ELECTRONIC KEYPAD LEVER LOCK User's Guide
IMPORTANT SAFETY INSTRUCTION WARNING 1. To prevent damage to the finish, DO NOT use any abrasives, sharp objects or harsh chemical products containing alcohol, petroleum solvents, acids or acetone to clean this lockset. 2. To prevent damage to the sensitive electronic components, DO NOT allow any liquids to enter lockset while installing or cleaning. CAUTION ! 1. Do not attempt to disassemble any internal components of this lockset as this WILL void the limited warranty. 2.
CONTENTS INSTALLATION INSTRUCTIONS 1. COMPONENTS TEMPLATE 2. DOOR PREPARATION 3. LATCH INSTALLATION 4. STRIKE PLATE INSTALLATION 5. LEVER DIRECTION DETERMINATION 6-1. TO RESET DIRECTION OF INSIDE LEVER 6-2. TO RESET DIRECTION OF OUTSIDE LEVER 7-1. MOUNTING EXTERIOR ASSEMBLY 7-2. PREPARING TO MOUNT INTERIOR ASSEMBLY 7-3. REMOVING DECORATIVE COVER 7-4. MOUNTING INTERIOR ASSEMBLY 7-5. BATTERY INSTALLATION 7-6. REINSTALL LEVER 8-1. EXCHANGE OF LEVER 8-2. EXCHANGE OF LEVER (REMOVAL OF INSIDE LEVER) 8-3.
CONTENTS MAIN OPERATING INSTRUCTIONS SETUP MODE 1. CHANGE PROGRAMMING CODE 2. ADD A USER CODE 3. DELETE INDIVIDUAL EXISTING USER CODE 4. DELETE ALL THE EXISTING USER CODES AT ONCE 5. DISABLE ALL THE EXISTING USER CODES (VACATION MODE) 6. DISABLE BUTTON SOUND (MUTE MODE) 7. SETTING AUTO-LOCK TIME DELAY 8. RESTORE FACTORY SETTING OPERATION MODE 1.TO ACTIVATE AUTO-LOCKING (AUTOMATIC RE-LOCKING) 2. TO OPEN (UNLOCK) THE DOOR 3.
INSTALLATION INSTRUCTIONS 1. COMPONENTS A. Key B. Exterior Assembly C. Mounting Plate D. Interior Assembly E. Decorative Cover F. Battery Pack Cover G. Lever H. 5/16''(7.8mm) Screw (2) E I. 1-1 /4'' (32mm) Screw (2) J. Latch K. 6/8''(19.2mm) Wood Screw (4) L. Strike M.
TEMPLATE IMPORTANT BEFORE PROCEEDING 1. Remove lever lock, or do not install lever lock prior to painting your door. 2. Do not let any water or liquid into the lockset during installation process. NOTE:MEASUREMENTS BELOW ARE JUST A GUIDELINE. Please measure your door to determine the exact center of your door edge.
DOOR PREPARATION 2. DOOR PREPARATION NOTE: If replacing an existing lock or installing in a pre-drilled door, begin with page 7. Fold the template against the door edge as shown in below illustration, mark and drill a pilot hole for latch on door edge, select backset (60mm or 70mm) to mark and drill a pilot hole for selected backset on door face. (It is recommended to mark centerline of the hole on door about 36 inches (914mm) above the floor.
INSTALLATION INSTRUCTIONS 3. LATCH INSTALLATION 60mm(2-3/8'') Drive-shaft B. Push the drive-shaft forward for adjustment to 60mm(2-3/8''). 70mm(2-3/4'') Drive-shaft A. Pull the drive-shaft backward for adjustment to 70mm(2-3/4'').
INSTALLATION INSTRUCTIONS 3. LATCH INSTALLATION A. Insert the latch into the latch hole. Using the faceplate as a pattern, TRACE a line along the out edge of the faceplate and chisel a 4mm (1/8") slot in the marked out area. Face plate should fit flush with door edge. B. Insert the latch into the latch hole and fasten with screws.
INSTALLATION INSTRUCTIONS 4. STRIKE PLATE INSTALLATION A. Placing the strike plate on the door frame, TRACE a line along the out edge of the strike plate and chisel a 3mm (1/8") slot in the marked out area. B. Chisel out a hole measuring 32 x 24 x 13mm (1-1/4''X1''X1/2'') in association with the size of the dust box. C. Fasten the strike and dust box with screws.
INSTALLATION INSTRUCTIONS 5. LEVER DIRECTION DETERMINATION NOTE: Do not install the lock when the lever is at vertical position. Before lock installation, please determine the inside lever direction according to the opening direction of door as shown.
INSTALLATION INSTRUCTIONS 5. LEVER DIRECTION DETERMINATION NOTE: Do not install the lock when the lever is at vertical position. Before lock installation, please determine the outside lever direction according to the opening direction of door as shown.
INSTALLATION INSTRUCTIONS 6-1. TO RESET DIRECTION OF INSIDE LEVER Press the button below ''SWITCH'' mark of the interior assembly to free inside lever and turn it upward then down to the correct horizontal direction with the door. Lever will be fixed in position after a sound of ''click''. Follow the page 10 to determine the direction of the lever.
INSTALLATION INSTRUCTIONS 6-2. TO RESET DIRECTION OF OUTSIDE LEVER Use a screwdriver to press the button in the hole below ''SWITCH'' mark of the exterior assembly to free outside lever and turn it upward and then down to the correct horizontal direction with the door. Lever will be fixed in position after a sound of ''click''. Follow the page 11 to determine the direction of the lever.
INSTALLATION INSTRUCTIONS 7-1. MOUNTING EXTERIOR ASSEMBLY A. Slide the spindle and screw posts through the latch and thread the cable under the latch. B. Thread the cable through the rectangular hole in the mounting plate and combine the posts of the mounting plate and the exterior assembly. C. Fasten the mounting plate with 2 screws (32mm or 1 1/4'') while ensuring the exterior assembly is held in the ''true vertical'' position on door face.
INSTALLATION INSTRUCTIONS 7-2. PREPARING TO MOUNT INTERIOR ASSEMBLY A. Remove battery pack cover by pushing it up to the top position.(Please follow two steps ) B. Remove the lever by inserting the catch tool into the access hole and depressing to release catch while gently pulling on lever. Once catch has been released, remove the catch tool from the access hole to allow the lever to pull off completely.(Please follow two steps ) C. Follow the steps on page 16 to remove the decorative cover.
INSTALLATION INSTRUCTIONS 7-3. REMOVING DECORATIVE COVER A. Remove decorative cover by holding fingers at cover's edges as shown in photo A. B. Use thumbs to press ''THUMBTURN'' as shown in photo B and photo C.
INSTALLATION INSTRUCTIONS 7-4. MOUNTING INTERIOR ASSEMBLY A. Insert the cable into the connector port firmly with blue wire just under the red black wires of the port as shown. B. Slide the interior assembly onto square spindle of the exterior assembly. C. Fasten the interior assembly on the mounting plate with 2 screws (7.8mm or 0.3'').
INSTALLATION INSTRUCTIONS 7-5. BATTERY INSTALLATION A. Snap the decorative cover back onto the interior assembly. B. Place four alkaline batteries into the battery pack. Following the imprinted '' +/- '' guide. C. Replace the battery pack cover as shown.
INSTALLATION INSTRUCTIONS 7-6. REINSTALL LEVER Reinstall the lever after the decorative cover is snapped back onto the interior assembly. NOTE: If you follow page 10-13 to change inside and outside levers to proper direction, you can skip the following instructions about exchange of lever to setup mode started in page 28.
INSTALLATION INSTRUCTIONS 8-1. EXCHANGE OF LEVER For lever removal and assembly process, please see page 21-25.
INSTALLATION INSTRUCTIONS 8-2. EXCHANGE OF LEVER (REMOVAL OF INSIDE LEVER) Insert the catch tool into the access hole on the lever. Once the lever is released, remove the catch tool and pull the lever off.
INSTALLATION INSTRUCTIONS 8-3. EXCHANGE OF LEVER (REMOVAL OF OUTSIDE LEVER) A. Insert the key horizontally and turn counter-clockwise 90 degrees. B. Insert the catch tool into the access hole on the lever. Once the lever is released, remove the catch tool and pull the lever off. NOTE: This step is required if you are rekeying the lock.
INSTALLATION INSTRUCTIONS 8-4. SWAP INSIDE AND OUTSIDE LEVERS (REMOVAL OF CYLINDER) A. With lever removed, withdraw the key. B. Slide the cylinder retaining collar off the shank of the lever. C. Remove the cylinder. D. Insert cylinder into the other lever. Align the tab of the cylinder retaining collar with the slot of lever shank and push it back to secure cylinder in place.
INSTALLATION INSTRUCTIONS 8-5. SWAP INSIDE AND OUTSIDE LEVERS (ASSEMBLE OUTSIDE LEVER) A. Turn the key counter-clockwise by 90 degree to vertical position as shown. B. Push outside lever back to slide onto spindle until it is securely engaged.
INSTALLATION INSTRUCTIONS 8-6. SWAP INSIDE AND OUTSIDE LEVERS (ASSEMBLE INSIDE LEVER) Align inside lever and push it back to slide onto spindle until it is securely engaged.
MAIN OPERATING INSTRUCTIONS 1.Indicator 4.Confirm Button 2.Keypad 6.Thumbturn (Auto-Locked/ Unlocked switch) 3.Cancel Button 7.Low Battery Indicator 5.
MAIN OPERATING INSTRUCTIONS 27
SETUP MODE IMPORTANT: The internal thumbturn enables/disables exterior lever. The internal thumbturn is horizontal position to be unlocked (passage lock). The internal thumbturn is vertical position to be auto-locked (entry lock). 1. CHANGE PROGRAMMING CODE (THIS PROGRAMMING CODE MUST BE 6-DIGITS IN LENGTH) (1) The pre-set programming code of the product is 123456, please change it before operating the lockset. (2) Keep a written copy of programming code in a safe place.
SETUP MODE 2. ADD A USER CODE (MAXIMUM 100 SETS USER CODES WITH 4-8 DIGITS IN LENGTH.) Procedures: (1) Rotate the internal thumbturn to horizontal position press # (the red indicator is on, you are in setup mode) (2) Input programming code press# press 20 press# enter new user code press # enter new user code press # ...may input 100 sets of user code consecutively (the red indicator is off in 10 seconds).
SETUP MODE 4. DELETE ALL THE EXISTING USER CODES AT ONCE Procedures (1) Rotate the internal thumbturn to horizontal position press # (the red indicator is on, you are in setup mode) (2) Input programming code press# press 40 press# press and hold C (for 3 seconds) until a beep is heard. (This will delete all the user codes EXCEPT the programming code) 5.
SETUP MODE 6.DISABLE BUTTON SOUND (MUTE MODE) Procedures (1) Rotate the internal thumbturn to horizontal position press # (the red indicator is on, you are in setup mode) (2) Input programming code press# press 60 press#. (Please repeat the above procedures to enable the button sound) 7.
OPERATION MODE 1. TO ACTIVATE 10-3. TO LOCK AUTO-LOCKING (AUTOMATIC RE-LOCKING) A. Use a flat tool to turn the thumbturn on the inside to vertical position as shown to activate auto-locking mode, i.e., this device will be relocked automatically in 5 seconds (default value) after unlocking. Then outside lever is free turning without retracting latch to open the door. B. Turn the thumbturn on the inside to horizontal position as shown to deactivate auto-locking mode.
OPERATION MODE 2. TO OPEN (UNLOCK) THE DOOR A. Enter the correct user code or programming code. B. Upon the green indicator light on and a short beep heard, turn the outside lever to unlock.
OPERATION MODE 3. TO DEACTIVATE AUTO-LOCKING (AUTOMATIC RE-LOCKING) Use a flat tool to turn the slotted turn on the inside as shown from vertical position to horizontal position to deactivate auto-locking mode. The device is then served as a passage lever.
TROUBLESHOOTING GUIDELINE Problem Solutions A. Keypad does not respond 1. Check to see if the batteries are properly installed. 2. Check to see if the indicator is flashing. It means "the battery is low" if the indicator keeps flashing. 3. Make sure the cable is well-connected to the port. 4. Please contact us if such problem could not be solved. B. Can not change programming code 1. Complete the "CHANGE PROGRAMMING CODE" process by inputting codes within 10 seconds. 2.
TROUBLESHOOTING GUIDELINE Problem E. Can not open the door after input a correct user code F. Yellow indicator is on or keeps flashing Solutions 1. Make sure you have entered the correct user code. 2. Check to see if the indicator is flashing. If the indicator is flashing, please replace the batteries with new ones. 3. Please make sure the strike plate is installed correctly if you see the latch is jammed. 1. It means these batteries are getting low, please replace all the batteries. 2.
DATA RECORDS SECURITY INSTRUCTIONS 1. Do not share your programming code with anyone else. 2. Keep a written copy of all valid user codes in safe place. (You may use the table below to record your information) 3. Code capacity: 100 sets maximum. 4. You are advised to re-program all codes if you lost any security information of the lever lock.
FEDERAL COMMUNICATIONS COMMISSION STATEMENT This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC REGULATIONS This Class B digital apparatus complies with Canadian ICES-003 . Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. This device complies with Industry Canada licence-exempt RSS-210 standard. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.
Rev.
