X Series Specification

X S E R I E S
L O C K F E AT U R E S A N D S P E C I F I C AT I O N S
Lock Features
Elevation Standard StrikeDoor Edge
Door Thickness: 1-3/8” to 1-7/8” doors. Locks for thicker doors
also available. Consult factory.
Backset: 2-3/4” standard. 2-3/8” also available.
Mechanism: Parts constructed of brass or cold formed steel, zinc
plated and dichromated for rust resistance. Springs are stainless
steel. XC Series available with all internal parts of stainless steel or
other nonferrous materials.
Attachment: Locks secured to door by threaded collars. Inner
collar tightened by special wrench furnished with each lock. Outer
rose contains locking plate to prevent unauthorized removal.
Handing: Specify hand of door when ordering. Field reversible.
Cylinders: Drilled with 6-pin chambers, pinned in 5. Pinning in
6 chambers available when specied, at no cost. 7-pin cylinders
available in Hana design. Cylinder assemblies removable to
rekey or change hand of lock. Also available with 6 or 7-pin
interchangeable core cylinders–Elite and Troy designs. Cylinder
housings and plugs machined from solid brass. Springs are
phosphor bronze. Two nickel silver keys furnished standard.
See page 8.
Falcon Lock X Series Specications
Key-in-knob cylindrical locksets shall be Falcon Lock X Series or
equal and meet the following requirements:
• All locksets and latchsets shall meet Grade 1 requirements of
ANSI/BHMA 156.2, Series 4000.
• Locksets and latchsets shall be UL Listed for use on 3 hour A
Label doors.
• Locksets and latchsets shall have 3-1/4” diameter round roses.
• Knobs shall be .050” minimum thickness.
Keyways: “G” keyway standard on standard cylinders. “A” keyway
standard on I/C core cylinders. Also available with other keyways
and some competitor keyways. See pages 9-10.
Trim: Roses are heavy wrought brass, bronze or stainless steel,
installed over wrought steel reinforcing plates. Knobs are brass,
bronze or stainless steel secured by a steel knob retainer which
cannot be depressed when lock has been locked. See individual
designs on pages 5-6 for details.
Latches: 9/16” bolt projection, UL Listed for A-label applications.
Standard latch faceplates 2-1/4” x 1-1/8” with square corners
to accommodate beveled or at front doors. 3/4” projection, UL
Listed latch with 2-3/4” backset also available.
Strikes: 4-7/8” x 1-1/4” ANSI strike with curved lip to meet
ANSI A115.2 standard door frame preparation standard. Consult
Options and Accessories section for other strike sizes and
congurations.
Screws: Furnished with combination wood/machine screws for
use in wood or metal doors and frames.
ANSI/BHMA: Meets ANSI/BHMA A156.2, Series 4000, Grade 1.
UL: 3 hour A label.
• There shall be no exposed screws on trim.
• Locksets and latchsets shall have threaded collars for easy door
thickness adjustment on both sides of lock.
• Cylinders shall have a minimum of 6 active pin chambers and
shall be furnished with 2 nickel silver keys.
• Locksets shall have 6-pin (or 7-pin) interchangeable cores.
Acceptable manufacturer: FALCON LOCK
4
C
L
door, lock & strike are common
Backset (from center of door for beveled stile)
2-3/8”, 2-3/4”
5/32”
2-1/8” Dia.2-15/32”
5/32”
2-1/4”
1-5/8”
1-1/8”
1” Dia.
4-7/8”
3-3/8”
1-1/16”
9/16”
3/8”
4-1/8”
3-1/2”
5/16”
1-1/4”