FAST & FLUID MANAGEMENT AT550 ENGLISH User manual
© Fast & Fluid Management, AT550 p2
© Fast & Fluid Management, AT550 Table of Contents AT550 Manual EU Declaration of conformity Introduction & Warranty Explanation of picture Safety Instructions Installation Operation Maintenance Troubleshooting Technical specifications Contributing to the Protection of the Environment 4 4 5 6 7 8 10 14 16 17 18 p3
© Fast & Fluid Management, AT550 AT550 Manual EU Declaration of conformity Fast & Fluid Management, the Netherlands A Unit of IDEX Corporation Hub van Doorneweg 31 2171 KZ Sassenheim, the Netherlands declare that: Produkt: Automatic dispensers Model: Accutinter Types: AT550 are in compliance with the following directives: Machinery Directive 98/37/EC Low Voltage Directive 73/23/EEC Electromagnetic Compatibility Directive 89/336/EEC according to the following harm onized standards: EN 292-1, EN 292-2,
© Fast & Fluid Management, AT550 Introduction & Warranty Introduction By selecting a Fast & Fluid Management Color Dispenser you have opted for a produc t which is the result of intensive research. Top-quality c omponents, craftsm anship and a modern ergonomic design all serve to guarantee a long service life and a high degree of user friendliness.
© Fast & Fluid Management, AT550 Explanation of picture Dispenser Dispenser module Canister module Service panels 3. Electrical parts Nozzle closure Nozzle guard 1. 2.
© Fast & Fluid Management, AT550 Safety Instructions General safety instructions Attention! Before installing the equipment and setting it in operation, please read the instructions for use carefully. This is safer for yourself and prevents unnecessary damage to the machine. The manufacturer accepts no liability if the instructions below are not followed: 1. 2. 3. 4. 5. 6. 7. 8. If a machine has been damaged (during transport, for example), do not attem pt to set it in operation.
© Fast & Fluid Management, AT550 Installation A - Installing the dispenser Step 1 - Unpack the machine > > Remove the two bottom panels to access the screws that are connected to the crate. Remove the cardboard box and remove the plastic foil around the machine. Place the crate near the place of installation. Be careful not to damage the body and surfaces of your AT550 with any tools while unpacking it. > Remove the bolt's on both sides.
© Fast & Fluid Management, AT550 B - Installing the computer and software Step 1 - Place and connect computer to dispenser > > Monitor and keyboard can be placed on top of the dispenser Computer can be plac ed in lower compartment. Remove the bottom panel. Step 2 - Install dispenser software on computer > Connect dispenser USB cable and mouse, keyboard and other appliances to design-nated computer ports. > Install all necessary software provided by software supplier.
© Fast & Fluid Management, AT550 Operation A - First time operation Step 1 - Switching ON the dispenser & computer > The machine is automatically switched on when the power connector at the back of the dispenser is plugged into a 220V or 100V-110V wall socket. * We recommend to keep the machine on at all times. > The dispense abort switch must be released. The green button only swithces internal wall socket.
© Fast & Fluid Management, AT550 Step 3 - Fill the nozzle closure. > Lift the switch plate and move it towards the machine. > Lower the switch plate under the dispense head. Use the appropriate c ommand from the dispenser software to open the nozzle closure. Remove the c up holder. Moisturise the cup with water or cleaning fluid until the pad is soaked. Replace the cup holder in its original position. Replace the switch plate. Use only cleaning fluids recommended by your paint supplier.
© Fast & Fluid Management, AT550 Step 4 - Fill the canisters with colourant > Check your software manual for filling sequence. Run software purge program until the air is removed from system.
© Fast & Fluid Management, AT550 B - Dispensing Step 1 - Bring can to correct position > Place the can at the right place of the can table. > Hold the can table and unloc k the index pin with the foot pedal. Lift the can table until the can is in reach of the can sensor. The can should be just below the switch plate. Release the index pin. Gently release the can table.
© Fast & Fluid Management, AT550 Maintenance A - Daily maintenance Clean the nozzle closure, refill canisters and run morning program > Replace the pad. Refill the cup with water or c leaning fluid until the pad is soaked. > Fill canisters if level is low and update levels in software. Stir colorant beforehand. Start software morning program to purge valves and clean nozzles. Check your software manual for details. Use only cleaning fluids recommended by your paint supplier.
© Fast & Fluid Management, AT550 C - Monthly maintenance > Remove back panel. Check pump for possible malfunctions (e.g. leakage or blockage). Attention! MOVING PARTS CAN CAUSE INJURY. Always turn off power before accessing moving parts.
© Fast & Fluid Management, AT550 Troubleshooting A - Introduction Before calling your machine supplier or Service Department, please c heck whether you c an solve the problem yourself. If you cannot, then c all the Service Department for advice. Have the m odel number and serial number at hand (these can be found on the silver CE sticker at the service panel at the back of the m achine). Use the Problem Solving chart below to judge whether you c an solve a problem yourself or not.
© Fast & Fluid Management, AT550 Technical specifications p17
© Fast & Fluid Management, AT550 Contributing to the Protection of the Environment Packaging Material The packaging protects the machine against damage during transport. The pac kaging material was c hosen based on its limited impact on the environment and its inherent possibilities for waste- disposal. The reuse of packaging material saves raw materials and produces less waste material. Generally speaking, your supplier will take the packaging off your hands.
© Fast & Fluid Management, 2007 w w w .Fast-Fluid.
