the tub filler. • Seal the floor around the tub.
Reset the High Temperature Limit Stop (Optional) • Use a 4 mm allen wrench to push the gray rubber screw cover through the hole in the handle. Loosen the handle screw 4 complete turns. Pull the handle off. Retrieve the screw cover. • Remove the nut cover and the handle screw. • Center the cartridge stem. • Remove the handle screw. Pull the green high temperature limit stop straight off the cartridge.
User Instructions • Pivot the lever upward to turn the water on, down to turn it off. Pivot the handle left to obtain warmer water, to the right to obtain cooler water. • When the unit is turned on, the water will come from the tub filler. Pull the diverter knob to obtain water from the handshower When the water is turned off, the diverter will automatically reset to the tub filler position. • The handshower uses the Rubit!™ self-cleaning system.
Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty. Cleaning Materials for Faucets and Showers • • • • To remove lime scale, use only products made specifically for that purpose.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no rinse” cleaning products, or the use of the product in any manner contrary to the product instructions. C.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel. 770 360-9880 • Fax 770 360 9887 www.hansgrohe-USA.
