DVD-22/ DVD-22T Single-DIN A/V Multimedia Source Touch Sensor DVD/CD/MP3/MP4 AM/FM Radio Built-in TV tuner Owner’s Manual Take the time to read through this owner’s manual. Familiarity with installation and operation procedures will help you obtain the best Performance from your new DVD-receiver.
Table of Contents Table of Contents.......................................................................................................................1 Important Safeguards.................................................................................................................2 Accessories .......................................................................................................................3 Installation/Un-Installation ...........................................................
Important Safeguards z Using the device at temperature below -10℃ may cause the breakage of the device. BEFORE USING PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED TEMPERATURE! z Read carefully through this manual to familiarize yourself with this high-quality sound system. z Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. z When replacing the fuse, be sure to use one with an identical amperage rating.
Accessories Package contains the following accessories for installation and operation of the unit.
Installation/Un-Installation First complete the electrical connections, and then check them for correctness. Installation This unit can be installed in any dashboard having an opening as shown on the picture. The dashboard should be 4.75 – 5.56 mm thick in order to be able to support the unit. 1. Insert mounting collar into the dashboard, and bend the mounting tabs out with a screwdriver. Make sure that lock lever（※）is flush with the mounting collar (not projecting outward). 2. Secure the rear of the unit.
Wiring Connections Make sure you have good chassis ground. A good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the vehicle’s metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust, or dirt for a good electrical connection. Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2.
Caution: Do not interchange the connection of the wiring!!! For some car models you may need to modify wiring of the supplied power cord. Contact your authorized car dealer before installing this unit. Remark: When you back a car, screen display switch to Rear Camera automatically Detachable Control Panel Detaching the control panel z z z Turn the Power off. Press OPEN button release the panel. Pull the panel out.
Panel Controls 1. Power/Mute 2. BAND 3. PREVIOUS 4. VOL + 5. NEXT 6. DISP 7. AS/PS 8. LCD 9. IR sensor 10. OPEN 11.MODE. 12.OK 13.VOL- 14. PRESET 1/play pause 15. PRESET 2./RPT 16. PRESET 3./INT 17. PRESET 4/RDM 18. PRESET 5/STOP 19. PRESET 6/MENU 20.AUX IN JACK 21.USB SLOT 22.SD SLOT 23.EJECT 24.DISC SLOT 25.
IR Remote Control 1. MODE 2. POWER 3. BND/RDM 4. ENTER 5. Cursor / / / 6. STEREO/MONO 7. LOC/ PROG 8. P.SCN/RPT 9. SEEK-/ 10. LOUD 11. OSD 12. STOP/ PBC 13. Digit 0-9 14. 15. MUTE 16. MENU 17. SUB-T 18. SETUP 19. ANGLE 20. INT 21. VOL+ 22. A-B/ZOOM 23. SEL 24. SEEK+/ 25. VOL26. AUDIO/ GOTO REPLACING THE BATTERY Remote Control comes with a CR-2025 Lithium Battery included. 1. Remove the Battery Holder from the back of the Remote Control. 2.
General Operations Reset the Unit In case the unit is malfunctioned or need to reset to factory default setting, press RESET button in inner panel then the unit will be reset. Power on/off Press POWER key button to turn on the unit. Long press POWER key on front panel or press POWER button on RC to power off the unit. Under Power on mode, short press comes in mute.
Digital Tuner Band selection Press MODE button to select the RADIO mode. Press the BAND button to select the desired band: FM1=> FM2 => FM3 => AM1=>AM2 STEREO/MONO In FM mode, press SETREO/MONO button on remote control to select stereo or mono sound reception. Manual/ automatic tuning Manual tuning: press the / buttons on remote control(or on the front panel ) and hold for 2 seconds to enter the manual tuning mode.
SD/MMC Cards & USB Operations USB Flash Memory To play MP3/ MP4/ WMA files from a USB flash memory, insert a USB flash memory into the USB port on the right side of the unit. The unit will start playing MP3/MP4/ WMA files on the USB flash memory automatically. Or press the MODE button to select USB after pressing POWER button to turn on the unit.
Repeat Press the RPT button on remote control or the panel for RPT1 (repeat the current playing file) => RPT ALL (repeat all folders) => RPT folder (repeat current folder) => RPT OFF. Repeat A-B Function 1. Press A-B button on the remote at the starting point of the section you want to repeat (point A). 2. Press A-B button again at the ending point of the section you want to repeat (point B). Section A-B repeating starts. 3. Press A-B button again to cancel the A-B repeat function.
Discs operations Glossary PBC (Play Back Control) Play Back Control is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs contained PBC, it can playback interactive software with the menu displayed on TV. And if the disc contains still images, it can playback high definition of still image. Title The title is the important part of DVD disc. The memory volume of the disc is rather big, that makes possible to record several films on one disc.
Playing/pausing To ensure good system performance, wait until the unit finishes reading the disc information before proceeding. Press the PLAY/ PAUSE button to start/ pause the playback. In pause mode press it again to resume the playback. Stop During playback press the STOP button on the RC or on the panel. Playback will be stopped. Press the PLAY/ PAUSE button again to start playback from the position at which it was stopped. If the disc is removed, the resume function is cancelled.
PBC (Playback Control) function (for VCD only) If you insert a VCD with PBC, playback starts from the beginning of the 1st track automatically. 1. Long press PBC/STOP button to activate interactive menu on screen during playback. 2. If the menu consists of titles, you can select a desired one using the digit 0-9 buttons. 3. The VCD starts playing the selected title automatically or press ENTER button to confirm the selected track for playback. MENU function (for DVD only) 1.
MP3 overview Notes on MP3: z MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard. z This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs. z The unit can read MP3 files written in the format compliant with ISO 9660. However it does not support the MP3 data written by the method of packet write. z The unit can not read an MP3 file that has a file extension other than “.mp3”. z If you play a non- MP3 file that has the “.
Setup Menu • Press SETUP button to enter the system settings main menu; • Press cursor / buttons to move along icons on the top navigation bar on settings main menu. Select one of the setup pages: General, Speaker, Downmix, Audio; • Press cursor / buttons to choose a setting or return to the Setup Page; button to enter the highlighted setting; • Press cursor • Press ENTER button on remote contro confirm your setting.
Dolby settings Menu entry Dual mono With this menu item you can select the type of Left and Right channel audio output. Stereo is normal Stereo, Mono L is all sound on the Left Audio output, Mono R is all sound on the Right channel. The “Mix Mono” function only works when a DVD is being played in DTS 5.1 mode. Video settings Menu entry This serves to set the sharpness of the Sharpness image (high / medium / low). This serves to set Brightness the brightness of the image (- 20 to + 20).
Preference settings Menu entry TV Type Audio Subtitle Disc Menu Parental Password Default Function This setting enables the selection of the appropriate TV standard. PAL is the customary standard in Europe. NTSC is the customary standard in the US and Japan. Only select the MULTI option if your TV can play back both formats. Here the output signal is automatically adjusted to the standard of the inserted DVD.
Note: If you have forgotten your changed password, you can set a new one at any time by entering the factory default password 1369.. Factory default settings (“RESET“) By using the reset function, the device can be changed back to the factory default settings. To use the reset function, please press the button REL on the device. Now the operating unit can be carefully detached towards the front and left. Now press the RESET button on the device with a thin, sharp object.
Other Functions Subwoofer Connect the subwoofer to the unit using sub output (see electrical diagram). Press SEL button, choose expert and set subwoofer ON to enable subwoofer. Anti-theft system Remove the panel 1. Press the PWR button to turn the power off. 2. Press OPEN button to detach the panel. 3. Pull the panel out. 4. Place the panel into the case and take it with you when you leave the car. Remove the unit 1. Remove the panel and the trim plate. 2.
Note on Discs Only use groundless loudspeakers. Use only loudspeakers of minimal 40 Watt, using fewer watts may result in damaging your loud speakers at higher volumes. Use 4~8 Ω (Ohm impedance) loudspeakers only; using higher or lesser impedance may damage the unit. Do not use 3-cable loudspeakers and do not connect the loudspeakers minus to the car body. (GND). using a BTL circuit and each loudspeaker must be connected with insulated cables according the diagram.
Troubleshooting guide Symptom Cause Solution General No power The car ignition is not on. The fuse is blown. If the power supply is properly connected to the car accessory switch the ignition key to “ACC”. Replace the fuse. Disc Disc cannot be loaded. Presence of disc inside the player Remove the disc in the player then put a new upward. Disc cannot be read. No sound The operation keys do not work. Sound skips. The radio does not work, the radio station automatic selection does not work.
Specification General Power supply: Current consumption: Maximum power output: Compatible formats: Dimensions (W x D x H) / weight: ESP function: Working temperature range: FM Stereo Radio Frequency range: Usable sensitivity: Preset memory stations: AM section Frequency range: Preset memory stations: Audio specification Maximum output: Frequency response: S/N ratio(A-vtd): DSP sound effect: Line out 12 V DC max.
