FAQ

NO
M
O
R
E
T
A
P
E
Paint more.
Mask less.
What is FastMasQ?
FastMasQ is an acrylic modified water based clear coating formulated to peel from
glass, FastMasQ may be used Interior or Exterior.
What type glass can FastMasQ be used on?
FastMasQ can be used on standard tempered glass. Do not use on stained, frosted,
coated, etched, tinted or textured glass, plastic glass or Plexiglas.
Can FastMasQ be used as a primer on surfaces around glass to be masked?
FastMasQ is a good primer for bare wood, de-glossed painted surfaces, dull primed
metal and finished aluminum. FastMasQ will adhere to vinyl surfaces so be sure that is
is used as a primer only.
What finish coats are acceptable over FastMasQ?
All latex, acrylic, vinyl acrylic and alkyd coatings are acceptable finish coats.
Dry Times: The drying time of FastMasQ is important!
• Water based finish coats: Allow FastMasQ to dry for 3 to 4 hours before topcoating.
•
Alkyd & Water Reducible Coatings: Allow FastMasQ to dry overnight before top
coating.
DO NOT use lacquers or any coating containing strong solvents such as alcohols or
ket
ones over FastMasQ.
Can I stain over FastMasQ?
No, FastMasQ will seal the wood and not allow penetration of the stain.
What type surfaces can FastMasQ be used on?
FastMasQ is formulated to peel readily from glass surfaces. (It will also peel from glossy,
non porous surfaces.) FastMasQ will adhere to bare wood, de-glossed painted surfaces,
dull porous aluminum and primed metal (dull sheen). FastMasQ will bond to vinyl so use
as a primer.
What condition should the surface be in before applying FastMasQ?
Surfaces must be clean, dry and free of any foreign material. Glossy surfaces must be
dulled by sanding. Surface temperatures should be above 50°F. In extremely cold areas,
the glass temperature may be much colder than the room temperature.
How can I apply FastMasQ?
FastMasQ can be applied by brush (quality nylon), roller (quality lambskin with a 1" nap),
or spray (airless or HVLP). It is best to apply a full coat that will dry down to 3 mils dry.
Spray: For best results when spraying, thin FastMasQ with 1 pint of clean water per
gallon and mix thoroughly. Using a 417 tip, spray a test area adjusting pressure and
volume until proper atomization is achieved.
How long does FastMasQ take to dry?
FastMasQ will dry in 30 - 45 minutes. However, allow 3 to 4 hours dry time before
applying water based finish coats and overnight dry before applying alkyd based finish
coats. Temperature and humidity will effect dry time of the FastMasQ.
How long may FastMasQ remain on glass before it is difficult to remove?
FastMasQ should be removed within 30 days. In areas with prolonged sunlight and low
(dry) humidity, FastMasQ should be removed sooner. Changes in temperature, i.e. 20° -
40° drop in overnight temperature, will influence the peelibility of the FastMasQ.
What is the best method of removing FastMasQ?
The best way is to start in a corner using a dull knife (glass scores easily so be careful)
and work around the glass edges. Carefully peel away the masking liquid. If FastMasQ is
difficult to remove, wet the surface with warm water on a sponge or cloth. In colder
temperatures it may be necessary to use a hot air blower to removed FastMasQ from
cold windows.
Frequently Asked Questions
1
Prepare
the surface
2
Spray,
Brush or
Roll-on
5
Peel off
the film
4
Cut outline
around the
window
3
Paint
Instructions
USAGE: A superior high solids-low voc latex coating formulated to save the
professional time and dollars when masking off sash and trim. FastMasQ is
designed to mask glass. FastMasQ is formulated to adhere to interior and
exterior wood and properly prepared previously painted surfaces. Use on
exterior and interior bare wood, aluminum, and painted surfaces. Will not peel
off most vinyl frames. Will cause bare metals to flash rust. Use Solventborne
Masking Liquid on bare metal. Not intended for use on stained, frosted, coated,
or textured glass or Plexiglas and some types of specialty glass. Do not use on
bare wood where a stain finish is to be used. Do not use under lacquer or
products containing strong solvents ie: ketones or alcohols. Do not top coat
FastMasQ with fast and hard drying water-borne coatings.
SURFACE PREPARATION: All surfaces must be clean, dry and free of any oils,
wax and other foreign material. Glass must be clean, dry and free of stickers.
Check glass for scratches or defects. Bring any irregularities to the attention of
the owner or general contractor. Clean bare wood, sand smooth and wipe off
dust. If painted surface is glossy, dull by sanding and remove dust. If painted
surface is chalky, scrub with a brush and water to remove.
APPLICATION: Since the manufacturer has no control over the surface, surface
preparation, or methods of application, it is up to the user to try a test area
following label directions to assure compatibility with the surface, peel ability
and compatibility of the finish coat.
Mix FastMasQ well before using. Do not thin (for spray, a small amount of clean
water may be added for good atomization). Protect all areas not to be treated.
Apply a coat (2-4 mm dry) to glass and sash areas. If using as a primer over
sash, mullions, etc., be sure the FastMasQ is absorbed into the wood. Apply by
brush, roller, or spray (2500psi and .017 tip).
COVERAGE: FastMasQ will cover up to 250 sq. ft. per gallon at 2-4 mm dry.
DRYING TIME: FastMasQ will dry to the touch in 30 minutes. Allow 3-4 hours
before applying latex finish coats and overnight dry for alkyd or waterborne
finish coats.
REMOVAL: Using a dull knife, start at a comer about 1/16 in. from the sash.
Cut carefully into the film just enough to be able to peel the coating off. To
insure peel ability, remove within 30 days.
CONTAINS: acrylic polymers, polyurethane resin.
VOC CONTENT LIMIT: < 50 g/l
IMPORTANT: For best results when spraying FastMasQ, strain the Masking
Liquid into a clean pot. Dilute with 16 fluid ounces of clean water per gallon of
Masking Liquid and mix thoroughly. Use a 417 tip at low pressure and spray a
test area, adjusting pressure and volume to achieve proper atomization, giving
a smooth film void of spatters and orange peel. Stop spraying until proper
atomization is achieved. MIX Masking Liquid occasionally during use. When
done, clean the pot thoroughly with warm soapy water.
Be Legend Inc. Miami, FL
Prepared for:
7
rolls
of tape
is equivalent to
1Qt