FSC-BT1026 Datasheet Bluetooth Module Datasheet Version 1.3 Shenzhen Feasycom Technology Co.,Ltd -1- www.feasycom.
FSC-BT1026 Datasheet 1. INTRODUCTION Overview FSC-BT1026x it is a Bluetooth dual-mode module series. It supports a Bluetooth Low Energy and compliant system for audio and data communication. FSC-BT1026x integrates an ultra-low-power DSP and application processor with embedded flash memory, a high-performance stereo codec, a power management subsystem, I2S, LED drivers and ADC I/O in a SOC IC.
FSC-BT1026 Datasheet 2. General Specification Table 1: General Specifications Categories Wireless Specification Features Implementation Chip QCC30XX Bluetooth Version V5.1 Dual-mode Frequency 2.402 - 2.480 GHz Transmit Power +6.221 dBm (Maximum) Receive Sensitivity -96.0 dBm (typ.) π/4 DQPSK receiver sensitivity -89.0 dBm (typ.) 8DPSK receiver sensitivity -100 dBm (typ.
FSC-BT1026 Datasheet Audio Output Power: 1000mV (max) (0dBFS 10K load) Stereo separation (crosstalk): BR/EDR Profiles Bluetooth Low Energy Maximum Connections -80dB(Min) SPP (Serial Port Profile) - Up to 600 Kbps A2DP/AVRCP/HFP/HSP/HOGP/PBAP/SPP Profiles support GATT Client & Peripheral Simultaneous BR/EDR and BLE support BR/EDR up to 7 active slaves Bluetooth Low Energy 1 connection as peripheral , up to 5 connections as central Via UART(TBD) USB(TBD) FW upgrade OTA SPI Supply Voltage Supply VD
FSC-BT1026 Datasheet GND EXT_ANT GND SPK_LP SPK_LN SPK_RP SPK_RN MIC_BIAS MIC_LN MIC_LP NC PIO20 PIO21 VCHG_SENSE CHG_EXT VDD_USB/3.3V_OUT NC/PIO54 NC GND NC/AIO4/LED4 AIO5/LED5 PCM_CLK/PIO16 PCM_IN/PIO19 PCM_OUT/PIO18 PCM_SYNC/PIO17 RESET PCM_MCLK_OUT/PIO15 PIO6 PIO7 PIO8 BT_TX/PIO5 BT_RX/PIO4 BT_CTS/PIO22 BT_RTS/PIO23 LED0/AIO0 LED1/AIO1 LED2/AIO2 PIO3 PIO2 GND NC/PIO52 NC/PIO53 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 MIC_RN MIC_RP VCC_CHG USB_DN USB_DP VDD_IO 1.
FSC-BT1026 Datasheet 5 PCM_IN/PIO19 I/O Programmable I/O line 19. Alternative function: PCM_DIN[0] Note 6 6 PCM_OUT/PIO18 I/O Programmable I/O line 18. Alternative function: PCM_DOUT[0] Note 6 7 PCM_SYNC/PIO17 I/O Programmable I/O line 17. Alternative function: PCM_SYNC Note 6 8 RESET I/O Automatically defaults to RESET# mode when the device is unpowered, or in off modes. Reconfigurable as a PIO after boot. 9 PCM_MCLK_OUT/PIO15 I/O Programmable I/O line 15.
FSC-BT1026 Datasheet 27 PIO20 I/O Programmable I/O line 20. Alternative function: PCM_DOUT[1] Note 5 28 PIO21 I/O Programmable I/O line 21. Alternative function: PCM_DOUT[2] Note 5 29 VCHG_SENSE Charger input sense pin after external mode sense-resistor. High impedance. NOTE: If using internal charger or no charger, connect VCHG_SENSE direct to VCHG. 30 CHG_EXT External charger transistor current control. Connect to base of external charger transistor as per application schematic.
FSC-BT1026 Datasheet Alternative function: Differential right line output, positive 48 AUDIO_HPL_N/ SPK_LN A Headphone/speaker differential left output, negative. Alternative function: Differential left line output, negative 49 AUDIO_HPL_P/ SPK_LP A Headphone/speaker differential left output, positive. Alternative function: Differential left line output, positive 50 GND Vss Power Ground 51 RF_OUT RF Bluetooth transmit/receive.
FSC-BT1026 Datasheet MECHANICAL DETAILS 4. 4.1 Mechanical Details Dimension: Module size: Pad size: Pad pitch: 13mm(W) x 26.9mm(L) x 2.2mm(H) Tolerance: ±0.1mm 13mm X 26.9mm Tolerance: ±0.2mm 1.6mmX0.6mm Tolerance: ±0.2mm 1.0mm Tolerance: ±0.1mm Figure 3: FSC-BT1026 footprint FCC Warning Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 Shenzhen Feasycom Technology Co.,Ltd -9www.feasycom.
FSC-BT1026 Datasheet 2.2 List of applicable FCC rules FCC Part 15.247 2.3 Specific operational use conditions This transmitter/module and its antenna(s) must not be co-located or operating in conjunction with any transmitter. This information also extends to the host manufacturer’s instruction manual. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs It is “not applicable” as trace antenna which is not used on the module. 2.7 Antennas 2.4GHZ PCB antenna; 2dBi; 2.400 GHz～2.500GHz 2.
FSC-BT1026 Datasheet "This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation." "Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FSC-BT1026 Datasheet -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
