Specification Sheet

X Series
Features
Door thickness: 1
3
⁄8" to 1
7
⁄8" doors. Locks for thicker doors
also available. Consult factory.
Backset: 2
3
⁄4" standard. 2
3
⁄8" also available.
Mechanism: Parts constructed of brass or cold formed
steel, zinc plated and dichromated for rust resistance.
Springs are stainless steel. XC Series available with all
internal parts of stainless steel or other nonferrous
materials.
Attachment: Locks secured to door by threaded collars.
Inner collar tightened by special wrench furnished with
each lock. Outer rose contains locking plate to prevent
unauthorized removal.
Handing: Specify hand of door when ordering.
Field reversible.
Cylinders: Drilled with 6-pin chambers, pinned in 5. Pinning
in 6 chambers available when specified, at no cost. 7-pin
cylinders available in Hana design. Cylinder assemblies
removable to rekey or change hand of lock. Also available
with 6 or 7-pin interchangeable core cylinders–Elite and
Troy designs. Cylinder housings and plugs machined from
solid brass. Springs are phosphor bronze. Two nickel silver
keys furnished standard. See page 8.
Keyways: “G” keyway standard on standard cylinders. “A”
keyway standard on I/C core cylinders. Also available with
other keyways and some competitor keyways. See pages
9-10.
Trim: Roses are heavy wrought brass, bronze or stainless
steel, installed over wrought steel reinforcing plates. Knobs
are brass, bronze or stainless steel secured by a steel knob
retainer which cannot be depressed when lock has been
locked. See individual designs on pages 5-6 for details.
Latches:
9
⁄16" bolt projection, UL Listed for A-label
applications. Standard latch faceplates 2
1
⁄4" x 1
1
⁄8" with
square corners to accommodate beveled or flat front doors.
3
⁄4" projection, UL Listed latch with 2
3
⁄4" backset also
available.
Strikes: 47⁄8" x 11⁄4" ANSI strike with curved lip to meet
ANSI A115.2 standard door frame preparation standard.
Consult Options and Accessories section for other strike
sizes and configurations.
Screws: Furnished with combination wood/machine
screws for use in wood or metal doors and frames.
ANSI/BHMA: Meets ANSI/BHMA A156.2, Series 4000,
Grade 1.
UL: 3 hour A label.
XSeriesspecications
Key-in-knob cylindrical locksets shall be Falcon
Lock X Series or equal and meet the following
requirements:
§ All locksets and latchsets shall meet Grade 1
requirements of ANSI/BHMA 156.2, Series
4000.
§ Locksets and latchsets shall be UL Listed for
use on 3 hour A label doors.
§ Locksets and latchsets shall have 3
1
⁄4"
diameter round roses.
§ Knobs shall be .050" minimum thickness.
keyway standard on I/C core cylinders. Also
available with other keyways and some
competitor keyways. See pages 9-10.
§ There shall be no exposed screws on trim.
§ Locksets and latchsets shall have threaded
collars for easy door thickness adjustment on
both sides of lock.
§ Cylinders shall have a minimum of 6 active pin
chambers and shall be furnished with 2 nickel
silver keys.
§ Locksets shall have 6-pin (or 7-pin)
interchangeable cores.
Elevation Standard strikeDoor edge
2
3
⁄8",
2
3
⁄4"
5
⁄32"
5
⁄32"
2
15
⁄32"
2
1
⁄8" Dia.
1
1
⁄8"
3
⁄4"
3
3
⁄8"
4
7
⁄8"
1
1
⁄4"
5
⁄16"
3
1
⁄2"
4
1
⁄8"
3
⁄8"
9
⁄16"
1
1
⁄16"
C
L
door, lock & strike are common
Backset (from center of door for beveled stile)
2
1
⁄4"
1
1
⁄8"
1" Dia.
Cylindricallocks
Locks •Falcon•31