FSC-BT691 Datasheet S BLE 5.1 Single Mode Bluetooth Module Datasheet Version 1.1 Shenzhen Feasycom Technology Co.,Ltd -1- www.feasycom.
FSC-BT691 Datasheet Copyright © 2013-2020 Feasycom Technology. All Rights Reserved. Feasycom Technology reserves the right to make corrections, modifications, and other changes to its products, documentation and services at anytime. Customers should obtain the newest relevant information before placing orders. To minimize customer product risks, customers should provide adequate design and operating safeguards.
FSC-BT691 Datasheet 1. INTRODUCTION ............................................................................................................................................................... 3 2. GENERAL SPECIFICATION ................................................................................................................................................. 5 3. HARDWARE SPECIFICATION ............................................................................................................
FSC-BT691 Datasheet integrating a 2.4 GHz transceiver and an ARM® Cortex- TX: 3.5 mA, RX: 2.2 mA (system currents with DC-DC, VBAT_HIGH =3 V and 0 dBm) Programmable transmit output power from M0+TM microcontroller with a RAM of 48 kB and a One-Time Programmable (OTP) memory of 32 kB. -19.5 dBm to +2.5 dBm It can be used as a standalone application processor or as -94 dBm receiver sensitivity a data pump in hosted systems.
FSC-BT691 Datasheet 2. General Specification Table 1: General Specifications Categories Wireless Specification Features Implementation Bluetooth Version Bluetooth Low Energy 5.1 Frequency 2.400 - 2.483.5 GHz Transmit Power -19.5 dBm to +2.
FSC-BT691 Datasheet 3. HARDWARE SPECIFICATION 3.1 Block Diagram and PIN Diagram RF 20 GND 19 1 PIO8 PIO11 18 2 PIO9 PIO5 17 3 NC NC 16 4 NC PIO7 15 5 PIO6 NC 13 7 VDD NC 12 8 GND NC 11 PIO2 14 PIO10 PIO2 PIO10 6 9 10 Figure 2: FSC-BT691 PIN Diagram(Top View) 3.
FSC-BT691 Datasheet ADC1 SWDCLK 11,12 I NC Alternative Function: Analog to Digital Converter input 1. Alternative Function: JTAG clock signal (by default). NC (Do not connect to any pin) 15 PIO7 ADC3 I/O I Programmable input/output line Alternative Function: Analog to Digital Converter input 3. 16 NC 17 PIO5 I/O Programmable input/output line 18 PIO11 I/O Programmable input/output line 19 GND Vss Power Ground 20 RF NC (Do not connect to any pin) O RF signal output .
FSC-BT691 Datasheet 4.4 General Purpose Digital IO There are 6 general purpose digital IOs defined in the module. All these GPIOs can be configured by software to realize various functions, such as button controls, LED drives or interrupt signals to host controller, etc. Do not connect them if not use. The I/O type of each I/O pins can be configured by software individually as Input or Push-pull output mode.
FSC-BT691 Datasheet recommend that you adhere to the correct CTS/RTS handshaking protocol for proper operation. Table 3: Possible UART Settings Parameter Possible Values Baudrate Minimum 1200 baud (≤2%Error) Standard 115200bps(≤1%Error) Maximum 921600bps(≤1%Error) Flow control RTS/CTS, or None Parity None, Odd or Even Number of stop bits 1 /1.5/2 Bits per channel 5/6/7/8 When connecting the module to a host, please make sure to follow .
FSC-BT691 Datasheet 5. ELECTRICAL CHARACTERISTICS 5.1 Absolute Maximum Ratings Absolute maximum ratings for supply voltage and voltages on digital and analogue pins of the module are listed below. Exceeding these values causes permanent damage. The average PIO pin output current is defined as the average current value flowing through any one of the corresponding pins for a 100mS period.
FSC-BT691 Datasheet Transmitter PRF Output power -19.5 - 2.5 dBm PBW 20dB Bandwidth for Modulated Carrier at 1Mbps - 1.5 - MHz Sensitivity (0.1%BER) @1Mbps - -94 - dBm Receiver RXSENS 6. MSL & ESD Table 7: MSL and ESD Parameter MSL grade: MSL 3 ±2000V ±2500V Human Body Model ESD grade: 7. Value Charged Device Model RECOMMENDED TEMPERATURE REFLOW PROFILE Prior to any reflow, it is important to ensure the modules were packaged to prevent moisture absorption.
FSC-BT691 Datasheet ℃ 250 217 210 A 25 0 B 1 2 C 3 D 4 E 5 6 min Figure 5: Typical Lead-free Re-flow Pre-heat zone (A) — This zone raises the temperature at a controlled rate, typically 0.5 – 2 C/s. The purpose of this zone is to preheat the PCB board and components to 120 ~ 150 C. This stage is required to distribute the heat uniformly to the PCB board and completely remove solvent to reduce the heat shock to components.
FSC-BT691 Datasheet Figure 6: FSC-BT691 footprint 9. HARDWARE INTEGRATION SUGGESTIONS 9.1 Soldering Recommendations FSC-BT691 is compatible with industrial standard reflow profile for Pb-free solders. The reflow profile used is dependent on the thermal mass of the entire populated PCB, heat transfer efficiency of the oven and particular type of solder paste used. Consult the datasheet of particular solder paste for profile configurations.
FSC-BT691 Datasheet 26.9 20 5 2.8 8.2 Max.0.5 15 10 43.5 Max.0.5 no bare copper(exept solder pads for module) 10 no copper and components on any layer no components on any layer 20 10 Applic. PCB do not place any conductive parts in this area Provide solid ground plane(s) as large as possible around Figure 7: Restricted Area (Design schematic, for reference only. area Unit: mm) Following recommendations helps to avoid EMC problems arising in the design.
FSC-BT691 Datasheet Antenna Antenna Non enmitting circuits RF & heat enmitting circuits Non enmitting circuits Digital Part RF & heat enmitting circuits RF_IN RF_IN Digital Part Digital & Analog Circuits Digital & Analog Circuits PCB PCB Figure 8: Placement the Module on a System Board 9.3.
FSC-BT691 Datasheet Antenna Wrong Antenna Antenna PCB PCB PCB Better Best Figure 10: Recommended Trace Connects Antenna and the Module Routing of the RF-connection underneath the module should be avoided. The distance of the micro strip line to the ground plane on the bottom side of the receiver is very small and has huge tolerances. Therefore, the impedance of this part of the trace cannot be controlled. Use as many vias as possible to connect the ground planes. 10. 10.
FSC-BT691 Datasheet Figure 11: Tray vacuum 10.2 Packing box(Optional) * If require any other packing, must be confirmed with customer * Package: 2000PCS Per Carton (Min Carton Package) Figure 12: Packing Box Shenzhen Feasycom Technology Co.,Ltd -17- www.feasycom.
FSC-BT691 Datasheet 11. Warning FCC Statements (OEM) Integrator has to assure compliance of the entire end-product incl. the integrated RF Module. For 15 B (§15.107 and if applicable §15.109) compliance, the host manufacturer is required to show compliance with 15 while the module is installed and operating. Furthermore the module should be transmitting and the evaluation should confirm that the module's intentional emissions (15C) are compliant (fundamental / out-of-band).
FSC-BT691 Datasheet auxiliaire indiquant le CI du module RF, tel que" Contient le module émetteur IC: 23872-FSCBT691 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
FSC-BT691 Datasheet Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15.247 2.3 Specific operational use conditions his transmitter/module and its antenna(s) must not be co-located or operating in conjunction with any transmitter. This information also extends to the host manufacturer’s instruction manual. 2.4 Limited module procedures not applicable 2.
