User Manual

Installation Instructions
1) For FEBCO Series 825Y
3
⁄4" to 1
1
⁄4" assemblies.
Attach funnel to relief valve, under discharge shield, using
1
⁄2" long bolt.
2) For FEBCO Series 825Y 1
1
⁄2" and 2" assemblies.
Depressurize valve and remove lower cover bolt (through bossed area
on backside of relief valve). Install 1
1
⁄2" long bolt through cover and
tighten. Attach extension spacer to funnel using
1
⁄2" long bolt and nut.
Position funnel over protruding bolt and retain with nut.
3) Thread drain piping into the 1" IPS connection in the drain.
4) The unit should be installed near a floor drain sized to adequately handle
maximum relief port discharge if installed in an indoor installation. Write
or call for FEBCO information chart RVDR (relief valve discharge rates).
IS-F-AGD-Y
INSTALLATION INSTRUCTIONS
Series AGD-Y
Air Gap Drain
Sizes:
3
⁄4" – 2"
IS-F-AGD-Y 1330 EDP# 980011 © 2013 FEBCO
Limited Warranty: FEBCO (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of original shipment.
In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER
WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting
from labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no
control. This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above
limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
WARNING: This product contains chemicals known to the
State of California to cause cancer and birth defects or
other reproductive harm.
For more information: www.watts.com/prop65
A Watts Water Technologies Company
USA: Tel: [phone] • Fax: [phone] • www.FEBCOonline.com
Canada: Tel: [phone] • Fax: [phone] • www.FEBCOonline.ca
WARNING
!
Read this Manual BEFORE using this equipment.
Failure to read and follow all safety and use information
can result in death, serious personal injury, property
damage, or damage to the equipment.
Keep this Manual for future reference.
NOTICE
The air gap drain is not designed to catch the maximum discharge possible
from the relief valve. The installation of FEBCO air gap with the drain line
terminating above a floor drain will handle any normal discharge or nuisance
spitting through the relief valve. However, floor drain size may need to be
designed to prevent water damage caused by a catastrophic failure condi
-
tion. Do not reduce the size of the drain line from the air gap fitting.
NOTICE
This funnel cannot be installed on
3
⁄4", 1" OR 1
1
⁄4" assemblies prior
to S/N A1275.
NOTICE
Drain funnel was not designed to, nor is it able to support drainpipe
weight. Support the drain piping by other appropriate means.
NOTICE
The air gap drain is designed to drain away minimal discharge from the
relief valve port. It is not intended to drain all discharge possible from the
relief valve port.
You are required to consult the local building and plumb-
ing codes prior to installation. If the information in this
manual is not consistent with local building or plumbing
codes, the local codes should be followed. Inquire with
governing authorities for additional local requirements.
WARNING
!