Datasheet

Technical Data & Packing Spec
www.fastrongroup.com
•• All dimensions in mm
Revision date : 14 Aug 2014
Suppression CoilsSuppression Coils
FASTRON suppression coils come with high rated currents and low DC resistance characteristics. Inductance values range from 1µH to 10 000µH. They are available in
tape and ammopack packing.
Applications
Communication: RF blocking, filtering and decoupling
Others: entertainment electronics and interference suppression
Packing
Specification
Standard Axial Taping
91
9
10
Ordering Code Example:
MISC-100X-YY
Core Types - Ferrite, Iron Dust
Tolerances - K (10%), M (20%)
Packing Code - 00 (Loose in Box), 01, 04 (Taped / Reel)
MISC - 100 X - YY
(Model) (Inductance Value) (Tolerance) (Packing Code)
MISC-100M-01
Technical Data
H
T
Fig.1
B
b
d1
d
D
P0
P
P1
W
drawing only schematic, see table
Type D D0 d d1 B b W P P0 P1 H T
MESC [-04] 330 1.5 100 13 47.5 43.9 44 16 4 2 7.5 0.5
SMD Taping
L – Value (rated inductance)
Measured with Bode 100 Vector Network Analyzer at frequency f
L
DCR (max)
Measured at 25°C
Rated DC Current
I based on temperature rise, determined at the point where the temperature rise does not exceed
40°C above the ambient temperature of 25°C
Operating Temperature
-55°C to +125°C (includes component self-heating)
Recommended soldering method
Wave (Leaded)
Reflow (MESC SMD version)
Moisture Sensitivity Levels (MSL)
MSL Level 1, indicating unlimited floor life at ≤ 30°C / 85% relative humidity
Solderability
Using lead free solder (Sn 99.9) at 260°C ± 5°C for 5 ± 0.5 seconds, min 90% solder coverage of
metallization
Standard: IEC 68-2-20 (Ta)
Resistance to Soldering Heat
Resistant to 260°C ± 5°C for 10 ± 1 seconds
Standard: IEC 68-2-20 (Tb)
Resistance to Solvent
Resistant to Isopropyl alcohol for 5 ± 0.5 minutes at 23°C ± 5°C
Standard: IEC 68-2-45
Climatic Test
Defined by the following standards
IEC 68-2-1 for Cold test: -55°C for 96 hours
IEC 68-2-2 for Dry heat test: +125°C for 96 hours
IEC 60068-2-78 for Humidity test: 40°C at RH 95% for 4 days
Thermal Shock Test
Temperature cycle : -55°C to +125°C to -55°C
Max/Min temperature duration: 15 minutes
Temperature transition duration: 5 minutes
Cycles: 25
Standard: MIL-STD-202G
Tensile Strength of Leads
(Pull Test)
Components withstand a pulling force of 20N for 10 ± 1 seconds
IEC 60068-2-21 (Ua
1
)
Mechanical Shock
Mil-Std 202 Method 213
Condition C
3 axis, 6 times, total 18 shocks
100 G, 6 ms, half-sine
Vibration
Mil-Std 202 Method 204
20 mins at 5G
10 Hz to 2000 Hz
12 cycles each of 3 orientations
D0
Packing code : 04 Packing code : 01