LAVE-VAISSELLE
Chère cliente, cher client, conservez cette notice d’utilisation avec l’appareil. Si l’appareil devait être vendu ou cédé à une autre personne, assurez-vous que la notice d’utilisation l’accompagne. Le nouvel utilisateur pourra alors être informé du fonctionnement de celui-ci et des avertissements s’y rapportant.
Sommaire Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Protection de l’environnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Laver la vaisselle de manière économique et ménageant l’environnement . . . . . . . . . . . . . . . . . . . . . . . 7 Vue de l’appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sommaire Instructions d’installation et de raccordement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Mise en place du lave-vaisselle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Montage de la plaque décor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Raccordement du lave-vaisselle . . . . . . . . . . . .
Consignes de sécurité La sécurité des appareils électroménagers FAURE est conforme aux Règles reconnues de la technique et à la législation portant sur la sécurité des appareils. En tant que fabricant, nous attirons cependant votre attention sur les indications supplémentaires suivantes: Sécurité générale Installation, raccordement, mise en service • • • • • Le lave-vaisselle peut uniquement être transporté debout. Contrôlez le lave-vaisselle pour dégâts de transport éventuels.
• • – L’appareil doit également rester raccordé à l’alimentation électrique lorsqu’il n’est pas en service. – Le lave-vaisselle doit être installé correctement. – Fermez toujours le robinet d’arrivée d’eau lorsque le lave-vaisselle n’est pas utilisé. Ne montez pas et ne vous placez pas sur la porte ouverte de l’appareil, celui-ci pourrait basculer. En cas d’anomalie, fermez le robinet d’arrivée d’eau, puis débranchez la prise de courant.
Laver la vaisselle de manière économique et ménageant l’environnement • • • • • • Ne raccordez le lave-vaisselle à une alimentation en eau chaude que si vous disposez d’une installation d’eau chaude qui ne chauffe pas à l’électricité. Réglez correctement l’adoucisseur. Ne rincez pas préalablement la vaisselle à l’eau courante.
Vue de l’appareil Arrosage Joint en caoutchouc pour le couplage du tuyau d’arrivée d’eau au bras de lavage supérieur.
Bandeau de commande Touches de fonction 1 2 3 4 Voyants Zone de commande La zone de commande se compose de la touche MARCHE/ARRET et des touches de programme avec leurs voyants.
Adoucisseur d'eau Suivant les localités, l’eau contient une quantité variable de sels calcaires et minéraux. Ceux-ci se déposent sur la vaisselle laissant des taches et des dépôts blanchâtres. Plus la teneur en sels est élevée et plus l’eau est « dure ». Le lave vaisselle est muni d’un adoucisseur et, utilisant du sel régénérant spécial pour lave vaisselle, il fournit une eau dépourvue de calcaire (adoucie) pour opérations de lavage.
2. Maintenez simultanément les touches de fonction 1 et 2 enfoncées. Les voyants correspondants aux touches de fonction 1 à 3 clignotent 3. Appuyer de nouveau sur la touche de fonction 1 . Le voyant lumineux de la touche de fonction 1 clignote. Au même moment, le voyant lumineux correspondant à la phase de programme FIN clignote : – Le nombre de signaux clignotants du voyant lumineux correspondant à la phase de programme FIN se rapporte à la dureté sélectionné.
Le sel régénérant 3 Si la dureté de votre eau correspond aux degrés de niveau 1, il n’est pas nécessaire d’utiliser du sel régénérant car elle est déjà douce. Il existe 2 façons différentes d’utiliser le sel régénérant : • • Si vous utilisez du produit de lavage pour lave vaisselle qui contient du sel celui-ci doit être déposé dans le réservoir du produit de lavage. – Dans ce cas, l’adoucisseur d’eau doit être réglé manuellement sur 0 et automatiquement sur 1.
3 Si vous utilisez un produit de lavage contenant du sel régénérant, le réglage automatique de l´adoucisseur d‘eau sur “1” permet de désactiver le voyant de contrôle sel. Remplissage du réservoir de sel régénérant Si vous utilisez séparément un produit de lavage et du sel régénérant, versez le sel spécifique : • Avant la première utilisation du lave-vaisselle. • Quand le voyant de contrôle SEL s’allume sur le bandeau de commande. 1. Ouvrez la porte, retirez le panier inférieur. 2.
Le produit de rinçage Ce produit évite que l’eau ne reste sur la vaisselle sous forme de gouttelettes laissant des taches blanches après séchage. Il existe deux façons différentes d’utiliser le produit de rinçage : • • Si vous utilisez un produit de lavage contenant déjà un produit de rinçage, versez-le dans le distributeur de produit de lavage. – Dans ce cas, le distributeur de produit de rinçage doit être désactivé.
Remplissage du distributeur de produit de rinçage Si vous utilisez séparément du produit de lavage et du produit de rinçage, versez le produit de rinçage : – Avant la première utilisation du lave-vaisselle. – Quand le voyant de contrôle PRODUIT DE RINCAGE s'allume sur le bandeau de commande. Le réservoir de produit de rinçage se trouve sur la face intérieure de la porte du lave-vaisselle. 1. Ouvrez la porte. 2. Appuyez sur la touche de déverrouillage du réservoir de produit de rinçage. 3.
Activer ou désactiver le signal sonore Il est possible d‘ajouter un signal sonore aux voyants lumineux (par ex. en fin de programme ou en cas d'erreurs). 1. Ouvrir la porte du lave-vaisselle. 2. Appuyez sur la touche MARCHE/ARRET. Le voyant correspondant à la touche MARCHE/ ARRET s´allume. Si d´autres voyants s´allument, un programme de lavage est activé. Désactivez le programme de lavage (RESET) : Appuyez simultanément sur les touches de fonction 1 et 2 pendant environ 2 secondes.
Utilisation journalière • • • • • Faut-il compléter le sel régénérant ou le produit de rinçage? Disposez les couverts et la vaisselle dans le lavevaisselle Remplissez le réservoir de produit de lavage pour lave-vaisselle Sélectionnez un programme de lavage convenant aux couverts et à la vaisselle Lancez le programme de lavage Disposez les couverts et la vaisselle 1 Les éponges, serviettes de ménage et tous les objets susceptibles de se saturer en eau, ne peuvent pas être lavés au lave-vaisselle.
Panier à couverts 1 Ne placez pas de pièces longues dans le panier à couverts. Cela pourrait bloquer le bras de lavage et être une source de danger, en particulier pour les enfants. Ils doivent pour cette raison être placés dans le panier supérieur. Afin que chaque face de couverts puisse être aspergée d’eau, vous pouvez 1. insérez l’élément grille sur le panier à couverts 2. placez les couteaux courts, les fourchettes et les cuillères avec la poignée vers le bas sur la grille du bac à couverts.
Disposition de la vaisselle (casseroles, poêles et grandes assiettes) Placez les grandes pièces de vaisselle très sales dans le panier inférieur. Votre lave-vaisselle dispose de l'une des deux variantes de panier inférieur suivantes Variante 1 : le support à assiettes à l'arrière du panier inférieur est extractible 3 Afin de placer plus facilement les récipients les plus grands, il est également possible - de retirer le support à assiettes arrière du panier inférieur.
Disposition de la vaisselle (tasses, verres, …) Placez les petites pièces de vaisselle, fragiles et les longs couverts dans le panier supérieur. • • • • Disposez les pièces de vaisselle en quinconce sur les supports à tasses amovibles et en dessous de ceux-ci afin que l’eau de lavage atteigne toutes les pièces de vaisselle. Pour les pièces de vaisselle hautes, rabattez les supports à tasses.
Remplissage du produit de lavage 1 N’utilisez que des produits de lavage pour des lave-vaisselle ménagers. Le produit de lavage est dangereux! Le réservoir de produit de lavage doit être rempli avant chaque programme de lavage, à l’exception du programme prélavage. Le produit de lavage est libéré automatiquement au cours du programme de lavage. 2 Veuillez respecter les recommandations de dosage et de stockage du fabricant mentionnées sur les emballages des produits de lavage.
Utilisation des tablettes de détergent combinées “3 en 1” Recommandations générales Ces produits sont des tablettes qui combinent les fonctions détergent / aide au rinçage et sel. 1. Avant d'utiliser ces produits, vous devriez d'abord vérifier que la dureté de l'eau de votre alimentation en eau est compatible avec l'utilisation de ces produits en vous référant aux instructions fournies par le fabricant du détergent (Voir sur l'emballage). 2.
Sélectionner le programme de lavage (tableau des programmes) Sélectionnez le programme de lavage approprié à l'aide de ce tableau: Type de vaisselle: de plus: Service de table et plats Récipients Service de table sans casseroles et plats avec de la vaisselle sensible à la chaleur – – très sale; restes séchés d'aliments, en particulier blanc d'oeuf et amidon fortement à normalement sale restes séchés d'aliments Programme de lavage approprié: ò ò ò ò ò Enfoncez la touche de programme: INTENSIF 7
Démarrer le programme de lavage 1. Ouvrir la porte du lave-vaisselle. 2. Vérifier que la vaisselle et les couverts sont disposés de manière telle que les bras d´aspersion puissent tourner librement. 3. Ouvrir complètement le robinet d'eau. 4. Appuyer sur la touche MARCHE/ARRET. Le voyant correspondant s´allume. 5. Appuyer sur la touche du programme sélectionné (voir “tableau des programmes”). Le voyant du programme correspondant s´allume. 6. Fermer la porte du lave-vaisselle. Le programme de lavage démarre.
Désactiver le lave-vaisselle Lorsque le signal sonore est activé, un signal continu retentit pendant 15 secondes à la fin du programme de lavage. Lors de l’ouverture de la porte immédiatement après l’arrêt du programme, il se peut que de la vapeur d’eau brûlante s’échappe de l’appareil. C’est pourquoi 1. il faut ouvrir la porte avec précaution. 2. Arrêter le lave-vaisselle à l’aide de la touche MARCHE/ARRET. Tous les voyants s’éteignent.
Entretien et nettoyage 1 Nettoyez régulièrement les surfaces extérieures de l’appareil et le bandeau de commande avec un chiffon doux humide et si nécessaire, uniquement avec des détergents doux. N’employez jamais de produits abrasifs ou de solvants (acétone, trichloréthylène, etc …). Nettoyez les joints d’étanchéité de la porte et les distributeurs de produit de lavage et de rinçage avec un chiffon humide. Nettoyage du filtre 3 Les filtres sont situés au fond de la cuve.
Que faire quand... Si vous constatez une anomalie dans le lavage ou le fonctionnement de votre appareil, consultez les indications données dans cette notice d’utilisation avant de faire appel au Service Après Vente. Dans la majorité des cas, vous pourrez y remédier vous-même. Si malgré toutes les vérifications, une intervention s’avère nécessaire, le vendeur de votre appareil est le premier habilité à intervenir. A défaut (déménagement de votre part, fermeture du magasin où vous avez effectué l’achat...
Après réparation des anomalies signalées par 1 ou par 2 signaux sonores, appuyer sur la touche du programme de lavage en cours. Le programme de lavage se poursuit. Si le dérangement se reproduit, veuillez contacter le service après vente. 3 Pour tout autre dérangement, veuillez contacter le service après-vente et leur décrire le type d’anomalie (voir chapitre service aprèsvente). ... vous avez des problèmes lors de l’utilisation du lave-vaisselle. Symptômes Le programme ne démarre pas.
Caractéristiques techniques Capacité: 12 couverts normalisés y compris vaisselle de service Pression d’eau autorisée: 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Raccordement électrique: Les informations concernant le raccordement électrique se trouvent sur la plaque signalétique placée sur le côté droit de la porte du lave-vaisselle. Lave-vaisselle: «pose-libres» Dimensions: 850 x 600 x 600 (H x L x P en mm) poids max.
Indications à l'attention des instituts d'essai L'essai selon la norme EN 60704 doit être effectué à pleine charge avec le programme de test (voir tableau des programmes). Les essais selon la norme EN 50242 doivent être effectués avec le bac à sel de l'adoucisseur d'eau plein, avec le bac d'alimentation du produit de rinçage plein et avec le programme de test (voir tableau des programmes).
Exemple de rangement: Panier à couverts Certains modèles de lave-vaisselle possèdent des paniers à couverts non équipés d'une grille.
INSTRUCTIONS D’INSTALLATION ET DE RACCORDEMENT Mise en place du lave-vaisselle • • • • • Le lave-vaisselle doit être mis correctement d’aplomb et de niveau. Dévisser les pieds réglables afin de compenser les inégalités du sol et d'adapter la hauteur de l'appareil aux meubles adjacents : – à l'aide d'un tournevis. Pour les lave-vaisselle sur socle indépendant, intégrables et encastrables, les pieds arrières de l'appareil doivent être réglés de l'avant de l'appareil à l'aide d'un tournevis.
Raccordement du lave-vaisselle Arrivée d'eau Le lave-vaisselle possède des dispositifs de sécurité qui empêchent le reflux de l'eau de lavage dans le réseau de distribution d'eau potable et sont conformes aux prescriptions de sécurité en vigueur en matière de sécurité hydraulique. • Le lave-vaisselle peut être alimenté en eau froide et en eau chaude jusqu'à 60 °C max. • Le lave-vaisselle ne peut pas être raccordé à un chauffe-eau.
3 Le chapitre suivant concerne uniquement les lave-vaisselle qui ont un clapet de sécurité au raccord vissé au niveau du robinet d’eau : Tuyau d’alimentation avec clapet de sécurité Après avoir raccordé le tuyau d’alimentation à double conduit, le clapet de sécurité se situe directement au contact du robinet. De ce fait, le tuyau d’alimentation n’est sous pression que pendant l’alimentation en eau.
Evacuation de l’eau Tuyau d’évacuation Le tuyau d’évacuation ne peut être ni plié, ni écrasé ni replié sur lui-même. Raccordement du tuyau d’évacuation: – hauteur maximum: 1 mètre. – hauteur minimum nécessaire, 40 cm. 1 • Tuyaux de prolongement • • Les tuyaux de prolongement sont disponibles chez votre magasin vendeur. Le diamètre intérieur des flexibles de prolongement doit être de 19 mm.
Système de protection contre les fuites d’eau A titre de protection contre les dégâts des eaux, le lave-vaisselle est équipé d’un système de protection contre les fuites d’eau. En cas d’anomalie, la soupape de sécurité dans le tuyau d'alimentation interrompt immédiatement l’arrivée d’eau et la pompe d’évacuation se met en marche. De cette manière, l’eau ne peut ni s’écouler ni déborder. L’eau résiduelle se trouvant dans l’appareil est évacuée automatiquement par pompage.
Technique de raccordement Les tuyaux d’alimentation en eau et d’évacuation ainsi que le câble d’alimentation électrique se raccordent sur le côté du lave-vaisselle, aucune place n’étant disponible à cet effet à l’arrière de l’appareil. L’exemple suivant d’une installation sanitaire et électrique ne peut constituer qu’une recommandation, les circonstances locales étant déterminantes (raccordements disponibles, prescriptions locales de raccordement des sociétés de distribution d’eau et d’électricité, etc.).
SERVICE au chapitre «Que faire si...» sont rassemblées les sources de panne les plus fréquentes, auxquelles vous pouvez remédier vous-même. Si vous faites malgré tout appel au service aprèsvente pour un des problèmes mentionnés ou suite à une erreur de manipulation, la visite du technicien de service après-vente ne sera pas gratuite pendant la période de garantie non plus. Si vous ne trouvez pas d’indication pour une panne dans ce mode d’emploi, veuillez vous adresser au service après-vente.
ANC 822 960 028 - 00 - 0103