Instructions / Assembly

ManualsBrandsFahrenheat ManualsElectric Wall Heaters2,000-Watt Small Room Wall Heater

WHEN USING ELECTRIC APPLIANCES, BASIC PRECAU-

TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE

RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PER-

SONS, INCLUDING THE FOLLOWING:

1. Read all instructions before installing or using this heater.

2. This heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes, etc. and

curtains at least 3 feet (0.9 m) from the front of the heater.

3. Extreme caution is necessary when any heater is used by or

near children or invalids and whenever the heater is left

operating and unattended.

4. Do not operate any heater after it malfunctions. Disconnect

power at service panel and have heater inspected by a rep-

utable electrician before using.

5. Do not use outdoors.

6. To disconnect heater, turn controls to off, and turn off power

to heater circuit at main disconnect panel.

7. Do not insert or allow foreign objects to enter any ventilation

or exhaust opening as this may cause an electric shock, fire,

or damage to the heater.

8. To prevent a possible fire, do not block air intake or exhaust

in any manner.

9. A heater has hot and arcing or sparking parts inside. Do not

use it in areas where gasoline, paint, or flammable liquids

are used or stored.

10. Use this heater only as described in this manual. Any other

use not recommended by the manufacturer may cause fire,

electric shock, or injury to persons.

11. This heater is provided with a an automatic safety limit con-

trol that shuts the heater off should it overheat. If you find

the heater off, inspect for any objects on or adjacent to the

heater that may have blocked the airflow or otherwise

caused high temperatures to have occurred and remove any

objects that may have caused the overheating. Refer to the

Maintenance Instructions section of this manual for how to

reset this safety control.

12. This heater is intended for comfort heating applications and

not intended for use in special environments. Do not use in

damp or wet locations such as marine or greenhouse or in

areas where corrosive or chemical agents are present.

13. When installing, see INSTALLATION INSTRUCTIONS for

additional warnings and precautions.

14. For safe and efficient operation, and to extend the life of your

heater, keep your heater clean - See MAINTENANCE

INSTRUCTIONS.

SAVE THESE INSTRUCTIONS

Installation, Operation & Maintenance Instructions

WARNING

ECR 40339 02/15 5200-11202-003

IMPORTANT INSTRUCTIONS

FFC Series

Fan-Forced Wall Heaters

MODEL VOLTS WATTS/AMPS WATTS/AMPS*

FFC1512 120 1500W/12.5A 750W/6.3A

FFC1012 120 1000W/8.3A 500W/4.2A

FFC1548

240 1500W/6.3A 750W/3.1A

208 1125W/5.4A 563W/2.7A

FFC1048

240 1000W/4.2A 500W/2.1A

208 750W/3.6A 375W/1.8A

FFC2048

240 2000W/8.3A 1000W/4.2A

208 1500W/7.2A 750W/3.6A

Table 1. Specifications

* Factory wired for full wattage, field convertible to half wattage.

CLIP-N-FIT

FEATURE

Patented CLIP-N-FIT

feature (US Patented #6,172,343)

allows installer to pick a wattage onsite. Factory wired for

full wattage, easily field adjustable for half wattage. Half

wattage option is permanent change complying with

many local electrical code requirements.

Conforms to ANSI/UL2021 and

CSA C22.2, No. 46

Summary of content (12 pages)

PAGE 1
FFC Series Fan-Forced Wall Heaters Conforms to ANSI/UL2021 and CSA C22.2, No. 46 Installation, Operation & Maintenance Instructions Table 1. Specifications MODEL FFC1512 FFC1012 FFC1548 FFC1048 FFC2048 VOLTS 120 120 240 208 240 208 240 208 WATTS/AMPS 1500W/12.5A 1000W/8.3A 1500W/6.3A 1125W/5.4A 1000W/4.2A 750W/3.6A 2000W/8.3A 1500W/7.2A WATTS/AMPS* 750W/6.3A 500W/4.2A 750W/3.1A 563W/2.7A 500W/2.1A 375W/1.8A 1000W/4.2A 750W/3.
PAGE 2
INSTALLATION INSTRUCTIONS cable clamp Supply wiring cable To prevent a possible fire, injury to persons or damage to the heater, adhere to the following: lead holeS nailS or ScrewS TOP VIEW 2. All wiring procedures and connections must be in accordance with the National Electrical Code (NEC) and Local Codes having jurisdiction and the heater must be grounded. 3. Power supply may enter back-box through any knockout provided (see Figure 1). RUBBER SHIM TOP OF BACK BOX 4.
PAGE 3
CLIP WIRE (FOR 1/2 WATT) THERMOSTAT L1/N L1 OFF YEL-120V RED-208V/240V POWER L2 L2 ELEMENT CYC SELF-HOLD LIMIT BLU - 240V/208V BLK - Others MOTOR THERMAL FUSE YEL-120V RED-208V/240V G Figure 2 - Wiring Diagram GND NOTE: Heaters are factory wired per nameplate voltage and wattage. Refer to How to Reduce wattage for instructions on reducing to half wattage if lower wattage is desired and make change before installing heat deck.
PAGE 4
CAUTION - DO NOT CONTINUE TO ATTEMPT TO USE THE HEATER IF THE SAFETY CONTROL REPEATEDLY OPERATES AFTER BEING RESET. TO DO SO COULD PERMANENTLY DAMAGE THE HEATER OR CREATE A FIRE OR SAFETY HAZARD. TO REDUCE RISK OF FIRE AND ELECTRIC SHOCK OR INJURY, DISCONNECT ALL POWER COMING TO HEATER AT MAIN SERVICE PANEL AND CHECK THAT THE ELEMENT IS COOL BEFORE SERVICING OR PERFORMING MAINTENANCE.
PAGE 5
Serie FFC Calefactores de pared con ventilador Instrucciones de instalación, utilización y mantenimiento Table 1. Specifications MODELO VOLTAJE FFC1512 FFC1012 120 120 240 208 240 208 240 208 FFC1548 FFC1048 FFC2048 WATTS/AMPS 1500W/12.5A 1000W/8.3A 1500W/6.3A 1125W/5.4A 1000W/4.2A 750W/3.6A 2000W/8.3A 1500W/7.2A WATTS/AMPS* 750W/6.3A 500W/4.2A 750W/3.1A 563W/2.7A 500W/2.1A 375W/1.8A 1000W/4.2A 750W/3.6A CARACTERÍSTICA CLIP-N-FIT® La característica patentada CLIP-N-FIT® (Patente de los EE. UU. N.
PAGE 6
INSTRUCCIONES DE INSTALACIÓN Abrazadera para cable Cable de alimentación Para evitar la posibilidad de incendios, lesiones personales o averías en el calefactor, cumpla las siguientes indicaciones: Agujeros de fijación Desconecte la alimentación del calefactor en el panel de suministro eléctrico antes de instalarlo o repararlo. Clavos o tornillos 2.
PAGE 7
cortar alambre CLIP WIRE (FOR 1/2 WATT) Thermostato THERMOSTAT L1/N L1 OFF Amarillo - 120V YEL-120V Rojo - 208V/240V RED-208V/240V Potencia POWER L2 L2 Elemento ELEMENT CYC Fusible SELF-HOLD LIMIT térmic BLU - 240V/208V MOTOR THERMAL Límite autorretenido FUSE Amarillo YEL-120V - 120V RED-208V/240V Rojo - 208V/240V Negro-120V/208V/240V BLK - Others G Figura 2 - Diagrama de conexión GND NOTA: los calefactores vienen cableados de fábrica de acuerdo a la potencia y el voltaje indicados en su p
PAGE 8
4. Si el calefactor vuelve a funcionar mal y se enciende la luz roja, desconecte la alimentación eléctrica del circuito y haga revisar el calefactor por un electricista matriculado. DESCARGAS ELÉCTRICAS O LESIONES, DESCONECTE LA ALIMENTACIÓN DEL CALEFACTOR DESDE EL TABLERO DE DISTRIBUCIÓN PRINCIPAL Y VERIFIQUE QUE EL ELEMENTO ESTÉ FRÍO ANTES DE REPARARLO O REALIZAR TAREAS DE MANTENIMIENTO.
PAGE 9
Série FFC Radiateurs muraux à air pulsé Instructions d’installation, d’utilisation et d’entretien Tableau 1 - Spécifications MODÈLE FFC1512 FFC1012 FFC1548 FFC1048 FFC2048 WATTS/AMPS 1500W/12.5A 1000W/8.3A 1500W/6.3A 1125W/5.4A 1000W/4.2A 750W/3.6A 2000W/8.3A 1500W/7.2A VOLTAJE 120 120 240 208 240 208 240 208 WATTS/AMPS* 750W/6.3A 500W/4.2A 750W/3.1A 563W/2.7A 500W/2.1A 375W/1.8A 1000W/4.2A 750W/3.
PAGE 10
INSTRUCTIONS D'INSTALLATION Serre-câble Câble d’alimentation Pour éviter un possible départ d’incendie, des blessures corporelles ou des dommages au radiateur, respectez ces consignes : Débranchez toute alimentation secteur arrivant au panneau de service principal avant de câbler ou d’intervenir pour du service. 2.
PAGE 11
fil découpez CLIP WIRE Thermostat THERMOSTAT L1/N L1 OFF Energie POWER L2 L2 CYC (FOR 1/2 WATT) Element ELEMENT jaune - 120V YEL-120V Rouge - 208V/240V RED-208V/240V Fusible SELF-HOLD LIMIT thermique BLU - 240V/208V Motuer MOTOR THERMAL Limite auto-maintenue FUSE jaune - 120V YEL-120V Rouge - 208V/240V RED-208V/240V Noir-120V/208V/240V BLK - Others G Figure 2 Schéma de câblage GND REMARQUE: Les radiateurs sont câblés en usine selon les indications de tension et puissance de la plaque sign
PAGE 12
4. Si le radiateur est de nouveau défaillant, et que son voyant rouge s’allume, coupez l’alimentation électrique en amont et faites inspecter le radiateur par un électricien qualifié. NE CONTINUEZ PAS D’ESSAYER D’UTILISER LE RADIATEUR SI SON CONTRÔLE THERMIQUE SE DÉCLENCHE À RÉPÉTITION APRÈS SA RESTAURATION. EN LE FAISANT VOUS POURRIEZ L’ENDOMMAGER DE FAÇON IRRÉMÉDIABLE OU CAUSER UN DÉPART D’INCENDIE OU DES RISQUES POUR LA SÉCURITÉ.