Zebra® GC420d™ Desktop Thermal Printer User Guide 51319 05/13
ii P1052685-001 GC420d™ User Guide 5/23/2012
iii ©2012 ZIH Corp. GC420,GC420d, ZBI, ZBI 2.0, ZBI-Developer, Uni-Ribbon, ZebraDesigner, ZebraNet, EPL, EPL2, ZPL, ZPL II, OpenACCESS and all product names and numbers are Zebra trademarks, and Zebra, the Zebra head graphic, ZPL, ZPL II, Element Energy Equalizer circuit, E3 Circuitand, and ZebraNet are registered trademarks of ZIH Corp. All rights reserved. All other trademarks are the property of their respective owners.
iv FCC Compliance Statement This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Devices, pursuant to Part 15 of the FCC Rules.
About This Document This section provides you with contact information, document structure and organization, and additional reference documents. Contents Who Should Use This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi How This Document Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi Who Should Use This Document Who Should Use This Document This User Guide is intended for use by any person who needs to operate or to troubleshoot problems with the printer. How This Document Is Organized The User Guide is set up as follows: P1052685-001 Section Description Introduction on page 1 This section describes what you get in your shipping box and provides an overview of printer features.
Contacts Contacts Technical Support via the Internet is available 24 hours per day, 365 days per year. Web Site: www.zebra.com E-mail Back Technical Library: E-mail address: emb@zebra.com Subject line: Emaillist Self Service Knowledge Base: www.zebra.com/knowledgebase Online Case Registration: www.zebra.
viii Document Conventions Document Conventions The following conventions are used throughout this document to convey certain information. Alternate Color (online only) Cross-references contain hot links to other sections in this guide. If you are viewing this guide online in .pdf format, you can click the cross-reference (blue text) to jump directly to its location. Command Line Examples Command line examples appear in Courier New font.
Contents • About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Who Should Use This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi How This Document Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
x Long Term Printer In-activity or Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modes of Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Print Media Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xi Troubleshooting Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing a Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recalibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resetting the Factory Default Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xii Notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ _______________________________________________________
1 Introduction This section describes what you get in your shipping box and provides an overview of printer features. This includes procedures that describe how to open and close the printer and report any problems. Contents GC420d™ Thermal Printers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What’s in the Box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpack and Inspect the Printer . . .
2 GC420d™ Thermal Printers GC420d™ Thermal Printers The Zebra® GC420d™ model is the best value in a desktop thermal printer. The GC420d™ printer provides direct thermal printing at speeds up to 4 ips (inches per second) at a 203 dpi (dots per inch) print density. The GC420d™ supports both ZPL™ and EPL™ Zebra printer programming languages and a wide variety of interface and feature options.
What’s in the Box? What’s in the Box? Save the carton and all packing materials in case you need to ship or store the printer later. After unpacking, make sure you have all parts. Follow the procedures for inspecting the printer to familiarize yourself with printer parts so you can follow the instructions in this book.
4 What’s in the Box? Your Printer Status Light Fan-Fold Media Entry Slot Feed Button Release Latches Power Switch Release DC Power Receptacle Latches Interface Connectors Opening the printer To access the media compartment, you must open the printer. Pull the release latches towards you and lift the cover. Check the media compartment for loose or damaged components.
What’s in the Box? Printer Features Printhead Gap Sensor Roll Holder and Media Guides BlackLine Sensor Head-Up Sensor (inside) Dispenser Option Media Guides Platen Roller Media Guide Adjustment Dispenser Door (open) Label-Taken Sensor 5/23/2012 GC420d™ User Guide Pinch Roller Peel Bar P1052685-001 5
6 What’s in the Box? Operator Controls Power Switch Press up to turn ON or down to turn OFF the printer. Caution • The printer power should be turned off before connecting or disconnecting the communications and power cables. Power Switch Power OFF Power ON Power Switch Feed Button • Tap the Feed button once to force the printer to feed one blank label. • Press the Feed button to take the printer out of a “pause” condition.
What’s in the Box? Status Light Located on the top case next to the feed button, the status light functions as a printer operational indicator (see Status Light Descriptions on page 60).
8 What’s in the Box? Closing the printer 1. Lower the top cover. 2. Press down until the cover snaps closed.
2 Getting Started This section describes how to set up your printer for the first time and use the most common operating procedures for loading media. Contents Attaching Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading Roll Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing a Test (Printer Configuration) Label . . . . . . . . . . . . . . . . . . . . . . . . . .
10 Attaching Power Attaching Power Important • Set up your printer so that you can handle the power cord easily if needed. To make certain the printer cannot carry electrical current, you must separate the power cord from the power supply receptacle or AC electrical outlet. Caution • Never operate the printer and power supply in an area where they can get wet. Serious personal injury could result! 1. Make sure the printer’s power switch is in the off position (down). 2.
Loading Roll Media Loading Roll Media When you load media, you must place the roll onto the media hangers. You must use the correct media for the type of printing you require. Preparing Media Whether your roll media is inside or outside wound, you load it into the printer the same way. • Remove the outside length of media. During shipment, handling, or storage, the roll may become dirty or dusty. Removing the outside length of media avoids dragging adhesive or dirty media between the printhead and platen.
12 Loading Roll Media Placing the Roll in the Media Compartment 1. Open the printer. Remember that you need to pull the release latch levers toward the front of the printer. 2. Open the media guides by turning the media guide adjustment knob toward the rear of the printer.
Loading Roll Media 3. Pull the media roll holders open with your free hand and place the media roll on the roll holders and release. Orient the media roll so that its printing surface will face up as it passes over the platen (drive) roller.
14 Loading Roll Media 4. Pull the media so that it extends out of the front of the printer. Thread the media under the media guides.Verify the roll turns freely. The roll must not sit in the bottom of the media compartment. Verify that the media’s printing surface is facing up. 5. Close the media guides by turning the guide adjuster knob to the front. They should just touch, but not restrict. the edges of the media. 6. Close the printer. Press down until the cover snaps closed.
Printing a Test (Printer Configuration) Label Printing a Test (Printer Configuration) Label Before you connect the printer to your computer, make sure that the printer is in proper working order. You can do this by printing a configuration status label. 1. Make sure the media is properly loaded and the top cover of the printer is closed. Then, turn the printer power on if you have not already done so.
16 Pre-install Windows® Printer Drivers Pre-install Windows® Printer Drivers Zebra is changing the way you install and use your printer with your Windows based PC systems. We recommend that at minimum, the ZebraDesigner™ Windows® driver be preinstalled to take advantage of the advancements in ease of use and simplicity of the Windows operating systems since the release of Windows XP® SP2.
Pre-install Windows® Printer Drivers Universal Serial Bus (USB) Device Communications The printer is a terminal device (not a host or hub) when using a USB interface. You can refer to the USB Specification for details regarding this interface. Scanners, scales or other data input (terminal) devices must use the serial port (not the USB port) to send data to the printer.
18 Connecting your Printer to a Computer Connecting your Printer to a Computer The printer support a variety of interface options and configurations. These include: Universal Serial Bus (USB) interface, RS232 Serial and Parallel (IEEE 1284.4). • USB, Serial and Parallel The Zebra Setup Utility is designed to assist you with installing these interfaces.
Connecting your Printer to a Computer USB Interface Requirements Universal Serial Bus (version 2.0 compliant) provides a fast interface that is compatible with your existing PC hardware. USB’s “plug and play” design makes installation easy. Multiple printers can share a single USB port/hub. When using a USB cable (not supplied with your printer), verify that the cable or cable packaging bears the “Certified USB™” mark (see below) to guarantee USB 2.0 compliance. .
20 Connecting your Printer to a Computer Serial Communications The GK888 has a DCE serial communication port for hardware compatibility with legacy 888 printers. The required cable must have a nine-pin “D” type (DB-9P) male connector on one end which plugs into the mating (DB-9S) serial port located on the back of the printer. The other end of this signal interface cable connects to a serial port on the host computer. The cable is a Null-Modem (cross-over signal connections) cable.
Connecting your Printer to a Computer EPL Y Command Use the serial port setup (Y) command to change the communications settings on the printer. 1. With the host computer set at the same communications settings as the printer, send the Y command to change the printer to the desired settings. Note: the Y command does not support setting the data flow control, use the Xon/Xoff setting. 2. Change the host computer settings to match the new printer settings.
22 Connecting your Printer to a Computer Parallel Port The required cable must have a 25 pin “D” type (DB-25P) male connector (host) on one end and a Centronics (printer) on the other end (IEEE 1284 A-B parallel interface specification).
After Your Printer is Connected After Your Printer is Connected Now that you have basic communication to your printer, you may want to test printer communications and then install other printer related applications, drivers or utilities. Testing Communications by Printing Verifying the print system’s operation is a relatively simple process. For Windows operating systems, the Zebra Setup Utility or the Windows ‘Printers and Faxes’ Control Panel to access and print a test label.
24 After Your Printer is Connected Notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ _______________________
3 Print Operations This section provides media and print handling, font and language support, and the setup of less common printer configurations. Contents Determining Printer Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Long Term Printer In-activity or Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modes of Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 Determining Printer Configuration Determining Printer Configuration The printer uses a ZPL printer configuration status label to report the printer’s configuration status for both EPL and ZPL operations.The ZPL style label provides a more intuitive and functionally descriptive naming conventions than the EPL style printer status label. Operational status (darkness, speed, media type, etc.), installed printer options (network, interface settings, cutter, etc.
Modes of Printing Modes of Printing You can operate this printer in many different modes and media configurations: • Direct thermal printing (which uses heat sensitive media to print). • Standard Tear-Off mode allows you to tear off each label (or batch print a strip of labels) after it is printed. • Label Dispense Mode: If an optional dispenser is installed, the backing material can be peeled away from the label as it is printed. After this label is removed, the next one is printed.
28 Print Media Types Table 1 • Types of Media Roll and Fanfold Media Media Type Non-Continuous Roll Media How It Looks Description Roll media is wound on a core that can be 0.5 to 1.5 in. (12.7 to 38.1 mm) in diameter. Labels have adhesive backing that sticks them to a liner, and they are separated by gaps, holes, notches, or black marks. Tags are separated by perforations. Individual labels are separated by one or more of the following methods: • Web media separates labels by gaps, holes, or notches.
Replacing Supplies Determining Thermal Media Types Thermal transfer media requires ribbon for printing while direct thermal media does not. To determine if ribbon must be used with a particular media, perform a media scratch test. To perform a media scratch test, complete these steps: 1. Scratch the print surface of the media with a finger nail or pen cap. Press firmly and quickly while dragging it across the media surface.
30 Adjusting the Print Quality Adjusting the Print Quality Print quality is influenced by the heat (density) setting of the printhead, the print speed, and the media in use. Experiment with these settings to find the optimal mix for your application. Print quality can be set with the Zebra Setup Utility’s ‘Configure Print Quality’ routine. Note • Media manufactures may have specific recommendations for speed settings for your printer and the media.
Media Sensing Media Sensing The printer has automatic media sensing capability. The printer is designed to continuously check and adjust media length sensing for minor variations. Once the printer is printing or feeding media, the printer continually checks and adjusts the media sensing to accommodate for minor changes in media parameters from label to label on a roll and from roll to roll of media.
32 Printing on Fan-Fold Media Printing on Fan-Fold Media Printing on fan-fold media requires you to adjust the media roll holders’ stop position. 1. Open the top cover. 2. With a sample of your media, adjust the media roll holders to the width of the media. The hangers should just touch, but not restrict, the edges of the media.Tighten the screw using a small Phillips driver #1.
Printing on Fan-Fold Media 3. With a sample of your media, adjust the guides to the width of the media.The guides should just touch, but not restrict, the edges of the media. 4. Run the media between the media guide and roll holders. 5. Close the top cover. After printing or feeding several labels: If the media does not track down the center (moves from side to side) or the sides of the media (liner, tag, paper, etc.
34 Printing with Externally Mounted Roll Media Printing with Externally Mounted Roll Media The GC420 printer accommodates externally mounted roll media similar to the printer’s support of fan-fold media. The printer requires the media roll and stand combination to have a low initial inertia to pull the media off the roll. Zebra at this time does not offer an external media option for the GC420 printer.
Fonts and Your Printer Fonts and Your Printer The GC420 printer supports your language and font requirements with a variety of internal fonts, on-board font scaling, international font sets and character code page support, Unicode support, and font download. The GC420 printer’s font capabilities are programming language dependent. The EPL™ programming language provides for basic bitmapped fonts and international code pages.
36 Fonts and Your Printer Identifying Fonts in Your Printer Fonts and memory are shared by the programming languages in the printer. Fonts can be loaded in many memory areas in the GC420 printer. ZPL programming can recognize EPL and ZPL fonts. EPL programming can only recognize EPL fonts. See the respective programmer guides for more information on fonts and printer memory. ZPL Fonts: • To manage and download fonts for ZPL print operation, use the Zebra Setup utility or ZebraNet™ Bridge.
Stand Alone Printing Stand Alone Printing Your printer can be configured to work without being attached to a computer. The printer has the ability to automatically run a single label form. One or more downloaded label forms can be accessed and run with a terminal or wedge device or a Zebra® KDU (keyboard display unit) to call a label form. These methods allow the developer to incorporate data input devices, such as scanners or weight scales, to the printer via the serial port.
38 Sending Files to the Printer Sending Files to the Printer Graphics, fonts and programming files can be sent to the printer from the Microsoft Windows operating systems by using the Zebra Setup Utilities (and driver), ZebraNet™ Bridge or Zebra® ZDownloader found on the user's CD or at www.zebra.com. These methods are common for both programming languages and the GC420 printers. Print Meter The GC420 printer has the capability to report printhead maintenance alerts.
4 Printer Options This section covers the common printer options and accessories with brief descriptions and how to get you started using or configuring your printer option or accessory. Contents Label Dispenser Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Zebra® KDU — Printer Accessory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . KDU Plus™ — Printer Accessory . . . . . . . . . . . . . . . . . . . . . . . .
40 Label Dispenser Option Label Dispenser Option The factory installed label dispenser option allows you to print a label with backing (liner/web) being removed from the label as it prints, ready for application. When printing multiple labels, removing the dispensed (peeled) label notifies the printer to print and dispense the next label.
Label Dispenser Option 2. Lift the liner over the top of the printer and open the dispenser door. 3. Insert the label liner between the dispenser door and the printer body.
42 Label Dispenser Option 4. Close the dispenser door. 5. Press the Feed button to advance the media. 6. During the print job, the printer will peel off the backing and present a single label. Take the label from the printer to allow the printer to print the next label. Note: If you did not activate the label taken sensor to detect the removal of the dispensed (peeled) label with software commands, the printer will stack and eject peeled labels.
Zebra® KDU — Printer Accessory Zebra® KDU — Printer Accessory The KDU (keyboard display unit) is a small terminal unit that interfaces with the printer for accessing EPL label forms stored in the printer. The KDU is strictly a terminal and does not have the capability to store data or set up parameters.
44 KDU Plus™ — Printer Accessory KDU Plus™ — Printer Accessory The KDU Plus is a terminal device with memory for storing files and maintaining one or more remote printers. The KDU Plus has a larger laptop style keyboard than the Zebra’s original KDU design.
ZBI 2.0™ — Zebra Basic Interpreter ZBI 2.0™ — Zebra Basic Interpreter Customize and enhance your printer with ZBI 2.0 optional programming language, ZBI 2.0 allows Zebra printers to run applications and take input from scales, scanners and other peripherals—all without a PC or network connection. ZBI 2.0 works with the ZPL printer command language so that printers can understand non-ZPL data streams and convert them into labels.
46 ZBI 2.
5 Maintenance This section provides routine cleaning and maintenance procedures. Contents Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the Printhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Media Path Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Platen Cleaning and Replacement . . . . . . . . . .
48 Cleaning Cleaning When you clean the printer, use one of the following supplies that best suits your needs: Cleaning Supplies Order Quantity Intended Purpose Cleaning pens (105950-035) Set of 12 Clean printhead Cleaning swabs (105909-057) Set of 25 Clean media path, guides and sensors You can obtain cleaning supplies at www.zipzebra.com. The cleaning process takes just a couple of minutes using the steps outlined below.
Cleaning Cleaning the Printhead Always use a new cleaning pen on the printhead (an old pen carries contaminants from its previous uses that may damage the printhead). Caution • The printhead becomes hot while printing. To protect from damaging the printhead and risk of personal injury, avoid touching the printhead. Use only the cleaning pen to perform maintenance. When you load new media, you can also clean the printhead. 1. Rub the cleaning pen across the dark area of the printhead.
50 Cleaning Media Path Considerations Use a cleaning swab to remove debris, dust or crust that has built-up on the holders, guides and media path surfaces. 1. Use the alcohol in the cleaning swab to soak the debris to break up the adhesive. 2. Wipe the ridges to remove accumulated debris. 3. Wipe the inside edges of both edge guides to remove any built-up residue. 4. Wait one minute before closing the printer. Discard the cleaning swab after use.
Cleaning Sensor Cleaning Dust can accumulate on the media sensors. 1. Gently brush away dust; if necessary, use a dry swab to brush away dust. If adhesives or other contaminates remain, use an alcohol moistened swab to break it up. 2. Use a dry swab to remove any residue that may be left from the first cleaning. 3. Repeat steps 1 and 2 as required until all residue and streaks are removed from the sensor. .
52 Cleaning Platen Cleaning and Replacement The standard platen (drive roller) normally does not require cleaning. Paper and liner dust can accumulate without effecting print operations. Contaminates on the platen roller can damage the printhead or cause the media to slip or stick when printing. Adhesive, dirt, general dust, oils and other contaminates should be cleaned immediately off the platen.
Cleaning 5. Install the platen in the printer. Discard the cleaning swabs after use - do not reuse. 6. Make sure the bearings and gear are on the shaft of the platen as shown. 7. Align the platen with the gear to the left and lower it into the printer’s bottom frame. 8. Rotate the tabs back and snap them into place. Allow the printer to dry for one minute before closing the dispenser door, media cover or loading labels.
54 Replacing the Printhead Replacing the Printhead If you need to replace the printhead, read the procedure and review the removal and installation steps before actually replacing the printhead. Caution • Prepare your work area by protecting against static discharge. Your work area must be static-safe and include a properly grounded conductive cushioned mat to hold the printer and a conductive wrist strap for yourself.
Replacing the Printhead 2. Grasp the print head spring and pull it to the left; then, slide it free of the latch frame. 3. Gently pull the wire bundles from the printhead. 4. Use a #1 Phillips driver to loosen the two screws and washers and release the print head from the latch frame and bracket.
56 Replacing the Printhead Printhead Installation 1. Route the print head cables under the latch shaft and plug the printhead cables into the receptacles on the printhead. 2. Hold the printhead against the bracket while replacing the screws and washers. Attach the ground wire using the right screw and washer. Use a #1 Phillips driver to tighten the screws.
Replacing the Printhead 3. Slip the left end of the printhead spring into the left side of the latch bracket; then slide the right end into the other side. The angle of the “V” fits into the indent on the top of the printhead bracket. 4. Align the latch bracket up to the top case and ensure that the cable are not bent or pinched. 5. Replace the four screws that hold the latch bracket to the top case and use a #1 Phillips driver to tighten them. 6.
58 Replacing the Printhead Notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ _______________________________
6 Troubleshooting This section provides information about printer error reporting that you might need for printer troubleshooting. Assorted diagnostic tests are included. Contents Status Light Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status Light Error Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Print Quality Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60 Status Light Descriptions Status Light Descriptions What the Status Light is Telling You P1052685-001 LED Status and Color Printer Status For a Resolution, Refer to Number: Off Off 1 Solid Green On 2 Solid Amber Stopped 3 Flashing Green Normal Operation 4 Flashing Red Stopped 5 Double Flashing Green Paused 6 Flashing Amber Paused 7 Alternately Flashing Green and Red Needs Service 8 Flashing Red, Red and Green Needs Service 9 Flashing Red, Amber Green (* - Do NOT reset o
Status Light Error Resolutions Status Light Error Resolutions The following Status Error Light Resolution numbers correspond to the Status Light Description table on the previous page. Each error number may have one or more resolution to correct that error listed. 1. The printer is not receiving power. • Have you turned on the printer power? • Check power connections from the wall outlet to the power supply, and from the power supply to the printer. See Attaching Power on page 10.
62 Status Light Error Resolutions 6. The printer is paused. • Press the Feed button to resume printing. 7. The printhead is over temperature. • Printing will stop until the printhead cools to an acceptable printing temperature. When it does, the printer will automatically resume operation. 8. FLASH memory is not programmed. • Return the printer to an authorized reseller. 9. The printhead or motor has had a critical failure. • Return the printer to an authorized reseller. 10.
Print Quality Problems Print Quality Problems No print on the label. • The media may not be direct thermal media. See the test procedure Determining Thermal Media Types on page 29. • Is the media loaded correctly? Follow the instructions for Loading Roll Media on page 11 in the Getting Started section. For printing using transfer ribbon, see Printing a Test (Printer Configuration) Label on page 15. The printed image does not look right. • The printhead is dirty. Clean the printhead.
64 Print Quality Problems There are long tracks of missing print (blank vertical lines) on several labels. • The printhead is dirty. Clean the printhead. • The printhead elements are damaged. The printing does not start at the top of the label or misprinting of one to three labels. • The media may not be threaded correctly. Follow the instructions for Loading Roll Media on page 11 in the Getting Started section. • The printer needs to be calibrated.
Print Quality Problems A EPL label format was sent to, but not recognized by, the printer. • Is the printer in pause mode? If so, press the Feed button. • If the printer has label dispensing enabled, the printer may be waiting for the label to be removed. The liner/web must be properly threaded through the label dispenser mechanism (peeler) to correctly operate in label dispense mode, refer to Label Dispenser Option on page 40.
66 Manual Calibration Manual Calibration Manual calibration is recommended whenever you are using pre-printed media or if the printer will not correctly auto calibrate. 1. Make sure media is loaded. 2. Turn on the printer power. 3. Press and hold the Feed button until the green status light flashes once, then twice and then continuing until the flash groups reach the group of seven flashes. Release the Feed button. 4. The printer will set the media sensor for the label backing being used.
Troubleshooting Tests Troubleshooting Tests Printing a Configuration Label To print out a listing of the printer’s current configuration, refer to the one-flash sequence in Feed Button Modes on page 70 in this section. See Appendix: ZPL Configuration on page 81 to interpret the label. Recalibration Recalibrate the printer if it starts to display unusual symptoms, such as skipping labels. Refer to the two-flash sequence in Feed Button Modes on page 70 in this section.
68 Resetting the Factory Default Values Resetting the Factory Default Values Sometimes, resetting the printer to the factory defaults may solve some problems. Refer to the four-flash sequence in Feed Button Modes on page 70 in this section. Communications Diagnostics If there is a problem transferring data between the computer and printer, try putting the printer in the communications diagnostics mode.
Communications Diagnostics The following example of a communications DUMP mode printed out. The printout displays hexadecimal data 00h-FFh (0-255 decimal) with a unique character for each hexadecimal value displayed above the hexadecimal data. The blank lines between the lines of data are where serial port and Bluetooth data handling errors get logged.
70 Feed Button Modes Feed Button Modes Power Off Modes With the printer power off, press and hold the Feed button while you turn on the power. Flash Sequence Amber - Red Flashing Action Firmware Download Mode - The printer starts rapidly flashing red to denote entry into the Firmware Download mode. Releasing the Feed button here will start initializing the printer for download. The printer is ready to start downloading firmware when the status light begins to slowly flash between red and green.
Feed Button Modes Power On Modes With the printer power on and top cover closed, press and hold the Feed button for several seconds. The green status LED will flash a number of times in sequence. The explanation at the right (Action) shows what happens when you release the key after the start specific number of flashes and before the next flash sequence starts. Flash Sequence * * ** Action Configuration Status - Prints a detailed printer configuration status label.
72 Feed Button Modes Notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ _____________________________________
A Appendix: Interface Wiring This section provides printer interface connection information. Contents Universal Serial Bus (USB) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Parallel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Serial Port Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74 Universal Serial Bus (USB) Interface Universal Serial Bus (USB) Interface The figure below displays the cable wiring required to use the printer’s USB interface. The printer requires cable or cable packaging that bears the “Certified USB™” mark to guarantee USB 2.0 compliance. 2 3 1 4 Pin Signal 1 Vbus - N/C 2 D- 3 D+ 4 Ground Shell Shield / Drain Wire For printer supported operating systems and drivers, see the software and documentation CD or visit the Zebra Web site at: http://www.
Parallel Interface Parallel Interface The printer’s parallel interface uses the IEEE 1284-A to 1284-B parallel interface cables. the host connector has a DB-25 pin male connector. The printer connector is a Centronics style connector. HOST DB-25 Pin No. STROBE~ DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 ACK~ BUSY PAPER ERR. SELECT AUTOFD~ ERROR~ N/A N/A N/A SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND SIG. GND SIG.
76 Serial Port Interface Serial Port Interface Pin 1 2 3 4 5 6 7 8 9 Description +5 V @ 0.
B Appendix: Dimensions This section provides external printer dimensions. Contents External GK Printer Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Label Dispenser Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78 External GK Printer Dimensions External GK Printer Dimensions All dimensions are in inches P1052685-001 GC420d™ User Guide 5/23/2012
External GK Printer Dimensions Label Dispenser Option 5/23/2012 GC420d™ User Guide P1052685-001 79
80 External GK Printer Dimensions Notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ ________________________
C Appendix: ZPL Configuration This section provides a basic overview of managing printer configuration, the Configuring Status Printout, and Printer Memory Printouts. Contents Managing Printer Configuration with ZPL Programming . . . . . . . . . . . . . . . . . . . . . . . . . 82 ZPL Configuration Status to Command Cross-reference. . . . . . . . . . . . . . . . . . . . . . . . . 83 Printer Memory Management and Related Status Reports . . . . . . . . . . . . . . . . . . . . . . .
82 Managing Printer Configuration with ZPL Programming Managing Printer Configuration with ZPL Programming The printer is designed to allow you to change printer settings dynamically for fast first label out printing. Printer parameters that are persistent, will be retained for following formats to use.
ZPL Configuration Status to Command Cross-reference ZPL Configuration Status to Command Cross-reference The Printer Configuration Label, shown below, provides a listing of a majority of the configurations settings that can be set by ZPL command. Some printer options and variations will only be displayed if they are present in the printer.
84 ZPL Configuration Status to Command Cross-reference Table 2 • ZPL Commands and Configuration Receipt Callout Cross-Reference Command Listing Name Description ~SD DARKNESS Default: 10.0 ^PR PRINT SPEED Default: 4 IPS / 101.6 mm/s (max.
ZPL Configuration Status to Command Cross-reference The configuration settings listed here resume after the TAKE LABEL sensor value. These listings contain printer features seldom changed from default or provide status information (e.g. Firmware Version).
86 Printer Memory Management and Related Status Reports Printer Memory Management and Related Status Reports To help you manage printer resources, the printer supports a variety format commands to manage memory, transfer objects (between memory areas, import and export), object naming, and provide various printer operating status reports. They are very similar to the old DOS commands like DIR (directory listing) and DEL (delete file).
Printer Memory Management and Related Status Reports Table 4 • Object Management and Status Report Commands Command Name Description ^WD Print Directory Label Prints a list of objects and resident bar codes and fonts in all addressable memory locations ~WC Print Configuration Label Prints a configuration Status Receipt (Label) Same as Feed Button mode one flash routine ^ID Object Delete Deletes objects from printer memory ^TO Transfer Object Used to copy an object or group of objects from one
88 Printer Memory Management and Related Status Reports Notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __
