Instructions / Assembly

Be Legend, Inc.
July 06 www.belegend.ca
Characteristics:
80-400 FastMasQ Liquid Masking
is a high solids low voc coating
specifically designed for masking
doors and window glass. It adheres
to wood and removes easily from
the glass. Masking Liquid H2O is
also an excellent sealer for bare
wood and other porous surfaces.
Vehicle Type: Proprietary Blend
FINISH: Medium Luster
RECOMMENDED USES:
TINTING:
None
THINNING:
Not recommended, see spray
instructions.
DRYING TIME, @ 77º F, 50% RH:
Temperature & Humidity Dependent
Touch: 1 Hour
Topcoat:
• Acrylic, Vinyl Acrylic & Latex: 4 Hours
• Alkyd and water reducible coatings: 12-
Hours (call for clarification)
Flash Point: N/A
VOC: <100 g/l
Weight Solids: 52.0% ± 2%
Volume Solids: 46.0% ± 2%
Weight Per Gallon: 8.9 Lbs
COVERAGE:
80-400 will cover up to 400 sq.ft per
gallon @ 6.0 mils wet, 3.0 mils dry or
3000 linear feet of 1” stripe.
Surface Preparation
All surfaces mu
st be clean, dry and free of
any foreign material. Check glass for any
defects and report to homeowner or con-
tractor. All bare wood, primed metal,
aluminum must be clean, porous and free
of any defects. Dull glossy surfaces by
sanding. Do not
use on bare wood if it is
to be stained. Do not use on stained,
frosted, etched, tinted, or textured and
plastic glass or PLEXIGLASS. It is ad-
visable to try a test area first to check for
adhesion, peelibility (over glass) and
compatibility of the finish coat. Apply
when ambient temperature is between 50°
F and 90°F. Remember in cold areas and
hot humid areas window temperatures will
be different from air temperatures. Mask-
ing Liquid H2O will adhere to vinyl so
use only as a primer.
Application:
Apply when ai
r and surface te
mperature is
between 50°F and 90°F. Apply with a
quality nylon brush, 1” nap lambskin
roller or, spray (airless or HVLP). When
brushing apply a 1” band on the glass and
on the frame if priming. When rolling a
4” roller would be practical for coating
glass and frames.
Spray:
For best results, strain Masking Liquid
H2O in to a clean pot. Dilute with 1 pint
of water per gallon of Masking Liquid
H2O and mix thoroughly. Use a .017(417)
tip at low pressure and spray a test area.
Adjust pressure and volume to achieve
proper atomization, giving a smooth film
free of spatters and orange peel. Do not
continue spraying until proper atomization
is achieved. Mix Masking Liquid H2O
occasionally while in use.
See Associated's Masking Liq-
uid H2O Frequently Asked
Question Sheet and call if there
are additional questions.
Surface Preparation
Warning
! Removal of old paint by
s
anding, scraping or other means may
generate dust or fumes that contain
lead. Exposure to lead dust or fumes
may cause brain damage or other
adverse affects, especially in children
or pregnant women. Controlling expo-
sure to lead or other hazardous sub-
stances requires the use of proper
protective equipment, such as a prop-
erly fitted respirator (NIOSH approved)
and proper containment and cleanup.
For more information, call the National
Lead Information Center at 1-800-424-
LEAD (in US) or contact your local
health authority.
Warning! Do Not
apply lacquers or
any finish coating that contain strong
solvents such as ketones or alcohol.
Cleanup Information
Clean spills and spatters immediately
with soap and warm water. Clean
hands and tools immediately after use
with soap and warm water. After
cleaning, flush spray equipment with
mineral spirits to prevent rusting of the
equipment. Follow manufacturer’s
safety recommendations when using
mineral sprits.
Removal
Glass scores easily so be careful
when removing Masking Liquid H2O.
Using a dull blade, start in one corner
and work around cutting close to the
sash. Peel FastMasQ Masking Liquid
away carefully. If FastMasQ
Masking Liquid is difficult to
remove, wet the surface with warm
water on a sponge or wet cloth. In
colder temperatures, it may be nec-
essary to use a hot air blower to soften
the FastMasQ Masking Liquid. Do
not allow FastMasQ Masking Liquid
to remain on glass for more than
30 days, particu-larly in hot, dry
climates.
• Interior Wood
• Vinyl
• Aluminum
• Properly pre-
pared painted
surfaces
80-400.01
FastMasQ Masking Liquid
Data Sheet