Installation Guide

ManualsBrandsFanimation ManualsCeiling Fan Light KitsFour Light Fitter- BL

1. Slide the switch to "RC" if you are using

remote control or wall control with the

light kit. Slide the Switch to "CH" if you

are using pull chain with the light kit.

F8** 4-Light Fitter Installation Instructions

READ AND SAVE THESE INSTRUCTIONS

Weight: 1.87 lbs (0.85 kgs)

NOTE: This ceiling fan light kit is only meant to be used with ceiling fans. Do NOT install as

a light ﬁxture.

WARNING:

To reduce the risk of ﬁre or electric shock, do not use this fan/light kit with any

solid-state speed control device.

To reduce the risk of ﬁre and electric shock, this kight kit

should be used only with the fan model listed below:

CAUTION CAUTION

at the main fuse box to the fan before installing the light

kit.

Fan Model: Windpointe

Series

4. Connect the 2 single-pin connectors

from the low proﬁle light kit to the 2

single-pin connectors from motor

assembly.

Light Fitter

HARDWARE USED:

Glass Attachment

Tool

x 1

7. Securely attach the glass to light ﬁtter

using the glass attachment tool to thread

the glass retainer clockwise into place.

Glass

Retainer

Glass Attachment Tool

Glass

8. Insert light bulbs into sockets.

Socket

Bulb

5. Assemble low proﬁle light kit to motor

assembly with previously removed screws.

6. Remove the glass retainer from the light

ﬁtter and retain the for next step.

Light Fitter

Glass Retainer

2. Remove cover switch housing and

retain the screws for Step 2.

Cover Switch

Housing

Cover Switch

Housing

Light Fitter

3. Remove threaded plug from cover

switch housing and route wires from

light kit through the supplied large

rubber washer, then through the switch

housing and secure cover switch

housing to ﬁtter with lockwasher and

nut provided.

9. Check the operation of the light kit

by gently pulling on the pull chain.

• 1

Pull= On

• 2

Pull= Begins dimming

• 3

Pull= Stops dimming

• 4

Pull= Oﬀ

Summary of content (4 pages)

PAGE 1
F8** 4-Light Fitter Installation Instructions READ AND SAVE THESE INSTRUCTIONS Weight: 1.87 lbs (0.85 kgs) NOTE: This ceiling fan light kit is only meant to be used with ceiling fans. Do NOT install as a light ﬁxture. WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan/light kit with any solid-state speed control device.
PAGE 2
WARNING To reduce the risk of ﬁre, electric shock, and injury to person, must be installed with G4**, G5** and G6** (glass shades) that are marked on F8** to indicate the suitability with this model. Other shades cannot be substituted. WARNING To avoid possible ﬁre or shock, make sure that the electrical wires are completely inside the fan housing and not pinched between the switch cup housing and the switch cup ﬂange.
PAGE 3
F8** IInstrucciones de instalación del ﬁjador de 4 luces LEA Y GUARDE ESTAS INSTRUCCIONES Peso: 0,85 kgs (1.87 lbs) NOTA: Los kits de iluminación del ventilador de techo solo deben utilizarse ventiladores de techo. NO LOS instale como unidad de iluminación. ADVERTENCIA: Para reducir el riesgo de incendio o descarga eléctrica, no use este ventilador / kit de iluminación con ningún dispositivo de control de velocidad de estado sólido. PRECAUCIÓN PRECAUCIÓN Apagar el interruptor de pared no es suﬁciente.
PAGE 4
ADVERTENCIA Para reducir el riesgo de incendio, descarga eléctrica y daño a las personas, debe instalarse con (una tulipa de cristal) G4**,G5** o G6** que esté marcada con F8**, que indica que el modelo es el adecuado. No se pueden sustituir otras pantallas. ADVERTENCIA Para evitar un posible incendio o descarga eléctrica, asegúrese de que los cables eléctricos estén completamente dentro de la carcasa del ventilador y no estén pisados entre la carcasa del conmutador y el borde de la unidad del conmutador.