Original Manual X-Smart® www.fluidman.com V 1.2 www.fast-fluid.
© Fast & Fluid Management B.V. This manual or parts thereof may not be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, nor otherwise, without the prior written permission of Fast & Fluid Management B.V. This manual could contain technical inaccuracies or typographical errors. Fast & Fluid Management B.V.
Table of Contents Table of Contents 1 2 3 4 5 About this manual......................................................................................................... 5 1.1 How to work with the manual ............................................................................................5 1.2 Record of changes............................................................................................................5 Safety ...................................................................
Table of Contents 6 Technical data ............................................................................................................. 23 6.1 General specifications ....................................................................................................23 6.2 Dimensions and mass ....................................................................................................23 6.3 Ambient conditions .............................................................................
About this manual 1 X-Smart About this manual The manual shows the information necessary to: - install the machine - operate the machine - perform basic maintenance - correct small problems. The X-Smart and all its versions are referred to in the manual as the ’machine’. This manual contains the original instructions. The original language of the manual is English. Note For the unpacking and installation procedures, refer to the separate installation instruction sheets. 1.
About this manual X-Smart 6 V 1.
Safety 2 X-Smart V 1.2 Safety WARNING Read the manual before you install or use the machine. Failure to do so can result in personal injury, death or property damage. 2.1 Intended use The machine is designed to dispense colorants into a can. Any other use of the machine is strictly forbidden. 2.2 Liability Our machines and accessories are fully compliant with the CE regulations. Any modification can result in not fulfilling the CE safety requirements and is therefore not allowed.
Safety 2.4 X-Smart V 1.2 Certifications For some markets machines need a certification to proove the machine complies with the essential requirements concerning safety. The directives that have been taken into consideration in the design are available on the website. If applicable to your market, the machine contains the logo of the certification either as a seperate sticker or on the type plate. /i Logo 2.5 Certification Website CE www.fast-fluid.
Safety 2.6 X-Smart V 1.2 Safety symbols in the manual /i WARNING Can cause personal injury. Note Shows further information. CAUTION Can cause damage to the machine. 2.7 Disposal of the machine 1. Sort the machine, the accessories and the packaging for environmentally friendly recycling. 2. Do not dispose of the machine into domestic waste. Dispose of the machine according to local regulations. 3. Dispose of the canisters as chemical waste, according to the local regulations.
Safety X-Smart 10 V 1.
Operator manual 3 Operator manual 3.1 Description 3.1.1 Overview of the machine X-Smart V 1.
Operator manual 3.1.2 X-Smart V 1.
Operator manual 3.1.3 X-Smart Type plate: details XXXX www.xxxxxx.com 24VDC 75W Model Serial no. Prod.week Mass Made in X-Smart xxxxx-xx-xxxxxxxx xx-xxxx xx kg xxxxx Patented families Design © 3.2 Operation WARNING Do not place objects on top of the machine. CAUTION Do not remove the power from the machine. See § 4.1. The machine must stir the colorants periodically. 3.2.1 General dispensing procedure For all the dispense software instructions: see the dispense software documentation. 1.
Operator manual 3.2.2 X-Smart V 1.2 Placing a can 1. Check the height of the can. E Note The correct height of the can table depends on the height of the can. B C D 2. Place the can table (A) in the correct slots for the correct height. A CAUTION Make sure that the can table is secure. 3. Place the can (B) at the center of the mark (C) on the can table. CAUTION Make sure that the can does not touch the turntable (E). Keep enough free space.
Operator manual X-Smart 3.3 Maintenance 3.3.1 X-Smart Maintenance Kit V 1.2 To keep your X-Smart in optimal condition, we highly recommend you to use the X-Smart Maintenance Kit. The X-Smart Maintenance Kit contains everything you need to keep your machine in optimal condition for the period of 1 year.
Operator manual X-Smart V 1.2 2. When the brush is too dirty and does not clean the nozzle of the canister, rinse and clean the brush. See § 3.3.3. 3. When the nozzles are too dirty, clean the nozzles individually with a damp cloth. See § 3.3.4. 3.3.3 Cleaning the brush unit: daily The brush unit removes the excess colorant from the nozzles. The brush unit consists of a brush container and a removable brush that rotates. The brush unit is installed in a bracket with a click connection.
Operator manual X-Smart V 1.2 7. Fill the brush container with fluid. This fluid must be a waterbased cleaning agent. F WARNING Do not put flammable liquids in the brush container. Note Do not exceed the maximum filling height (F). Note The optimum fluid level depends on the type of colorant that is used. 8. Slide the brush unit (A) back in the bracket (B). Note The brush unit is properly connected to the bracket when you feel a snap-fit. Make sure you hear the click sound. A B 3.3.
Operator manual 3.3.5 X-Smart V 1.2 Refilling a canister WARNING Check the material safety data sheet (MSDS) of the colorants for the personal protection measures that are required for handling the colorant. CAUTION Make sure that the colorant level in the canister is correct. If a canister is empty, it can cause an inaccurate dispensing and/or a recipe fault. Note The dispense software checks the level of colorant in each canister. The dispense software shows when you need to refill a canister. 1.
Installation 4 X-Smart Installation Note For the unpacking and installation procedures, refer to the separate installation instruction sheets. 4.1 Turning on the machine 1. Connect the power cable to the wall socket. When the machine is operational, you hear two ’beeps’. 2. Make sure that the emergency stop switch is released. 3. Set the computer switch to ‘ON’. 4. Run the dispense software. 4.2 First use 1. Fill and place the brush unit. See § 3.3.3. 2. Fill the canisters correctly. See § 3.3.5. 3.
Installation X-Smart 20 V 1.
Troubleshooting 5 X-Smart V 1.2 Troubleshooting Note For all error messages on the computer: see the help topic in the dispense software. 5.1 Contact service 1. Find the type plate on the plate next to the emergency stop switch. See § 3.1.3. 2. Take a note of the model number and the serial number of the machine. 3. Contact your supplier or manufacturer. See www.fast-fluid.com (Fast & Fluid Management Europe and Asia) or www.fluidman.com (Fluid management, U.S.A.). 5.
Troubleshooting X-Smart 22 V 1.
Technical data 6 Technical data 6.1 General specifications X-Smart V 1.2 /i Parameter Specification Metric standard Model X-Smart Number of canisters 16 Dispensing Sequential Pump type Piston pump Cleaning system Rotary brush Suitable for Water and universal colorants Canister size Resolution Maximum flow rate Minimum dispensing Nozzle diameter 6.2 Imperial standard 2.25 L 0.594 USgal ± 0.005 mL/step ± 0.000169 fl oz/step 0.25 L/min. 0.066 USgal/min. 0.077 mL 0.
Technical data 6.3 X-Smart V 1.2 Ambient conditions /i Parameter Specification Metric standard Imperial standard Temperature +15 to +40 °C +59 to +104 °F Altitude above sea level, operational -10 to 2000 m -33 to 6562 ft Altitude above sea level, out of operation -10 to 12000 m -33 to 39370 ft Maximum Relative Humidity, without condensation 6.4 90% RH Noise level /i Parameter Specification Maximum noise level 6.
A B C D 3 5 TURNTABLE MOTOR M6 AGITATION MOTOR M5 4 1 M1 4P-STEPPERMOTOR 2 Cable, Turntable Cable, Turntable Cable, Agiation Cable, Agiation 4 USB to PC 4 BLUE BROWN BLUE BROWN Cansensor Cansensor 3 (OPTION) CANSENSOR S3 S1 MACHINE STOP 3 RED YELLOW ORANGE BLUE BLUE BLACK BROWN 2 Revnr. 1.0 2.0 2.01 2.02 Date 21-1-2013 3-4-2013 17-4-2014 XSmart Filename Title 2.
Manufactured by: IDEX Fluid & Metering Pvt. Ltd., Survey no: 256, GIDC Manjusar, Savli, Dist.
