FAST & FLUID MANAGEMENT SK450 ENGLISH
Fast & Fluid Management - SK450 p2
Fast & Fluid Management - SK450 Table of Contents SK450 Manual (EN) EU Declaration of Conformity Introduction & warranty Main SK450 components Safety instructions Installation Operation Maintenance Problem solving Error codes Fuses Specifications Electrical wiring diagram Contributing to the Protection of the Environment p3 5 5 6 7 8 9 12 16 17 19 20 21 22 23
Fast & Fluid Management - SK450 p4
Fast & Fluid Management - SK450 SK450 Manual (EN) EU Declaration of Conformity We, Fast & Fluid Management, the Netherlands A Unit of IDEX Corporation Hub van Doorneweg 31 2171 KZ Sassenheim, the Netherlands Declare that: product: Automatic Shaker model: Skandex type: SK450 are in compliance with the following directives: Machinery Directive 2006/42/EC Low Voltage Directive 2006/95/EEC Electromagnetic Compatibility Directive 2004/108/EEC according to the following harmonized standards: EN-ISO 12100-1
Fast & Fluid Management - SK450 Introduction & warranty Introduction By selecting a Fast & Fluid Management shaker you have opted for a product which is the result of intensive research. Top-quality components, craftsmanship and a modern ergonomic design all serve to guarantee a long service life and a high degree of user friendliness.
Fast & Fluid Management - SK450 Main SK450 components 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
Fast & Fluid Management - SK450 Safety instructions General safety instructions Attention! Before installing the equipment and setting it in operation, please read the instructions carefully. This is safer both for youself and prevents unnecessary damage to the machine. The manufacturer accepts no liability if the instructions below are not followed: 1. If a machine has been damaged (during transport, for example), do not attempt to set it in operation.
Fast & Fluid Management - SK450 Installation Step 1 - Unpack the machine and unlock the frame lock > Remove box and plastic foil. Note the frame lock bolts on either side of the machine. > Remove both bolts with a size 17 fork wrench. By removing the bolts, the frame lock’s wooden block is released. Be careful not to damage the body and surfaces of your SK450 with any tools while unpacking it.
Fast & Fluid Management - SK450 Attention! Failure to remove the frame lock correctly can result in severe damage to your SK450 when in operation. Please take care! Please take care to store the frame lock for later use, it is essential for correct transportation. Step 3 - Detach shaker from its transport skid > Pull out cord to remove frame lock’s loose parts. Ensure all loose parts have been removed – two bolts and two wooden blocks.
Fast & Fluid Management - SK450 Step 4 - Place the machine in its final operational position > Lower the adjustable feet far enough to lift the machine off its wheels. > Take care to correctly level the machine (by turning the adjustable feet). Lock all adjustable feet by tightening the their separate bolts. Tip: before locking the adjustable feet, start a mixing cycle with a small load (<5kg). While the SK450 runs, check if all four feet are firmly in contact with the floor and then lock them.
Fast & Fluid Management - SK450 Operation A - First time operation Attention! Before operating your SK450 for the first time, please ensure the frame lock was correctly removed (Click here to see) Step 1 - SK450 power management Turn the emergency stop clockwise to unlock: the screen displays the startup actions and 'ready' message. Unlock the emergency stop button on the front of the machine by turning clockwise.
Fast & Fluid Management - SK450 Step 2 - Correct placement of cans and other containers > Place one or more containers at gravitational center of the can table, between the spindles. > Place filler disc on lid to prevent displacement during operation. Use the hook to fixate the can handle. When mixing more than one can, use adhesive tape.
Fast & Fluid Management - SK450 B - Operating the SK450 Step 1 - Place can, choose program and start program > Place the container in the can table center, place filler disc and attach hook to container handle. > Close door. If your SK450 is fitted with an electric door, skip this step as it will close automatically later. Choose correct program and press desired timing button. Clamping and mixing will now start. Attention! The mixing program will not start unless the door is closed.
Fast & Fluid Management - SK450 C - User presets for the SK450 Certain SK450 software presets can be adjusted using the interface screen and buttons. To enter the User Mode menu, press the emergency stop button and then unlock it while simultaneously keeping the program button (P) pressed. Upon entering the User Mode menu, a screen will appear showing your SK450 ’s life in mixing cycles and total hours. Press the program button to run through the different user menu’s.
Fast & Fluid Management - SK450 Maintenance Keep your SK450 clean and free of paint residue > Remove all spilt paint from accessible parts (especially clamping plate spindles). Use diluted detergent only and Teflon spray only. Though the SK450 is designed to be completely maintenance free, periodic greasing of moving parts will ensure it remains in top shape. Attention! MOVING PARTS CAN CAUSE INJURY. Always turn off power (e.g. by pressing emergency stop) before accessing moving parts.
Fast & Fluid Management - SK450 Problem solving Introduction Before calling your machine supplier or Service Department, please check whether you can solve the problem yourself. If you cannot, then call the Service Department for advice. Have the model number and serial number at hand (these can be found on the silver CE sticker at the back of the machine). Use the Problem Solving chart below to judge whether you can solve a problem yourself or whether you need to call in the Service Department.
Fast & Fluid Management - SK450 Too much mechanical resistance Clean the spindle and lubricate Clamping plate will not go up after mixing Clamping plate is jammed Use interface user setting U4 If persistent, call service Container unclamps while mixing Container(s) not centered Replace container(s) in gravitational centre.
Fast & Fluid Management - SK450 Error codes Error Cause Action E01 Clamping motor power too low or bad electric wiring Call service E02 Preset minimal clamping pressure not reached Call service E03 Door opened during mixing or door switch defective Keep door closed during mixing.
Fast & Fluid Management - SK450 Fuses Replace fuse at rear of SK450. > Remove mains connector and pull fuse tray outwards. The inner fuse is the (damaged) one to replace, the outer is the spare to replace it with. p20 Dispose of the burnt fuse and in time, remember to get a new spare, type 5x20/T10A (slow). If problem persists, check mains for power surges.
Fast & Fluid Management - SK450 Specifications Maximum product weight 40 kg Timer electronic/programmable Maximum product size (H x W x D) 45 x 35 x 35 cm Minimum product height 7 cm Clamping automatic Clamping pressure variable Product access internal sliding door Shaking speed variable up to 720 rpm Sliding table option Large can table standard Machine size (H x W x D) 116 x 72 x 61 cm Machine weight (empty) 180 kg Available colors available side panels available in all (RAL) col
Fast & Fluid Management - SK450 Electrical wiring diagram SicherheitsanweisungenBetrieb p22
Fast & Fluid Management - SK450 Contributing to the Protection of the Environment Packaging Material The packaging protects the machine against damage during transport. The packaging material was chosen based on its limited impact on the environment and its inherent possibilities for waste-disposal. The reuse of packaging material saves raw materials and produces less waste material. Generally speaking, your supplier will take the packaging off your hands.
© Fast & Fluid, 2007 w w w .Fast-Fluid.
