Owner manual

ManualsBrandsFairbanks ManualsHardware9109 Series Omnicell

A. Introduction

The 9109 family of OMCs are constructed of stainless steel load cells,

have 4 hole mounting pattern for securing, and built in checking. All cells used

are true hermetically sealed units. The OMC assemblies are compact,

resistant to oxidation, and have replaceable 'suspension' parts for super long life

and excellent resolution. See the following chart for either stainless steel or

galvanized mounting assemblies.

B. Specifications

Resistance: 500 Ohms

Output: 2 mV/v (see certificate for exact output spec)

Type: Double-Ended Shearbeam

Wiring: (Color code on the load cell cable)

Black - Excitation

Green + Excitation

White + Signal

Red - Signal

Yellow Shield

C. Capacities:

Product

No.

Capacity Description

98463 1 K 9109-1, SS, NTEP, FM, Hermetically Sealed, DESB, SS Mount

98464 2.5K 9109-2, SS, NTEP, FM, Hermetically Sealed, DESB, SS Mount

98465 5K 9109-3, SS, NTEP, FM, Hermetically Sealed, DESS, SS Mount

98466 10K 9109-4, SS, NTEP, FM, Hermetically Sealed, DESB, SS Mount

98467 25K 9109-5, SS, NTEP, FM, Hermetically Sealed, DESB, SS Mount

98468 50K 9109-6, SS, NTEP, FM, Hermetically Sealed, DESB, SS Mount

98469 1K 9109-7, SS, NTEP, FM, Hermetically Sealed, DESB, GALV Mount

98470 2.5K 9109-8, SS, NTEP, FM, Hermetically Sealed, DESB, GALV Mount

98471 5K 9109-9, SS, NTEP, FM, Hermetically Sealed, DESB, GALV Mount

98472 10K 9109-10,SS, NTEP, FM, Hermetically Sealed, DESB, GALV Mount

98473 25K 9109-11,SS, NTEP, FM, Hermetically Sealed, DESB, GALV Mount

98474 50K 9109-12,SS, NTEP, FM, Hermetically Sealed, DESB, GALV Mount

(DESB = Double Ended Shearbeam GALV = Galvanized)

50629 1 3/04 Issue #2

Bulletin 50629 Issue #2

Omnicell 9109 Series:

Instructional Bulletin 3/04

Summary of content (6 pages)

PAGE 1
Bulletin 50629 Issue #2 Omnicell 9109 Series: Instructional Bulletin 3/04 A. Introduction The 9109 family of OMCs are constructed of stainless steel load cells, have 4 hole mounting pattern for securing, and built in checking. All cells used are true hermetically sealed units. The OMC assemblies are compact, resistant to oxidation, and have replaceable 'suspension' parts for super long life and excellent resolution. See the following chart for either stainless steel or galvanized mounting assemblies. B.
PAGE 2
D. Installation: 10 1 The Omnicell is fully assembled when shipped and ready for installation.
PAGE 3
E. Parts List: Part # 98573 98574 98575 98576 98577 98578 98579 98580 98581 98582 98583 98584 50629 Description Mild Steel Omni Mounts, includes suspension 1-10K Mild Steel Omni Mounts, includes suspension 25K Mild Steel Omni Mounts, includes suspension 50K Stainless Steel Omni Mounts, includes suspension 1-10K Stainless Steel Omni Mounts, includes suspension 25K Stainless Steel Omni Mounts, includes suspension 50K Load Cell SS DESB 1K Load Cell SS DESB 2.
PAGE 4
Typical Load Cell Mounting Orientation OP TIG OP TIG OP TIG OP TIGHT FREE FLOATING LOCKED OP OP OP OPE TIGHT OPE GUIDED FREE FLOATING TIG 50629 OP 4 3/04 Issue #2
PAGE 5
See Detail A,B,C for Optional Mounting Options Note: It is important to set the checking clearances so that expansion and contraction of the supported vessel will be taken into account. On a four (4) load cell tank, hopper, vessel; keep the clearance on I cell assembly (#I) as an 'anchor' with tight, minimal clearances. On the other three (3), set with the looser, more open clearances to allow for expansion and / or contraction.
PAGE 6
individual parts are NOT available. A. Mild Steel Kits, by Capacity: 1 thru 10K Kit # 98573 25K Kit # 98574 50K Kit # 98575 Includes: 1 Top Rocker 1 Top Plate 1 Spring Pin 4 Socket Cap Screws 5/8-11 x 1 ¼" 2 Cross Beams 4 Legs 2 Stainless Sheet 2 Sliding Load Pin w/ "O" Ring and Slide Plate 2 V-Ring 1 Base Plate 4 Hex Head Screws ¼" -20 x ½" 2 Uplift Hook B.