Ventilation Hood User Manual

ManualsBrandsFantech ManualsVentilation HoodPBW100H

PBW Series

IMPORTANT: PLEASE READ THIS MANUAL BEFORE INSTALLING UNIT

PREMIUM BATH FANS

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

WARNINGS:

DO NOT CONNECT POWER SUPPLY until unit is completely installed.

Make sure electrical service to the fan and light is locked in“OFF” position.

WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS –

OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact your

manufacturer's representative.

b. CAUTION: Before installation, servicing or cleaning unit, switch power off at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning device, such as tag, to the service panel.

c. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable

codes and standards. This unit is only for use in non-fire-rated installations.

d. When cutting or drilling into wall and ceiling, do not damage electrical wiring and other hidden utilities.

e. NEVER place a switch where it can be reached from a tub or shower.

f. If this unit is installed over a tub or shower, it must be connected to a GFCI (Ground Fault Circuit Interrupter) –

protected branch circuit.

g. The combustion airflow needed for safe operation of fuel burning equipment may be affected by this unit’s

operation. Follow the heating equipment manufacturer’s guidelines and safety standards such as those

published by the National Fire Protection association (NFPA), the American Society of Heating, Refrigeration,

and Air Conditioning Engineers (ASHRAE) and the local code authorities.

h. Exhaust fans must always be vented to the outdoors.

CAUTION: "For General Ventilation Use Only. Do Not Use To Exhaust Hazardous Or Explosive Material and Vapors."

CAUTION: BULB USED IN FLUORESCENT MODELS NOT DIMMABLE

CAUTION: USE ONLY FANTECH (MODEL PBB14) FLUORESCENT BULBS AND

PAR16/MR16 GU10 50W MAX. HALOGEN BULBS (FANTECH MODEL PBB50).

Single Grille Units

4" Duct

PBW100

PBW100F

PBW100H

SEVEN-YEAR

WARRANTY

Summary of content (12 pages)

PAGE 1
INSTALLATION, OPERATION AND MAINTENANCE MANUAL PBW Series PREMIUM BATH FANS Single Grille Units 4" Duct EAR Y E N TY S E V RRAN WA PBW100 PBW100F PBW100H IMPORTANT: PLEASE READ THIS MANUAL BEFORE INSTALLING UNIT WARNINGS: DO NOT CONNECT POWER SUPPLY until unit is completely installed. Make sure electrical service to the fan and light is locked in“OFF” position. WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS – OBSERVE THE FOLLOWING: a.
PAGE 2
Planning Your Fan Location Electrical Connection As with any exhaust system, your exhaust fan should be located a minimum of 6 feet horizontally and 8 feet vertically from any fresh air intakes to prevent re-entrainment of exhaust air streams. For example HVAC systems, heat recovery systems, and windows would all be considered fresh air intakes. 1.
PAGE 3
Installation of Ceiling Grille Housing With or Without Light Figure 1 1. Plan Location of Inlet Grilles. Based on the bathroom layout and fixtures, plan the location of the ceiling grilles for the most effective ventilation. 2. Securing the Housing to the Ceiling Joists. NEW CONSTRUCTION Mount housing directly to the ceiling joist using screws and keyhole slots. Locator tabs on housing should be flush with the bottom edge of the ceiling joist for correct positioning of the unit once drywall is installed.
PAGE 4
Housing Dimensions of 4" duct models Housing Dimensions of 6" duct models 9 9⁄16" (243mm) 9 ¹¹⁄₁₆" (246mm) 8" (205mm) 5 ¹³⁄₁₆" (148mm) ⁄16" (8mm) 8 15⁄16" (227mm) 9" (230mm) 5 13 ⁄16" (21mm) 5 5⁄16" (134mm) 6" (150mm) 7 3⁄16" (182.5mm) Seven (7) Year Warranty DURING ENTIRE WARRANTY PERIOD: THE FOLLOWING WARRANTIES DO NOT APPLY: FANTECH will repair or replace any part which has a factory defect in workmanship or material.
PAGE 5
MANUEL D’INSTALLATION, D’OPÉRATION ET D’ENTRETIEN Série PBW VENTILATEURS POUR SALLE DE BAINS PREMIUM Grille simple Conduit de 4 po NTIES A R GA 7 AN DE PBW100 PBW100F PBW100H IMPORTANT : VEUILLEZ LIRE CE MANUEL AVANT L’INSTALLATION AVERTISSMENTS : NE PAS BRANCHER LE COURANT ÉLECTRIQUE avant que l’appareil soit complètement installé. Assurez-vous que le courant électrique au ventilateur et lumière soit débranché « OFF ».
PAGE 6
Planifier l’emplacement du ventilateur Branchement électrique Comme tout autre système d’évacuation, votre ventilateur devrait être situé à un minimum de 6 pieds horizontalement et 8 pieds verticalement de toutes les entrées d’air frais afin de prévenir la réintégration des courants d’air vicié. Par exemple, les systèmes HVAC, les systèmes récupérateurs de chaleur et les fenêtres sont tous considérés comme étant des entrées d’air frais. 1.
PAGE 7
Installation du boîtier avec ou sans éclairage Figure 1 1. Planifiez l'endroit pour la grille D'après votre salle de bain et ses installations, planifiez l'endroit où vous installerez vos grilles de plafond pour une ventilation efficace. 2. Fixez le boîtier à la poutrelle du plafond. NOUVELLE CONSTRUCTION Fixez le boîtier directement sur la poutre du plafond avec les vis. Les languettes sur le boîtier devraient être au même niveau que le côté inférieur de la poutrelle du plafond (Figure 1).
PAGE 8
Dimension du boîtier des modèles à conduit de 4 po 9 ⁄ po (243mm) 9 Dimension du boîtier des modèles à conduit de 6 po 16 9 ¹¹⁄₁₆ po (246mm) 8 po (205mm) ⁄16 po (8mm) 8 15⁄16 po (227mm) 5 ¹³⁄₁₆ po (148mm) 9 po (230mm) 5 13 ⁄16 po (21mm) 5 5⁄16 po (134mm) 6 po (150mm) 7 3⁄16 po (182.5mm) Garantie de sept (7) ans PENDANT LA PÉRIODE DE LA GARANTIE : FANTECH réparera ou remplacera toute composante ayant un défaut manufacturier.
PAGE 9
MANUAL DE INSTALACIÓN, FUNCIONAMIENTO Y MANTENIMIENTO Serie PBW VENTILADORES PARA BAÑO PREMIUM Unidades de Reja Solas 4" Conducto NTÍAS A R GA AÑO DE 7 PBW100 PBW100F PBW100H IMPORTANTE: FAVOR DE LEER ESTE MANUAL ANTES DE INSTALAR LA UNIDAD ADVERTENCIAS: NO CONECTE LA ALIMENTACIÓN ELÉCTRICA hasta que la unidad quede totalmente instalada. Asegúrese de que el servicio eléctrico del ventilador y la luz esté bloqueado en posición de “OFF” (apagado).
PAGE 10
Planificación de la ubicación del extractor Conexión eléctrica Al igual que con todo sistema de extracción, el extractor de aire debe instalarse a una distancia mínima de 6 pies horizontalmente y 8 pies verticalmente de toda entrada de aire fresco a fin de impedir el rearrastre hacia el interior de corrientes del aire extraído. Por ejemplo, los sistemas HVAC, los sistemas de recuperación de calor y las ventanas, todos ellos se deben considerar como entradas de aire fresco. 1.
PAGE 11
Instalación de la caja de rejilla de techo con o sin luz Figura 1 1. Planee la ubicación de las rejillas de admisión. Con base en el diseño y el mobiliario del baño, planee la ubicación de las rejillas del techo para obtener la ventilación más efectiva. 2. Fije la caja a las viguetas del techo. CONSTRUCCIÓN NUEVA Fije la caja directamente en la vigueta del techo con tornillos y las ranuras de alineación.
PAGE 12
Dimensiones de la caja de los modelos de conductos de 4" Dimensiones de la caja de los modelos de conductos de 6" 9 9⁄16" (243mm) 9 ¹¹⁄₁₆" (246mm) 8" (205mm) 5 ¹³⁄₁₆" (148mm) ⁄16" (8mm) 8 15⁄16" (227mm) 9" (230mm) 5 13 ⁄16" (21mm) 5 5⁄16" (134mm) 6" (150mm) 7 3⁄16" (182.5mm) Garantía de siete (7) años DURANTE TODO EL PERÍODO DE GARANTÍA: LAS SIGUIENTES GARANTÍAS NO PROCEDEN: FANTECH reparará o reemplazará cualquier pieza que presente defectos de fábrica, ya sea de manufactura o del material.