Operation Manual

english
13
1
Instruction manual
Important! Read the entire manual before using the oven. The documentation and accessories are
inside the oven.
The texts in the manual correspond to the numbered diagrams.
2
Installation
Using the oven
To fi nd out which model your oven is (“a”, “b”,
“c”, “d”, “e”, “f”) compare its control panel with
the control panels shown in the illustrations.
1.1 Unpacking. Remove all the protective
packaging elements.
1.2 Mains connection. Always take into account
the data on the reference plate (1.2.1) and
the measurements of the cabinet the oven
will be housed in (1.2.2, 1.2.3).
Freestanding ovens: the appliance must be
connected to the mains with a fi xed single-
phase connection with the neutral (blue)
connection guaranteed (1.2.4). Fit the oven
into the space, ensuring there is no excess
cable in the upper part (1.2.5, 1.2.6). Screw
it to the fi tting using the two screws supplied
(1.2.7).
Multi-purpose ovens for vitro-ceramic
hobs: to avoid hazard, the oven may only
be installed with the vitro-ceramic hobs
recommended by the manufacturer. Fit the
cooking hob into the worktop and remove
the switch box (1.2.8). Insert the hob in the
worktop space according to the installation
requirements (see the hob manual) (1.2.9).
Insert the oven into the cabinet space,
leaving enough room for handling (1.2.10).
Screw the switch box onto the oven
(1.2.11, 1.2.12). Connect the hob to the
oven (1.2.13). Fully insert the oven and fi x
it in place with the two screws supplied
(1.2.14, 1.2.15). Firmly push in the control
accessories, according to the cooking ring
type (1.2.16), and the controls (1.2.17).
Oven + hob unit: connect the oven to
the mains (1.2.4). Insert the hob in the
worktop space according to the installation
requirements (see the hob manual) (1.2.18).
0
Identifi cation
Insert the oven into the cabinet space,
leaving enough room for handling (1.2.10).
Connect the hob to the oven (1.2.19). Fully
insert the oven and fi x it in place with the two
screws supplied (1.2.14, 1.2.15).
Before using your new oven for the fi rst time,
heat it up while empty (with no food in it and
with the control turned to
, at for 30 minutes
at 250ºC). It may produce some smoke or a bad
smell (this is normal and is caused by the oven
heating up grease residue etc.). When it has
cooled down, pre-clean it by wiping the inside
with a damp cloth.
2.1 Accessories. Depending on the model,
the oven is equipped with a Standard Tray
(2.1.1), a Deep Tray (2.1.2) and a
Standard Rack (2.1.3), which function
separately. You may also combine any tray
with the standard rack (2.1.4) to
form a unit. The half-removable rack (2.1.5)
and the fully-removable rack (2.1.6, 2.1.7)
support the trays or the unit (2.1.8). Take
into account the position of the racks when
placing them inside the oven. They have anti-
overturn side stops (2.1.9).
2.2 Accessory positions. The accessories
can be fi tted in 5 different positions,
.
2.3 Setting the time. Ordinary clock: Pull on
the lower dial and turn it to the right (2.3.1).
Set the time (2.3.2). Digital clock: press the
button. (2.3.3). Set the time using
the
and buttons (2.3.4). After a few
seconds
will stop fl ashing (2.3.5).
Note: the time will need to be set again after an
electricity cut or when the hour changes.
2.4 Cooking the food. Place the food in the
oven. Consult the cooking table to choose
the accessory or accessories to be used and
their position. Close the oven door.