Instructions / Assembly

ManualsBrandsFahrenheat ManualsHeating, Ventilation, and Air Conditioning10-1/2 in. x 12-1/2 in. 2,000-Watt Wall Heater

C Series

B Model

Fan-Forced Wall Heaters

with

Clip’n’Fit

Board

File #E21609

FRONT COVER

BACK BOX

HEATER

ASSEMBLY

Dear Owner,

Congratulations! Thank you for purchasing this new heater manufactured by Marley Engineered Products. You have made

a wise investment selecting the highest quality product in the heating industry. Please carefully read the installation and

maintenance instructions shown in this manual. You should enjoy years of efficient heating comfort with this product from

Marley Engineered Products... the industry’s leader in design, manufacturing, quality and service.

... The Employees of Marley Engineered Products

Read Carefully - These instructions are written to help you prevent

difficulties that might arise during installation of heaters. Studying

the instructions first may save you considerable time and money

later. Observe the following procedures, and cut your installation

time to a minimum. CAUTION - TO REDUCE RISK OF FIRE AND

ELECTRIC SHOCK:

1. Disconnect all power coming to heater at main service panel

before wiring or servicing.

2. All wiring must be in accordance with the National and Local

Electrical Codes and the heater must be grounded.

3. Verify the power supply voltage coming to heater matches the

ratings printed on the heater nameplate before energizing.

4. This heater is hot when in use. To avoid burns, do not let bare

skin touch hot surfaces.

5. Do not insert or allow foreign objects to enter any ventilation or

exhaust opening as this may cause an electric shock, fire, or

damage to the heater.

6. Grille and discharge air are hot when in use. Do not install or use

heater in any area where airflow from heater may be blocked or

obstructed. Do not install behind doors, furniture, towel racks,

curtains, or boxes. Hot air may damage certain fabrics and plas-

tics. Always keep electrical cords, beddings, crates, drapes, and

other combustibles away from heater. Do not install heater in

ceiling.

7. A heater has hot and arcing or sparking parts inside. Do not use

it in areas where gasoline, paint, or flammable liquids are used

or stored.

8. Use this heater only as described in this manual. Any other use

not recommended by the manufacturer may cause fire, electric

shock, or injury to persons.

9. This heater is not approved for use in corrosive atmospheres

such as marine, green house, or chemical storage areas.

10. When wall mounted, heater must only be installed in a vertical

direction (motor below element) as shown in this manual. Do not

install sideways, upside down.

11. Heater must be installed with CBB (Type CO2-BB) Back Box.

12. The following minimum clearances must be maintained:

• Wall Mounting:

Heater to floor - 4.5 in. (114 mm)

Heater to adjacent wall - 4.5 in. (114 mm)

Heater to ceiling - 12 in. (305 mm).

• Ceiling Mounting (Max 1000 Watts)

Heater to any wall - 12” (305mm)

13. When wiring, power supply must enter through knockouts in left

side of back box. Do not use the knockouts in right side back

box. Refer to Fig. 1.

To determine which side is left or right:

1.) Orient the back box so the “TOP” marking and arrows are

visible and upright; and 2.) Ensure that the fan deck is oriented

with the element side on the “TOP” side of the back box.

14. Do not operate heater without grille installed.

15. Do not use heater for dry out. Paint, plaster, sawdust, and dry-

wall sanding dust will damage heater and must be kept out of

heater.

16. Keep heater clean. See maintenance and cleaning instructions

on page 3.

Installation & Maintenance Instructions

SAVE THESE INSTRUCTIONS

WARNING

US Patent No. 6,172,343

Summary of content (4 pages)

PAGE 1
BACK BOX HEATER ASSEMBLY File #E21609 C Series B Model Fan-Forced Wall Heaters with Clip’n’Fit® Board FRONT COVER US Patent No. 6,172,343 Installation & Maintenance Instructions Dear Owner, Congratulations! Thank you for purchasing this new heater manufactured by Marley Engineered Products. You have made a wise investment selecting the highest quality product in the heating industry. Please carefully read the installation and maintenance instructions shown in this manual.
PAGE 2
GENERAL Wall Mounted •The C series heaters are designed for recessed installation in 2 X 4 stud or larger wall using the model CBB (Type CO2-BB) back box. The heater may be wired using standard building (60 degrees C minimum) wire. ! CAUTION TO PREVENT POSSIBLE WIRING DAMAGE CUT EXCESS SUPPLY WIRE INSIDE BACKBOX TO PROVIDE APPROXIMATELY 6 INCHES FOR CONNECTION TO HEATER LEADS. AFTER CONNECTIONS ARE MADE, MAKE SURE CONNECTIONS ARE TIGHT AND ALL WIRING IS POSITIONED AWAY FROM FAN BLADE AND HEATING ELEMENT.
PAGE 3
INSTALLATION OF FRONT COVER (GRILLE) AND THERMOSTAT KNOB 1. Fasten front cover to heater assembly using the (2) long screws supplied. 2. Fit the thermostat knob onto the thermostat shaft (if provided) and push into place. a CAUTION THE ILLUMINATED INDICATOR LIGHT SIGNIFIES THE HEATER HAS BEEN SUBJECTED TO SOME ABNORMAL CONDITION CAUSING IT TO OVERHEAT. CHECK HEATER TO INSURE THAT IT HAS NOT BEEN BLOCKED IN ANY MANNER (IF SO, REMOVE BLOCKAGE).
PAGE 4
LIMITED WARRANTY All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation, except heating elements which are warranted against defects in workmanship and materials for five years from date of installation.