© Fast & Fluid Management, TMHC manual FAST & FLUID MANAGEMENT TMHC ENGLISH p1
© Fast & Fluid Management, TMHC manual Table of Contents TMHC Manual (PC model) EU Declaration of conformity Introduction & warranty Explanation of drawing Safety instructions Installation Use Maintenance Service Technical specifications Wiring diagram Contributing to the Protection of the Environment p2 3 3 4 6 7 8 9 11 13 15 16 17
© Fast & Fluid Management, TMHC manual TMHC Manual (PC model) EU Declaration of conformity We, Fast & Fluid Management, the Netherlands A Unit of IDEX Corporation Hub van Doorneweg 31 2171 KZ Sassenheim, the Netherlands declare that: Product: Personal care dispensers Model: Tintmaster Types: Hair Care are in compliance with the following direc tives: Machinery Directive 98/37/EC Low Voltage Directive 73/23/EEC Electromagnetic Compatibility Directive 89/336/EEC according to the following harmonized st
© Fast & Fluid Management, TMHC manual Introduction & warranty Introduction By selecting a Fast & Fluid Management Dispenser you have opted for a product which is the result of intensive research. Top-quality components, craftsmanship and a modern ergonomic design all serve to guarantee a long service life and a high degree of user friendliness.
© Fast & Fluid Management, TMHC manual In the event that the PU experiences a breakdown, the other party m ay use the software on another processing unit until the PU is again operational. The other party will inform F&FM of this within 5 days. If it is a requirement that the Software be definitively transferred from the PU to another proc essing unit then the other party shall request perm ission from F&FM, which will not withhold suc h permission on unreasonable grounds.
© Fast & Fluid Management, TMHC manual Explanation of drawing 1. 2. 3. 4. 5. 6. 7. Top panel Pump & Canister Flatscreen Powerboard Gripper assy On/Off switch Side panel 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
© Fast & Fluid Management, TMHC manual Safety instructions General safety instructions Attention! Before installing the equipment and setting it in operation, please read this manual carefully. This is safer both for yourself and the machine. The manufacturer accepts no liability if the instructions below are not followed: 1. 2. 3. 4. 5. 6. 7. If the TMHC has been damaged (e.g. during transport), do not attempt to set it in operation.
© Fast & Fluid Management, TMHC manual Installation A -Installing the dispenser Step 1 - Unpack the machine > Place the skid near the place of installation. Remove the c ardboard box. > Remove the plastic foil around the machine. Remove skid brackets. There are 4 of them (1 on each corner). > Remove the brackets between the dispenser and the cabinet. There are 4 of them ( 1 one each corner). Remove the foam that is located in the dispense bay and on top of the turntable.
© Fast & Fluid Management, TMHC manual Use A - First time operation Step 1 - Switching ON the dispenser & computer > The dispenser can be turned on by the switch located on the side of the door (the computer starts up automaticly when you turn on the dispenser). Now turn on the touchscreen. Step 2 - Switching OFF the dispenser & computer > Please note that with normal operation there should be no reason to take the power off the dispenser.
© Fast & Fluid Management, TMHC manual Replacing pouch Follow instructions on screen.
© Fast & Fluid Management, TMHC manual Maintenance Weekly maintenance Cleaning the brush tray. > Open the TMHC door and remove the steel drip tray. Clean with water if soiled. > Pull out the brush tray and rinse with water. Clean the brush with water and dry it. For further information on what should be used in the brush container as cleaning fluid, ask your supplier. If severely soiled, the brush can be removed from the tray for cleaning. Use only cleaning fluids recommended by your supplier.
© Fast & Fluid Management, TMHC manual Cleaning the leak tray. Pull out the leak trayand clean it with water if soiled. Be carefull when removing the leak tray, there can be fluids in there.
© Fast & Fluid Management, TMHC manual Service A - Introduction Before calling your machine supplier or Service Department, please chec k whether you can solve the problem yourself. If you cannot, then call the Servic e Department for advic e. Have the model number and serial number at hand (these can be found on the silver CE sticker at back of the m achine, next to the net entry or behind the front door of the machine).
© Fast & Fluid Management, TMHC manual D - Fuse Replacing fuse in net entry.
© Fast & Fluid Management, TMHC manual Technical specifications Number of pouch positions 32 Pouch sizes 1 liter Valves 32x Stainless steel (mold) Variations only upon specific request Pump type piston pump Pump sizes 1 ounce Min. dispensing 1/384 fl.oz * Accuracy 0.004 ml/step * Nozzle closures integrated Cleaning system standard Nozzle diameter 2 and 4,5 mm Maximum load height 12 cm Can detector standard Dimensions (H x W x D) Dispenser 86 x 74.2 x 82.
A B C 5 COM 2 PORT #1 PORT #2 - S + J19 HHB1 HHB2 HHB3 HHB4 HHB5 MGND1 MGND2 HHB6 HHB7 MGND2 MGND2 HHB8 HHB9 HHB10 HHB11 HHB12 MGND3 HHB13 HHB14 MGND3 - S + 1 2 4 5 6 8 3 3 POW ERBOARD 2001 POWERSUPPLY COMMUNICATION LK1 BLUE BROWN 0 42= YELLOW RED or or YELLOW & WHITE/RED RED & WHITE/YELLOW 4 PC ORANGE or BLACK & WHITE/ORANGE COM 1/USB SLP BLUE or ORANGE & WHITE/BLACK BROWN BLUE BROWN BLUE BLUE BROWN BLUE BROWN BLUE BROWN BLUE BROWN + +
© Fast & Fluid Management, TMHC manual Contributing to the Protection of the Environment Packaging Material The packaging protects the machine against damage during transport. The packaging m aterial was chosen based on its limited impact on the environment and its inherent possibilities for waste disposal. The re use of packaging material saves raw materials and produces less waste material. Generally speaking, your supplier will take the packaging of your hands.
© Fast & Fluid Management, TMHC manual © Fast & Fluid Management, 2007 w w w .Fast-Fluid.
