User Manual i33V&i33VF Software Version: 2.4.
Directory Directory....................................................................................................................................................... １１ 1 Picture ......................................................................................................................................................... ３３ 2 Table ............................................................................................................................................................
10.6 System >> Auto Provision ................................................................................................................ 19 10.7 System >> FDMS ............................................................................................................................. 22 10.8 System >> Tools ............................................................................................................................... 22 10.9 Network >> Basic ...........................................
1 ３ Picture Picture 1 - Panel ................................................................................................................................. 6 Picture 2 - Quickly setting .................................................................................................................. 7 Picture 3 - WEB Login ....................................................................................................................... 8 Picture 4 - SIP Line Configuration .................
2 Table Table 1 - Common command mode ................................................................................................... 4 Table 2 - Icon Status ........................................................................................................................... 4 Table 3 - Panel introduction ............................................................................................................... 6 Table 4 - Intercom .............................................................
3 Safety Instruction Please read the following safety notices before installing or using this unit. They are crucial for the safe and reliable operation of the device. Please use the external power supply that is included in the package. Other power supply may cause damage to the phone and cause noise issue. Before using the external power supply in the package, please check the home power voltage. Inappropriate power voltage may cause fire and damage. Please do not damage the power cord.
4 Overview i33V &i33VF is an access control product with LCD specially developed for the needs of industry users on the basis of VoIP telephone technology for more than ten years. The standard IP/RTP protocol is used for voice transmission, and the RTSP is used for video transmission.
5 Install Guide 5.1 Use POE or external Power Adapter i33V&i33VF, supports two power supply modes, power supply from external power adapter or over Ethernet (POE) complied switch. POE power supply saves the space and cost of providing the device additional power outlet. With a POE switch, the device can be powered through a single Ethernet cable which is also used for data transmission.
6 Appendix Table 6.1 Common command mode Table 1 - Common command mode Action Description IP Broadcast under In standby mode, long presse ‘#’ standby mode In standby mode, long press ‘C’ for 10 seconds, there will be a toot sound. Within 5 seconds, press ‘C’ three times quickly to switch the Switch mode network network mode. Network state in static or PPPoE mode will be switched to DHCP mode; If the network is in DHCP mode, it will switch to static IP 192.168.1.128.
Icon Description Connected to the TR069 Password error 5 Icon Description Not connected to the TR069，flashing Invalid card
7 Basic Introduction 7.1 Panel Overview Picture 1 - Panel Table 3 - Panel introduction Number Name Description 1 Video signal acquisition and transmission 2、3 IP Camera IR LED/ Photoresistor 4 Speaker Play sound 5 LCD Display status and prompts 6 Numeric keypad Password and dialing 7 Function key Watch video clearly even in weak light environment C: Dial Key, Enter the number and press C to dialing out.
K: Password mode,“K password # ” B: Backspace Key, Enter the number and press B to delete 8 MIC Sound collecting 9 RFID area Open the door with card 7.2 Quick Setting Before proceeding with this step, make sure your Internet broadband connection is working properly and connecting to the network hardware. The default factory mode of i33V&i33VF is DHCP. IP address can be viewed by. Open the iDoorPhone Network Scanner. Press the Refresh button to search the device and find the IP address.
Picture 3 - WEB Login The username and password should be entered into the web page correctly. The default username and password are "admin". For the specific details of the operation of the web page, please refer to 10 Web Configurations 7.4 SIP Configurations At least one SIP line should be configured properly to enable the telephony service. The line configuration is like a virtualized SIM card.
7.5 Door opening operation Unlock the door in the following eight ways: 1) Open the door with the local password, and press “K key + local door open password +#” to open the door. 2) The access control helps to call owner, and the owner enters the remote opening password to open the door.
8 Basic Function 8.1 Making Calls In standby mode, you can make a call by: Enter the number and press the “C” Press “C” to enter the number, then press “C” IP direct dialing in standby: Set to the length of the IP address as the length of the received number Set the programmable button "*" key dial mode to DTMF input In standby mode, enter xxx*xxx*xxx*xxx and press “C” to call out. 8.
Picture 5 - Enable Auto Answer Auto Answer mode： Disable：Turn off the automatic answer function, the device has a call, ring, will not time out to answer automatically. Line1：Line 1 has an automatic call timeout. Line2：Line 2 has an automatic call timeout. Line1 and Line2：Line 1 and line 2 have an automatic call timeout. Lines and IP Call：Line and IP direct dial call timeout automatically answer.
Turn on/off the interruption free method for the specific line of the device, as follows: Web interface: enter [EGS Setting] >> [Features], set the do not disturb type to Line, enter [Line] >> [SIP], choose a Line and enter [Line] >> [Advanced settings], Enable DND. Picture 7 - Enable DND 8.6 Call Waiting Enable call waiting: new calls can be accepted during a call.
9 Advance Function 9.1 Intercom The equipment can answer intercom calls automatically. Picture 9 - WEB Intercom Table 4 - Intercom Parameters Description Enable Intercom Mute Enable mute during intercom mode Enable Intercom Ringing If the incoming call is intercom call, the device plays the intercom tone. 9.2 MCAST This feature allows user to make some kind of broadcast call to people who are in multicast group.
Picture 10 - Multicast Settings Table 5 - MCAST Parameters on Web Parameters Description Enable Auto Mcast The multicast configuration information is sent through Sip Notify signaling. After receiving the information, the device will be configured to the system for multicast monitoring or cancel multicast monitoring in the system.
Press the DSSKY of Multicast Key which you set. Receive end will receive multicast call and play multicast automatically. 9.3 SIP Hotspot SIP hotspot is a simple but practical function. With simple configurations, the SIP hotspot function can implement group ringing. SIP accounts can be expanded. Set a Phone set as a SIP hotspot and other phone sets (B and C) as SIP hotspot clients. When somebody calls the phone set A, then the phone sets A, B, and C will all ring.
Picture 11 - SIP hotspot client configuration As the hotspot server, the default extension number is 0. When the phone is used as the client, the extension number is increased from 1, you can view the extension number through the [SIP Hotspot] page. Call extension number: The hotspot server and the client can dial each other through the extension number. For example, extension 1 dials extension 0.
10 Web Configurations 10.1Web Page Authentication Users can log into the device's web page to manage user device information and operate the device. Users must provide the correct user name and password to log in. If the password is entered incorrectly three times, it will be locked and can be entered again after 5 minutes.
10.3System >> Account Picture 12 - WEB Account Settings On this page the user can change the password for the login page. Users with administrator rights can also add or delete users, manage users, and set permissions and passwords for new users. 10.4System >> Configurations On this page, users with administrator privileges can view, export, or import the phone configuration, or restore the phone to factory Settings.
“.txt”. (note: profile export requires administrator privileges) Import Configurations Import the configuration file of Settings. The device will restart automatically after successful import, and the configuration will take effect after restart Reset Phone The phone data will be cleared, including configuration and database tables. 10.5System >> Upgrade Picture 14 - Upgrade Settings Upgrade the software version of the device, and upgrade to the new version through the webpage.
Fanvil devices support SIP PnP, DHCP options, Static provision, TR069. If all of the 4 methods are enabled, the priority from high to low as below: PNP>DHCP>TR069> Static Provisioning Transferring protocol: FTP、 TFTP、 HTTP、 HTTPS Details refer to Fanvil Auto Provision http://www.fanvil.com/Uploads/Temp/download/20180920/5ba3816f8d5f0.pdf Table 7 - Auto Provision Parameters Auto Provision Parameters Description Basic settings Show the current config file’s version.
Check Times downloaded 5 times. Enable Server When the feature is enable, if the configuration of server is changed, Digest phone will download and update. DHCP Option Option Value Custom Option Value Enable DHCP Option 120 The equipment supports configuration from Option 43, Option 66, or a Custom DHCP option. It may also be disabled. Custom option number. Must be from 128 to 254. Set the SIP server address through DHCP option 120. SIP Plug and Play (PnP) Whether enable PnP or not.
ACS Server Type There are 2 options Serve type, common and CTC. ACS Server URL ACS server address ACS User ACS server username (up to is 59 character) ACS Password ACS server password (up to is 59 character) TR069 Auto Login Enable/Disable TR069 Auto Login. STUN server address Enable the STUN Enter the STUN address Enable the STUN 10.
Picture 17 - System Tools Syslog：When enabled, set the syslog software address, and log information of the device will be recorded in the syslog software during operation. If there is any problem, log information can be analyzed by Fanvil technical support.
Picture 18 - Basic Network Settings Table 9 - Basic setting parameters Field Name Explanation Network Status IP Subnet mask Default gateway MAC MAC Time stamp The current IP address of the equipment The current Subnet Mask The current Gateway IP address The MAC address of the equipment Get the MAC address of time. Settings Select the appropriate network mode. The equipment supports three network modes: Static IP DHCP PPPoE Network parameters must be entered manually and will not be changed.
by Primary DNS Server Secondary DNS Server Enter the server address of the Primary DNS. Enter the server address of the Secondary DNS. attention： 1）After setting the parameters, click【submit】to take effect. 2）If you change the IP operation, the web page will no longer respond, at this time should be entered in the address bar new IP to connect to the device.
10.10 Network >> VPN Picture 19 - Network VPN Settings Virtual Private Network (VPN) is a technology to allow device to create a tunneling connection to a server and becomes part of the server’s network. The network transmission of the device may be routed through the VPN server. For some users, especially enterprise users, a VPN connection might be required to be established before activate a line registration. The device supports two VPN modes, Layer 2 Transportation Protocol (L2TP) and OpenVPN.
When the VPN connection established, the VPN IP Address should be displayed in the VPN status. There may be some delay of the connection establishment. User may need to refresh the page to update the status. Once the VPN is configured, the device will try to connect with the VPN automatically when the device boots up every time until user disable it. Sometimes, if the VPN connection does not establish immediately, user may try to reboot the device and check if VPN connection established after reboot.
Picture 21 - Web Filter Table Add and remove accessible IP segments; Configure the starting IP address within the start IP, end the IP address within the end IP, and click [Add] to submit to take effect. A large network segment can be set, or it can be divided into several network segments to add. When deleting, select the initial IP of the network segment to be deleted from the drop-down menu, and then click [Delete] to take effect.
Picture 22 - SIP Line Configuration Configure the service configuration for the wire on this page. Table 10 - Line configuration on the web page SIP Field Name Explanation Basic Settings (Choose the SIP line to configured) Line Status line status, user has to refresh the page manually. Username Enter the username of the service account. Display name Enter the display name to be sent in a call request.
Outbound proxy port Enter the outbound proxy port, default is 5060 Realm Enter the SIP domain if requested by the service provider Codecs Settings Set the priority and availability of the codecs by adding or remove them from the list.
After closing the grab packet, you can see that the DSP is sendonly and the hold is sendrecv Use Quote in Display Name Specific Server Type Registration Expiration Whether to add quote in display name Set the line to collaborate with specific server type Set the SIP expiration interval Use VPN Set the line to use VPN restrict route Use STUN Set the line to use STUN for NAT traversal Convert URI Convert not digit and alphabet characters to %hh hex code Set the DTMF sending mode, there are four types:
update received after the timeout period Session Timeout Set the session timer timeout period Enable Rport Set the line to add rport in SIP headers Enable PRACK Set the line to support PRACK SIP message Enable DNS SRV Set the line to use DNS SRV which will resolve the FQDN in proxy server into a service list Auto Change Port Enable/Disable Auto Change Port Keep Authentication Keep the authentication parameters from previous authentication Using TCP protocol to guarantee usability of transport for
Picture 24 - Basic Line Settings Table 11 - Basic Line Settings Field Name Explanation SIP Settings Local SIP Port Set the local SIP port used to send/receive SIP messages. Registration Failure Set the retry interval of SIP REGISTRATION when registration Retry Interval failed. Enable Strict UA Match Enable or disable Strict UA Match Field Name Explanation STUN Settings Server Address STUN Server IP address Server Port STUN Server Port – Default is 3478. Binding Period SIP Waiting Time 10.
10.15 EGS Setting >> Features Picture 25 - ESG Feature Settings Table 12 - ESG Feature Parameters EGS Features Setting (Only for Door phone) Field Name Explanation Basic Settings Monostable: there is only one fixed action status for door unlocking. Switch Mode Bistable: there are two actions and statuses, door unlocking and door locking.
status. After changed, the status would be kept. Initial Value is Monostable Switch-On Duration Enable Card Reader Door unlocking time for Monostable mode only. If the time is up, the door would be locked automatically. Initial Value is 5 seconds. Enable or disable card reader for RFID cards. Set ID card stats: Normal: This is the work mode, after the slot card can to open the door. Card Reader Card Issuing: This is the issuing mode, after the slot card can to add ID Working Mode cards.
status. After changed, the status would be kept. Initial Value is Monostable Remote Code Check Length The remote access code length would be restricted with it. If the input access code length is matched with it, system would check it immediately. Initial Value is 4. Close keyboard input; The key pattern Only the Password； Only the Dial； Dial and Password； Disable: after disable, cannot use the authentication code to open the Local authentication door.
Timeout Dial Fixed Length to Send Configure to enable/disable fixed-length automatic dial-out numbers. Configure the receiving number length; default is 4. After the user dials Send length the 4-digit number, the device will automatically call out the 4-digit number. Dial Number Voice Configure to enable/disable dial-up voice prompts, which are disabled Play by default. System Language Language for configuring voice prompts.
10.16 EGS Setting & Intercom Setting >> Audio Picture 26 - EGS Audio Settings Table 13 - EGS Audio Parameters Field Name Explanation Audio Settings Codec Setting Select enabled or disabled audio codec: G.711A/U,G.722,G.723,G.729, G.726-16,G726-24,G726-32,G.726-40, ILBC,AMR,AMR-WB, opus DTMF Payload Type Setting DTMF payload type, the value range must be 96~127. Default Ring Type Configure the default ring tone. If no special ringtone is set for the caller number, the default ringtone will be used.
closing, and other custom prompt sound Field Name Explanation Audio Settings Sound Select Opening prompting Can be set to default and voice prompt Closing prompting Can be set to default and voice prompt Issuing prompting Can be set to default and voice prompt Revoking prompting Can be set to default and voice prompt Open Failed prompting Can be set to default and voice prompt Sound Delete Sound Delete Upgraded ringtones are displayed in the delete list, which can be optionally deleted 10.
Picture 27 - EGS Video Settings Table 14 - EGS Video Parameters Camera connection Settings Field Name Explanation Camera status: When the device is restarted, the camera status shows Camera status whether it is currently available. and number of The maximum number of accesses, the maximum number of main code visits streams, the maximum number of subcode streams and the number of uses.
horizontal scroll Vertical Flip The video is flipped horizontally IR Swap IR-cut filter switch In the Day / Night mode Auto option, the color switching black and white DNC Threshold threshold is set Set the video color to black and white threshold in the day and night mode selection auto mode Backlight Compensation In front of a very strong background light can see people or objects clearly AutoFill In the environment changes in light and shade, the higher the sensitivity the Sensitivity faster t
Main profile/High profile: see the H264 nal unit payload as Main profile/High profile "Default" reverts to factory video configuration, and "submit" saves Settings Advanced Settings Sendonly: establish video call, and the SDP packet in the invite packet is Video Direction Sendonly; Sendrecv: to create a call, the SDP package in the invite package is Sendrecv RTSP Over TCP The RTSP goes over the TCP protocol H.264 Payload Set the h. 264 Payload type. The range is between 96 and 127.
10.19 EGS Setting & Intercom Setting >> Action URL Table 16 - Action URL Settings Action URL Event Settings URL for various actions performed by the phone. These actions are recorded and sent as xml files to the server. Sample format is http://InternalServer /FileName.xml Note! The operation URL is used by the IPPBX system to submit device events. Please refer to the details Fanvil Action URL。 http://www.fanvil.com.cn/Uploads/Temp/download/20190122/5c46dd1ad4635.pdf 10.
Month End The DST end month Week End The DST end week Weekday End The DST end weekday Hour End The DST end hour Manual Time Settings Manual Time Settings 10.21 Set the time by hand, which needs to disable SNTP service first EGS Settings >> Trusted Certificates Upload and delete uploaded certificates on the certificate management page . Picture 28 - Certificate Management 10.22 EGS Settings >> Device Certificates Select the device certificate as the default and custom certificate.
10.23 EGS Access Picture 30 - EGS Management Table 18 - EGS Manage Parameters EGS Access Field Name Explanation Import Access Table Click the to choose to import remote access list file (access List.csv) and then clicking can batch import remote access rule. Access Table According to entrance guard access rules have been added, you can choose single or multiple rules on this list to delete operation. Click " " to export the saved access list.
rules on this list to delete operation. Name(necessary) User name When the speed dial is input, it will be mapped to the corresponding Location number. The outgoing order is: the owner number (priority), the forwarding number will be called if the owner number is busy or no answer. ID RFID card number. You can manually fill in the first 10 digits of the card number or select the existing card number. e.g.
You should input the top 10 digits of RFID card numbers. for Add Admin Card example, 0004111806, then select the type of admin card and click . Type：Open/ Add/ Delete. Open：Super administrator card, the device can open the door through the super management card when the device cannot open due to the software processing error or configuration read failure.
Name Door Open Log Result Show the results door open history ( Succeeded or Failed) Time The door open time. Access If the door was opened by swipe card or remote unlocking door, the device Name would display remote access name. Open type: 1. Local, 2. Remote, 3. Card Note: there are three kinds of card feedback results. Type Temporary Card (only added the card number, without adding other rules ) Valid Card (added access rules) Illegal Card (the card not added in the door phone database) 10.
Check Delay Lock Status Door Status Check Back Door Close/Open Door Close/Open Door Lock Control Door Lock Execute a door lock to open or close the door Action Door Open/Close Once: perform door opening action, and will be closed automatically Open mode when timeout. Continue: perform the door opening action, the door will not be closed automatically and need to closed manually when timeout.
Tamper Alarm Settings Alarm When detected someone tampering the equipment, the alarm signal will be command sent to the corresponding server Reset When the equipment receives the command of reset from server, the command equipment will stop alarm Reset Alerting Reset to resume and stop ringtone playback Status Ring Type Ringtone can be set to none / preset Server Settings Send message to the server when the alarm is triggered.
11 Trouble Shooting When the phone can’t be used normally, the user can try the following methods to restore normal operation of the phone or collect relevant information and send a problem report to Fanvil technical support mailbox. 11.1Get Device System Information Users can get information by pressing the [Menu] >> [Status] option in the phone.The following information will be provided: The network information Equipment information (model, software and hardware version), etc. 11.
when operation finished. The network packets of the device during the period have been dumped to the saved file.Users can analyze packets or send them to the Fanvil support mailbox. 11.5Common Trouble Cases Table 22 - Trouble Cases Trouble cases Solution Device could not boot up 1. The device is powered by external power supply via power adapter or PoE switch.
