Installation Instructions

CUSTOMER SERVICE
Chemque Inc. T: 1-800-268-6111 OR [phone]
266 Humberline Dr., F: [phone]
Rexdale, Ontario M9W 5X1 [e-mail]
Canada www.Fast2K.com / www.chemque.com
LIMITED WARRANTY: Chemque warrants the performance of this product, provided it is properly stored and applied. If not satised, submit claim in writing to Chem-
que’s address below, and Chemque will, at its option, replace or refund the purchase price of this product if proved defective. User shall determine the suitability of this
product for the intended use and assume all risks and liability in connection within.
THIS IS THE SOLE AND EXCLUSIVE REMEDY AND SOLE AND EXCLUSIVE LIABILITY OF CHEMQUE FOR DEFECTS IN OR FAILURE OF THIS PRODUCT. THIS WARRANTY IS
IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, STATUTORY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
INSTRUCTIONS:
1. NOTICE. Fast 2K is ideal to ll voids around a fence or mail box post and is NOT intended for applications where it would be subjected
to load-bearing, such as slabs.
2. Please ensure you have the following materials required for application:
- Knife or scissors
- An object with a round hard edge such as a step stool or small table.
- Protective chemical resistant gloves (included with Fast 2K)
- Safety glasses or goggles
3. Always keep Fast 2K bags at 22°C - 25°C (72°F - 77°F) for at least 2 hours before using. Product from bags kept at lower
temperatures will take longer to react, expand and set and will produce less volume. Product from bags kept at higher temperatures will react,
expand and set faster, lowering the working time and producing a higher volume, weaker composite.
4. Make sure that there is no standing water in the hole. It’s a good idea to put 3-4” of gravel at bottom of hole. Set and brace (or hold)
the post inside the hole, making sure it is leveled before mixing the bag.
5. CAUTION! Although this bag may have a tear notch, always have scissors or a knife next to the hole ready to cut the
corner of the bag IMMEDIATELY AFTER mixing is complete as indicated in steps 6, 7 & 8 and in case the tear notch does not exist
or malfunctions. Failure to cut the bag immediately after mixing will result in the composite expanding inside the bag which may cause the bag
to rupture, contents to spray out and personal injury as well as property damage to occur. Mixing must be complete and bag must be cut in less
than one minute from removing outer black clip.
6. To release outer black clip that divides the bag, grasp the outer edge of the bag on both ends length-
wise and pull bag outwards with moderate force until black clip eases off. CAUTION! DO NOT PULL THE BAG
SHARPLY AND DO NOT SLIDE THE CLIP OFF THE BAG as it may tear apart the bag, causing the contents to
spray out and personal injury as well as property damage to occur.
7. Rub the bag with moderate force for 30 seconds along a round hard edge by forcing material inside
the bag from one end to the other with each stroke (“shoe shining” technique). CAUTION! DO NOT EXCEED
MIXING TIME AND NEVER ALLOW THE COMPOSITE TO START EXPANDING INSIDE THE BAG AS BAG
MAY RUPTURE, CAUSING CONTENTS TO SPRAY OUT AND PERSONAL INJURY AS WELL AS PROPERTY
DAMAGE TO OCCUR.
8. CUT ONE OF THE BAG CORNERS IMMEDIATELY AFTER MIXING AND POUR MIXED COMPOS-
ITE INTO THE HOLE BEFORE EXPANSION STARTS. Tip: To avoid spillage, prior to cutting the bag corner,
gently push the product out of that corner rst. CAUTION! Cut the bag open immediately if composite
starts to expand in the bag. EXPANSION INSIDE THE BAG WILL CAUSE THE BAG TO RUPTURE, CONTENTS TO
SPRAY OUT AND PERSONAL INJURY AS WELL AS PROPERTY DAMAGE TO OCCUR.
9. Empty the bag into the hole, wetting the sides of the post at or slightly above ground level. Fast 2K is
waterproof after it cures and will help protect posts from rotting. Therefore it is even more benecial to have Fast
2K lling the hole all the way to the top by pouring some extra Fast 2K and/or by setting the post in the narrowest
possible hole. After initial pour, roll the bag to completely empty the content out into the hole. NOTICE. Do not
move the post up or down.
10. Adjust / level the post side to side if necessary within the next 10 seconds. Do not move the post after
expansion starts. In approximately 3-4 minutes Fast 2K should expand up to 3-5 inches (8-13 cm) from the top of
the hole. There should be no need to brace or hold the post 1-2 minutes after that.
11. In approximately 15-30 minutes Fast 2K will already be quite hard and can be topped up with dirt. Wait
for approximately 2 hours for the product to completely set before installing the fence or gate.
NOTES:
A. If necessary, a hole can always be topped up with more composite. When topping up, wait for at least
5 minutes after a bag poured previously has completely expanded or it is cured to the touch. If too much Fast 2K
has been poured into the hole and there is an overow above ground, wait for 10 - 15 minutes after pouring the
bag, or the composite is tack free, and remove the excess by carefully cutting it with a handsaw or a utility knife,
for example. Be careful as this may damage the post surface.
B. CLEAN UP: Using a soft cloth and mineral spirits , carefully remove any Fast 2K smudges from surfaces of the post that are visible (above
ground) as well as from tools before Fast 2K dries. After Fast 2K dries, it can only be removed by cutting it with a handsaw or a utility knife,
for example. Be careful as this may damage the post surface.
-2-
Step 6
Step 7
Step 8
SERVICE CLIENTÉLE
Chemque Inc. T: 1-800-268-6111 OU [phone]
266 Humberline Dr., F: [phone]
Rexdale, Ontario M9W 5X1 [e-mail]
Canada www.Vite2K.com / www.Fast2K.com / www.chemque.com