Installation Guide
This Manual is Designed to Make it as Easy as Possible for You
to Assemble, Install, Operate, and Maintain Your Ceiling Fan
Unpacking Instructions
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
steps have been completed and will be helpful in fi nding your place should you be interrupted.
Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3-
conductor (2-wire with ground) of the following size:
NOTE: Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are missing,
contact your local retailer.
Tools Needed for Assembly Materials
Wire Size A.W.G.Installed Wire Length
14
12
Up to 50 ft.
50 - 100 ft.
NOTE: If you are uncertain of part description, refer to
exploded view illustration. (Figure 1, page 12)
3
1. Check to see that you have received the following
parts:
• Fan Motor Assembly
• Switch Cup/Adapter
Assembly
• Downrod/Hanger Ball
Assembly
• Hanger Bracket
• Ceiling Canopy
• Motor Coupling Cover
• Switch Cup/Adapter
Assembly with Light Fitter
(FP7500RSP4LK only)
• Blade Holder W/Covers
• Glass Bowl
(FP7500RSP4LK only)
• 75W minican Bulb
(FP7500RSP4LK only)
• Blades
Blade Holders with Covers
(not shown –
see parts list for more details)
Hardware Bags
Fan Motor Assembly
Downrod/
Hanger Ball
Assembly
Hanger Bracket
• One Phillips head screwdriver
• One stepladder
• One ¼˝ blade screwdriver
• One wire stripper
• Three wire connectors
(supplied)
Ceiling Canopy
Blade Set (not shown –
see parts list for more details)
• Hardware bags:
– ¼-20 x ½˝
– ¼-20 x 14
(blade
holder to fan motor hub)
screws with lockwashers
– 3/16˝-24 carriage head nut
– 3/16˝-24 x 11mm (Models FP7300
& FP7400) (blade to blade holder)
washer-head screws
– 3/16˝
– 3/16˝-24 x 13mm (Model FP7500RSP4LK)
(blade to blade holder) washer-head screws
-24 x 17mm (Model FP7500)
(blade to blade holder) washer-head
screws
– Phillips screwdriver, 4˝
– Two 5/32˝ threaded rods
– Two 5/32˝ lockwashers
– Two knurled knobs
– Ceiling Support Cable with clamp
– Flat washer
– Lag bolt
– Four wire connectors
– Chain coupler & chain fob
– Balance Kit
– Pull Chain-fan
– Pull Chain-light (Model FP7500RSP4LK only)
Motor Coupling Cover
▲
WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
▲
WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 4). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
Switch Cup Housing/
Adapter Assembly
Switch Cup/Adapter
Assembly with Light Fitter
(FP7500RSP4LK)
Glass Bowl (FP7500RSP4LK)
75-Watt
minican Bulbs
(FP7500RSP4LK)
mm pan head screws
(blade holder to fan motor hub)
with lock washers (Model FP7500RSP4LK)