User’s Manual v1.0.0.0 F740 A/2013 www.favite.
[鍵入文字] Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
[鍵入文字] The product shall be installed at a location where the radiating antenna can be kept 22cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3. External antenna Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited. 4. Installation procedure Please refer to user’s manual for the detail. 5.
F740 User Guide Table of Contents 1. Introduction ........................................................................................................... 1 1.1 Overview .......................................................................................................... 1 1.2 Requirement...................................................................................................... 1 1.3 Reference Documents ....................................................................................
F740 User Guide Tables Table 1: Reference Documents ...................................................................................... 2 Table 2: Specification of the F740 ................................................................................. 3 ii C 2013, Favite, Inc v2.2.1.
F740 User Guide 1. Introduction This user’s manual guide is providing instruction for installing and operating the F740 RFID reader. This document is designed for use by RFID system integrators and software developer who develops relatively program and extended systems that take full advantage of the RFID Reader's capabilities. 1.1 Overview F740, one of FAVITE RFID reader family, is an Intel ATOM CPU based smart reader.
F740 User Guide 1.3 Reference Documents Table 1: Reference Documents Reference Document Version EPC Class-1 Gen-2 UHF RFID Protocol for communications at 850-960MHz FAVITE FS-GF801 GPIO Programming Guide DotNet CSharp (optional) 2.0.0.0 FAVITE SDK Getting Started Guide CSharp WinCE (optional) 2.0.1.0 FAVITE Saturn 7 AP User Guide (optional) 2.2.0.0 FAVITE FS-GF801Recover Guide (optional) 1.0.0.1 FAVITE SCO Protocol User Guide 1.1.1.0 FAVITE Scorpio Tool User Guide 1.1.1.
F740 User Guide 1.
F740 User Guide Software Operation System Linux with SCO server General Characteristics Dimension 500mm x 245 mm x 50.49mm Weight 2.5 Kg Base Material Die-cast aluminum Mounting Wall mounting, vertical placement Power Input DC 19V +- 0.5V / 1.5A @ 33dBm Power Consumption 28.5 W (Typical) Communication USB USB2.0 Ethernet 10/100 Base-T (RJ-45) GPIO 4 digital input, 4 digital output 4 C 2013, Favite, Inc v2.2.1.
F740 User Guide Mechanical: Reader Physical Size Figure 1: F740 Reader Physical Size 5 C 2013, Favite, Inc v2.2.1.
F740 User Guide 6 C 2013, Favite, Inc v2.2.1.
F740 User Guide Figure 2: F740 Reader I/O Terminal GPIO RS232 reset RJ45 USB2.0 FTDI com port power Figure 3: Antenna Port Terminal Interface Antenna1 Antenna2 Antenna3 Antenna4 power link error Figure 4: F740 GPIO Pin definition and I/O description. Pin definition 7 C 2013, Favite, Inc v2.2.1.
F740 User Guide D-SUB15pin V1 GPIO_O1 GPIO_O2 GPIO_I1 GPIO_I2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 GND-1 V2 GND-2 GPIO_O3 GPIO_O4 GPIO_I3 GPIO_I4 GPIO GPIO-OUT Circuit diagram (add figure#) V2 R95 VDD3.3VGP R94 4K7/4 GPIO_OUT4 U13 1 4 2 3 UPC817 47K/6 GND-2 GPIO_O4 GPIO-IN Circuit diagram(add figure#) VDD3.3VGP R96 V2 4K7/4 GPIO_IN4 4 U14 3 GND 1 R98 C68 0.1uF/4 2 47K/6 R99 GPIO_I4 10K/6 UPC817 Note: Please add the 4k7 electric resistances.
F740 User Guide If user wants F740 to receive data from other device through GPIO, please connect 24V power source to PIN19 or PIN20 and connect the device output line to Pin 1~ Pin8. The development of programming of receiving data from GPIO could reference the document “FAVITE F740 GPIO Programming Guide_DotNet CSharp” for read data from GPIO with application method. If user wants F740 to transmit data to other device though GPIO, please connect to Pin 9~ Pin 16.
F740 User Guide Figure 6: F740 (2) Figure 7: FS-GF740 Power Supply and Adapter cable 10 C 2013, Favite, Inc v2.2.1.
F740 User Guide 2.2 Diagnostic LEDs The F740 is including diagnostic LEDs on the face of the reader to provide easy and convenient external indication for various operating conditions: POWER (green) – indicates that power is applied to the reader. Read (yellow) – indicates that the reader is receiving data from a tag. Fault (red) – indicates that a fault condition like CRC check error. debug (blue) – indicates that the F740 is into debug mode 11 C 2013, Favite, Inc v2.2.1.
F740 User Guide Figure 8: FS-GF801 Reader Diagnostic LEDs 12 C 2013, Favite, Inc v2.2.1.
F740 User Guide Antenna Panel The antenna panel is containing four coax antenna connector ports, which isTNCconnector, as shown below. These are TNC connectors. CAUTION: Reader antennas should be positioned so that personnel in the area for prolonged periods may safely remain at least 23 cm (9 in) in an uncontrolled environment from the antenna’s surface.
