DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
Fargo Integrator Workstation User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Fargo Integrator Workstation User Guide (Rev. 1.1), property of FARGO Electronics, Incorporated Copyright 2002, 2003, 2004, 2005, 2006 by FARGO Electronics, Incorporated. All rights reserved. Printed in the United States of America.
RESTRICTED USE ONLY Fargo Electronics, Inc.
RESTRICTED USE ONLY Fargo Electronics, Inc.
RESTRICTED USE ONLY Fargo Electronics, Inc. Section 1: Specifications The purpose of this section to provide the User with specific information on the Regulatory Compliances and Agency Listings for the Integrator Workstation User Guide (Rev. 1.1). Regulatory Compliances Term Description CSA The Printer manufacturer has been authorized by UL to represent the ribbon programmer as CSA Certified under CSA Standard C22.2 No. 60950-1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Agency Listings Term Description EMC Standards CE, FCC, CRC c1374, EN 55022 Class A, FCC Class A, EN 55024, EN61000-3-2 and EN61000-3-3. Safety Standards UL IEC 60950-1 (2001), CSA C22.2 No. 60950-1 and UL-GS (EN 60950-1:2001). FCC Rules This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
RESTRICTED USE ONLY Fargo Electronics, Inc. Safety Messages (review carefully) Symbol Critical Instructions for Safety purposes Danger: Failure to follow these installation guidelines can result in death or serious injury. Information that raises potential safety issues is indicated by a warning symbol (as shown to the below). Caution: To prevent personal injury, refer to the following safety messages before performing an operation preceded by this symbol.
RESTRICTED USE ONLY Fargo Electronics, Inc. Section 2: Integrator Workstation Overview Program Group Overview Enrollment for Import Suppliers and Integrator The Integrator Workstation program is a combination of hardware and software that is used by Fargo and integrators to enroll end users in the SecureMark program and program ribbons for End User SecureMark Printers. (Note: Each SecureMark Ribbon contains integrator code that uniquely identifies the ribbon.
RESTRICTED USE ONLY Fargo Electronics, Inc. Integrator Workstation Program Groups The three program groups in the Integrator Workstation are Integrator Supplies, Database Administration and System Administration, as shown below. Additional capabilities are provided within the program or programs under a respective program group. These capabilities are described in Sections 3 to 5 of this User guide.
RESTRICTED USE ONLY Fargo Electronics, Inc. Integrator Workstation Program Descriptions Printer Ribbon Programming Program The Ribbon Programming capability is used by integrators to create SecureMark media for end users. See Ribbon Programming Program. Program Group: Integrator Supplies Integrator Administration Program The Integrator Administration program is used by integrators to view the information that Fargo has on record for them. See Integrator Administration Program.
RESTRICTED USE ONLY Fargo Electronics, Inc. Integrator Workstation Program Descriptions (continued) Database Backup Program The Database Backup program is used to provide Fargo with an archive of all the end user and printer registration information. See Database Backup Program. Program Group: Database Administration Workstation users Program The User Administration program is used to register new users for the Integrator Workstation and define their level of access. See Workstation users Program.
RESTRICTED USE ONLY Fargo Electronics, Inc. Logging onto the Integrator Workstation Each Integrator Workstation User is assigned a User ID and Password so that only authorized users are able to use the program. Roles are used to limit access to specific functions within the Integrator Workstation. The assigned roles for the Integrator Workstation are as follows: System Administrator: This role allows access to all programs in all program groups.
RESTRICTED USE ONLY Fargo Electronics, Inc. Using the File and Help Dropdown Menus Using the File Dropdown Menu Menu option Description Close Select the Close option to close the currently active program on the screen. Log Off Select the Log Off option to close all active programs and log the current User out of the Integrator Workstation. Exit Select the Exit option to close the Integrator Workstation Fargo Integrator Workstation User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Using the Help Dropdown Menu Menu option Description Help Select the Help option to view this Users Guide. About Select the About option to view version information for the individual programs. Fargo Integrator Workstation User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.0), property of FARGO Electronics, Incorporated Copyright 2002, 2003, 2004, 2005, 2006 by FARGO Electronics, Incorporated. All rights reserved. Printed in the United States of America.
RESTRICTED USE ONLY Fargo Electronics, Inc.
RESTRICTED USE ONLY Fargo Electronics, Inc. Password Control Application _______________________________________________________ 3-2 Print Security Suite – Main Window __________________________________________________ 3-3 SecureMark Media ________________________________________________________________ 3-3 Section 4: Setup and Installation Procedures ______________Error! Bookmark not defined. Table of Contents ____________________________________________ Error! Bookmark not defined.
RESTRICTED USE ONLY Fargo Electronics, Inc. Resolving the Print Ribbon Out Error Message ___________________ Error! Bookmark not defined. Resolving the Ribbon Jam/Broken Error Message _________________ Error! Bookmark not defined. Resolving the Wrong Print Ribbon Error Message ________________ Error! Bookmark not defined. Resolving the Unknown Ribbon Type Error Message ______________ Error! Bookmark not defined. Resolving the Headlift Error Message __________________________ Error! Bookmark not defined.
RESTRICTED USE ONLY Fargo Electronics, Inc. Using the Split 1 Set of Ribbon Panels option ____________________ Error! Bookmark not defined. Using the Print Back Side First option __________________________ Error! Bookmark not defined. Using the Print on Back Side Only option _______________________ Error! Bookmark not defined. Using the Rotate Front by 180 Degrees option____________________ Error! Bookmark not defined.
RESTRICTED USE ONLY Fargo Electronics, Inc. Selecting the Full Card with the K Panel Resin tab ________________ Error! Bookmark not defined. Selecting the Defined Area(s) with the K Panel Resin tab ___________ Error! Bookmark not defined. Selecting the Undefined Area(s) with the K Panel Resin tab _________ Error! Bookmark not defined. Defining the Area to activate the Card Grid ______________________ Error! Bookmark not defined.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Sample String _________________________________ Error! Bookmark not defined. Reviewing the ASCII Code and Character Table __________________ Error! Bookmark not defined. Section 10: Packing the DTC550 Card Printer _____________Error! Bookmark not defined. Section 11: Board Level Diagnostics _____________________Error! Bookmark not defined. Board Errors ________________________________________________ Error! Bookmark not defined.
RESTRICTED USE ONLY Fargo Electronics, Inc. Contacting Fargo Technical Support______________________________ Error! Bookmark not defined. Reading the Serial Numbers on a Fargo Printer _____________________ Error! Bookmark not defined. Finding out when a Fargo Card Printer was manufactured __________ Error! Bookmark not defined. Reviewing Example No. 1: Serial Number 80453289______________ Error! Bookmark not defined. Reviewing Example No.
RESTRICTED USE ONLY Fargo Electronics, Inc. Section 1: Introduction How to use the manual The DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.0) is designed to provide Installers and Technicians with quick, efficient lookup of related procedures, components and terms. The manual can be used effectively either in soft or hard copy, depending on the preference of the Installer or Technician.
RESTRICTED USE ONLY Fargo Electronics, Inc. DTC550 Direct to Card Printer/Encoder Overview Reviewing the DTC550 Block Diagram DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing DTC550 Sequence of Operations The following sequence describes a DTC550 doing a dual sided full color print job with magnetic encoding. Step Process 1 The File information is received from the PC. 2 The Flipper Stepper activates and rotates the Flipper Table until the Flipper Home Sensor is activated.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing DTC550 Sequence of Operations (continued) Step Process 12 The Card is centered on the Flipper Table based on input from the Flipper Table Card Sensor. 13 The Flipper Stepper rotates the Flipper Table a specific number of steps (based on the Flipper Offset setting) to the Home the Flipper Table. 14 The Card Feed Motor feeds the Card to the Print TOF Sensor. 15 The Ribbon Drives turn ON and move. All Stop.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing DTC550 Boot up Sequence Step Process 1 The Printer checks the installed memory in the Printer. 2 The Printers Firmware is initialized. 3 The Headlift Motor activates and cycles the Printhead one full rotation. 4 The Encoding Feed Motor activates and the Magnetic TOF Sensor checks for the presence of a Card. 5 The Hopper Transport Motor activates until the Hopper Position Sensor detects a change in state.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Lamination Module Sequence of Operations The LAM sequence of operations begins after printing has occurred with the Card Printer. Step Process 1 The card is fed onto the Lamination Module Flipper Table. 2 The card is fed to the Card Position Sensor. 3 The Lamination Ribbon Motor begins cycling until the Upper Lamination Sensor detects the mark. 4 The Card Feed Motor activates to center the card on the Platen Roller.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Lamination Module Sequence of Operations (continued) Step Process 6 The Card Feed Motor and the Lamination Ribbon Motor activate for the length of the card. 7 The Lamination Roller Lift Motor cycles until Lamination Roller Lift Sensor detects state change. 8 The card is fed back to the Flipper Table. 9 The Flipper Table Clutch engages. 10 The Flipper Table Motor activates until the Card is inverted based on the Flipper offset setting.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Lamination Module Boot up Sequence Step Process 1 The Lamination Headlift turns until head up position is returned from Headlift Sensor. 2 The Lamination Ribbon motor activates to determine the presence of a roll of lamination. 3 The Lamination Flipper table homes itself. 4 The Card sensor checks for the presence of a card and ejects it if found. DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Section 2: Specifications The purpose of this section is to provide the User with specific information on the Regulatory Compliances, Agency Listings, Technical Specifications and Functional Specifications for the DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.0). Regulatory Compliances Term Description CSA (cUL) The Printer manufacturer has been authorized by UL to represent the Card Printer as CSA Certified under CSA Standard C22.2 (No. 609501).
RESTRICTED USE ONLY Fargo Electronics, Inc. Agency Listings Term Description EMC Standards CE, FCC, CRC c1374, EN 55022 Class A, FCC Class A, EN 55024, EN61000-3-2 and EN61000-3-3. Safety Standards UL IEC 60950-1 (2001), CSA C22.2 No. 60950-1 and EN 609501:2001. FCC Rules This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
RESTRICTED USE ONLY Fargo Electronics, Inc. Safety Messages (review carefully) Symbol Critical Instructions for Safety purposes Danger: Failure to follow these installation guidelines can result in death or serious injury. Information that raises potential safety issues is indicated by a warning symbol (as shown to the below). Caution: To prevent personal injury, refer to the following safety messages before performing an operation preceded by this symbol.
RESTRICTED USE ONLY Fargo Electronics, Inc. Technical Specifications Term Description Accepted Standard Card Size CR-79 Adhesive Back: 3.303 in. x 2.051 in. (83.9mm x 52.1mm) (cannot be laminated with DTC550-LC) Accepted Card Thickness .020 in. (20 mil) to .050 in. (50 mil) (.254mm to 1.27mm); unless laminating. CR-80: 3.375 in. x 2.125 in. (85.6mm x 54mm) (corresponds to ID1) Continued on the next page DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Technical Specifications (continued) Term Description Accepted Card Types Prox (125 kHz): HID Proximity Cards (read only) Contactless (13.
RESTRICTED USE ONLY Fargo Electronics, Inc. Technical Specifications (continued) Term Description Card Cleaning Removable card cleaning cartridge with replaceable cleaning roller. Colors Up to 16.7 million colors and 256 shades per pixel. Dimensions DTC550: 10.75 in. H x 18.5 in. W x 11 in. D (273mm x 470mm x 279mmD). DTC550-LC: 10.75 in. H x 30.5 in. W x 11 in. D (273mm x 775mm x 279mmD). LC Module: 10.
RESTRICTED USE ONLY Fargo Electronics, Inc. Technical Specifications (continued) Term Description Fargo Certified Supplies Fargo Card Printer/Encoder require highly specialized media to function properly. To maximize printed card quality, printhead life and Printer/encoder reliability, use only Fargo Certified Supplies. Fargo warranties are void, where not prohibited by law, when non-Fargo Certified Supplies are used. Fonts TrueType fonts are available via the Windows driver.
RESTRICTED USE ONLY Fargo Electronics, Inc. Technical Specifications (continued) Term Description Print Speed – Batch Mode K: 7.
RESTRICTED USE ONLY Fargo Electronics, Inc.
RESTRICTED USE ONLY Fargo Electronics, Inc. Technical Specifications (continued) Term Description Supply Frequency 50 Hz/60 Hz. System Requirements Windows® 2000 with Service Pack 4, Windows® XP with Service Pack 2 and Windows® Server 2003; x86 300 MHz computer with 64 MB of RAM or higher, 200 MB free hard disk space or higher, USB 1.1 Warranty Printer (One year); optional Extended Warranty Program (U.S. only) Printhead (One year), unlimited pass with UltraCard Cards Weight DTC550: 20 lbs. (9.
RESTRICTED USE ONLY Fargo Electronics, Inc. Functional Specifications The Card Printer utilizes two different, yet closely related printing technologies to achieve its direct-to-card print quality for Dye-Sublimation and resin thermal transfer. The Card Printer will print from any IBM-PC® or compatible running Windows 2000 or Windows XP.
RESTRICTED USE ONLY Fargo Electronics, Inc. Functional Specifications (continued) Function Description Resin Thermal Transfer Resin Thermal Transfer is the print method the Printer uses to print sharp black text and crisp bar codes that can be read by both infrared and visiblelight bar code scanners. Like Dye-Sublimation, this process uses the same thermal Printhead to transfer color to a card from a resin-only Print Ribbon or the resin black (K) panel of a full color Print Ribbon.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components - Descriptions Component Description Card Thickness Adjustment Lever Adjusts the Printer to feed varying card thicknesses. DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Descriptions (continued) Component Description Card Cleaning Cartridge Automatically cleans cards for higher print quality. (Note: Replace this roller with every ribbon or as needed.) DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Descriptions (continued) Component Description Card Input Hopper Load blank cards into this Dual Input Hopper. DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Descriptions (continued) Component Description Card Output Hopper Stores printed cards; up to 100, 30 mil cards. DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Descriptions (continued) Component Description Card Supply Window Check the current card supply at-a-glance, without having to open the Card Hopper Door. Card Input Hopper Lock This lock allows you to lock the Card Input Hopper Door to help prevent the theft of blank cards. Exception Card Slot Insert a single exception card into this slot if you would like to print onto a card other than those loaded in the Card Input Hopper.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Descriptions (continued) Component Description Printhead This Print Station component actually does the printing. (Note: This component is fragile and must not be bumped or touched with anything other than a cleaning pen.) DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Descriptions (continued) Component Description Power Switch This switch turns the Printer power ON and OFF. Power Port This port connects to the (included) power supply. Securing Latches These latches lock the Print Station securely in place when closed. Softkey Buttons The button function is displayed above the button. The buttons change depending upon the Printer's mode of operation.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Descriptions (continued) Refer to the previous table. DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: LCD and Softkey Control Pad The Printer provides a four line, eighty (80) character LCD display that communicates helpful information about the Printer's operation. The top three lines of the LCD display will always be used to communicate print status, error messages and menu options. The bottom line of the LCD display will always be used to communicate the current function of the Printer's softkey buttons.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: LCD and Softkey Control Pad (continued) Component Description Ready/Printer Open Screens Once the Printer has finished its system check and with the Print and Transfer Stations closed, the Printer will display READY to indicate that the Printer is ready for operation. (Note: The Printer will stay in this mode until it receives a print job or it is turned OFF.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: LCD and Softkey Control Pad (continued) Component Description The Cancel button Use this button to cancel print jobs and reset the Printer for the next print job. Pause button This Cancel function will ask if you wish to cancel just the individual job or all jobs in the queue. You may also resume the current job by pressing NO. Use this button to pause the Printer at any time during operation.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: LCD and Softkey Control Pad (continued) Component Description LED light This light works in conjunction with the Printer's LCD display to help communicate the Printer's current status. (Note: It is especially effective when the User is too far away from the Printer to read the LCD display.) See the descriptions for Error Screens and Attention Screens after this LED Light display for more detail on the Printer's LCD display.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: LCD and Softkey Control Pad (continued) Component Description Error Screens (see previous section) Your Printer is capable of communicating two similar yet different types of message screens: The first is called an ERROR screen. This screen appears if an error occurs and will completely stop Printer operation. In this case, the LCD will display ERROR on the first line and a brief description of the error on the second line.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Print Ribbons The Card Printer utilizes both Dye-Sublimation and/or resin thermal transfer methods to print images directly onto blank cards. Since the Dye-Sublimation and the resin thermal transfer print methods (each) provide their own unique benefits, Print Ribbons are available in resinonly, Dye-Sublimation-only and combination Dye-Sublimation/resin versions. This letter code indicates the type of Ribbon panel used with each Ribbon.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Resin-Only Print Ribbons Resin-only Print Ribbons consist of a continuous roll of a single resin color. No protective overlay panel (O) is provided since resin images do not require the protection of such an overlay.. Type Description Standard Resin Black (K) (provides 3,000 prints) This Ribbon provides high resin durability ideal for most general-purpose monochrome ID card applications.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Dye-Sublimation Print Ribbons Note that the Printer requires both specialized and authorized Print Ribbons in order to print and function properly. Step 1 Procedure Do not run the cards with a contaminated, dull or uneven surface through the Printer. Caution: Printing onto such cards will ultimately lead to poor print quality and will greatly reduce the life of the Printhead.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Dye-Sublimation/Resin Print Ribbons Type Description DyeSublimation/ resin Print Ribbon The Dye-Sublimation/resin Print Ribbon combines the yellow (Y), magenta (M) and cyan (C) dye-sublimation panels with a resin black (K) panel. By combining both types of Ribbon panels, this Ribbon can be used to print full-color, photo-quality images with the dye-sublimation panels along with sharp, black text and bar codes with the resin black panel.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Blank Cards Caution: Never run cards with a contaminated, dull or uneven surface through the Printer. Printing cards on this surface can lead to poor print quality and can greatly reduce the life of the Printhead. Always store the card stock in its original packaging or in a clean, dust-free container. Do not print onto cards that have been dropped or soiled.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Blank Cards (continued) Type Description UltraCard Stock Due to the importance of using high-quality blank cards, a factory-approved card stock called UltraCard™ is available and recommended for best results. UltraCard stock has a glossy PVC laminate on top and bottom and is optically inspected to provide the cleanest, most scratch and debrisreduced cards possible. Two types of these cards are available: UltraCard and UltraCard III.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Upgraded 81754 PVC Cards The upgraded 81754 PVC cards are designed for a sharper card image quality and for reduced debris and defects on Fargo Card Printers. Carefully read these detailed notes and instructions before applying this information to your Fargo Printer or Printers. Technician Note 1: The new card lot number starts at Lot # 2010104 with date codes that started on 04/01/2003.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the upgraded 81754 PVC Cards (continued) Follow these two (2) instructions below: 1. Instruction for new 81754 PVC card stock: Increase the Printer Driver’s Dye-Sub Intensity to print with the new 81754 PVC card stock on Fargo Card Printers (S/N A319 and older). See the chart provided below. See the appropriate Fargo service documents for specific Printer Driver instructions.
RESTRICTED USE ONLY Fargo Electronics, Inc. Printer Components: Card Input and Output Hoppers Type Description Card Input Hopper The Card Input Hopper is where cards are initially loaded for printing, as shown below. The Printer's Hopper provides a large door that opens up wide to make card loading simple and closes securely to help protect the card stock. (Note: The Printer will hold a maximum of 100 cards in each Card Input Hopper, based on a standard 30 mil. card thickness.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Card Lamination Module Danger: The Printer’s Lamination Roller can reach temperatures exceeding 350° F (175° C). Use extreme caution when operating the Laminator. Never touch the Lamination Roller unless the Printer has been turned off for at least 20 to 30 minutes. Select Printer models support the attachment of an optional Card Lamination Module.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Card Lamination Module (continued) Here is another display of the Card Lamination Module. DTC550 Direct to Card Printer/Encoder User Guide (Rev. 1.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Lamination Top Cover and Station Component Description Cross Reference Lamination Top Cover Opens to allow access to the Lamination Station, overlaminate and card path. See the Loading the Overlaminate procedure. Lamination Station Transfers overlaminates onto cards via its heated lamination Roller. The Lamination Station must be closed in order for the Printer to begin laminating. See the Loading the Overlaminate.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Securing Latches and Lamination LED light Component Description Cross Reference Securing Latches Locks the Lamination Station securely in place when closed. See the Using the Lamination tab (only with Card Lamination Module) procedure. Lamination LED light The Lamination LED light works in conjunction with the Printer's LCD display to help communicate the Printer's current status. The following explains how to interpret the LED light.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Cancel button Component Description Cross Reference Cancel Button The Cancel button serves to cancel the current lamination job and reset the Card Lamination Module for the next lamination job. See Card Lamination Module. If a card is left within the Lamination Module after a print job is canceled, it will automatically be ejected into the Rejection Card Hopper.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Resume (pause) button Component Description Cross Reference Resume (pause) button Press the Resume button to resume operation after an error condition is cleared. See the Using the Lamination tab (only with Card Lamination Module) procedure. If an error occurs, the Lamination Module's LED will flash and the Printer's LCD will report the specific error.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Rejection Card Hopper and Card Output Hopper Component Description Cross Reference Rejection Card Hopper The Rejection Card Hopper helps to separate potentially bad cards from a stack of good cards, which it ejects into the Card Output Hopper. See the Using the Lamination tab (only with Card Lamination Module) procedure.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Module and Printer interaction Term Description Cross Reference Module and Printer interaction The Card Lamination Module works in conjunction with the Printer to apply a variety of different overlaminates to printed cards, providing increased card durability and security. See the Using the Lamination tab (only with Card Lamination Module) procedure.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Module and LCD display interaction Term Description Cross Reference Module and LCD display interaction For ease of operation, the Card Lamination Module works in tandem with the Printer's LCD display to communicate status message such as when an error occurs or when it is time to replace the overlaminate material. See the Using the Lamination tab (only with Card Lamination Module) procedure.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Module’s Programmed Default Temperature Term Description Programmed Upon initial power up, the Lamination Default Module is programmed to heat the Temperature Lamination Roller up to its default temperature. Reference See the Using the Lamination tab (only with Card Lamination Module) procedure. Target Temperature: If a print job is sent while the Lamination Module is heating up, the Printer's LCD display will read Laminator Warming.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Laminator Temperature Adjustment Term Description Laminator To change the temperature of the Temperature Laminator, adjust its temperature through Adjustment the Lamination tab within the Printer Driver setup window. See the Using the Lamination tab (only with Card Lamination Module) procedure.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Overlaminates IMPORTANT! Fargo Card Printers require highly specialized overlaminates to function properly. To maximize Printer life, reliability, printed card quality and durability, you must use only Fargo Certified Supplies. For this reason, the Fargo warranty is void, where not prohibited by law, if you use non-Fargo Certified Supplies. To order additional materials, please contact the authorized reseller.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the CR-90 or CR-100 Patch Size Term Description Cross Reference CR-90 or CR-100 PolyGuard overlaminate is available in a standard CR-80 patch size as well as a CR90 and CR-100 patch size for laminating oversized CR-90 or CR-100 cards. (Note: Thermal Transfer Film overlaminate will accommodate CR-80 and CR-90 card sizes, but is not recommended for CR-100 cards.) See the Loading the Overlaminate procedure.
RESTRICTED USE ONLY Fargo Electronics, Inc. Reviewing the Visual Security Solutions VeriMarkTM Cards - 2-D holographic foil application VeriMarkTM Cards are a low cost, customized 2-D holographic foil application, that is made in two steps. The first step is to emboss a base foil 1.9 cm (L) x 1.3 cm (H) onto the surface of a blank white card. The second step is debossing a custom made dye into the surface of the base foil leaving a customized image, logo or text provided by the customer.
RESTRICTED USE ONLY Fargo Electronics, Inc. Visual Security Card Stock - Tolerances Tolerance of base foil placement will equal +/- .010" from the nearest edges of the card Tolerance of layered foil will equal +/- .010" VeriMarkTM - Application Specifications VeriMarkTM foils will cover a dimensional area of 1.9 cm length x 1.3 cm height.
RESTRICTED USE ONLY Fargo Electronics, Inc. In order to enter the Fargo Secure Print Security Suite, an administrator must enter a password and select a Printer. The Fargo Secure Print Security Suite consists of the products listed below. Refer to the Fargo Secure Print Security Suite User Guide for more detailed procedures. Print Notification Application The Print Notification Application gives the User the ability to send an e-mail to an administrator when the Printer used during unauthorized hours.
RESTRICTED USE ONLY Fargo Electronics, Inc. Print Security Suite – Main Window Here are the icons for the five (5) applications within the Print Security Suite. See the Functional Specification section and the Software Instructions section in this same document for more detailed information on these five (5) applications. Caution: Be sure and save your work in the Printer Security Suite. By selecting Save All on the File dropdown menu, you can save your work on all active applications.