User's Manual
Table Of Contents
- Annex no. 5 (Functional Description - User Manual).pdf
- M90113-10e-PY-B.pdf
- 1 Warnings – Read Before Start-Up!
- 2 Characterization
- 3 Functional Elements
- 4 Mechanical Integration
- 5 Connectors
- 5.1 Connector X1 – Power Supply and MDB Interface
- 5.2 Standby Mode / Wake-Up
- 5.3 Connector X2 – USB Device Interface
- 5.4 Connector X3 – COM 0 (RS232 V.24 Interface)
- 5.5 Connector X4 – USB Host 2 Interface
- 5.6 Connector X5 – Ethernet Interface
- 5.7 Connector X6 - Auxiliary
- 5.8 Connector X7 – USB Host 1
- 5.9 Connector X8 – cVEND SHCR
- 5.10 Connector X9 – COM 2 (RS232 V.24)
- 5.11 SAM Sockets (S1, S2)
- 6 Installation and Setup
- 7 Maintenance and Cleaning
- 8 User Interface
- 9 Technical Data
9 Technical Data
Page 37 of 38
9.2 Radio Approvals
9.2.1 Declaration of Conformity (CE)
Hereby FEIG ELECTRONIC GmbH declares that the radio equipment type cVEND PIN is in compliance
with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
internet address:
https://www.feig.de/en/service/eu-declarations-of-conformity/
9.2.2 Declaration of Conformity (UKCA)
Hereby FEIG ELECTRONIC GmbH declares that the radio equipment type cVEND PIN is in compliance
with Directive No. 1206 Radio Equipment Regulations 2017.
The full text of the UKCA declaration of conformity is available at the following internet address:
https://www.feig.de/en/service/ukca-declarations-of-conformity/
9.2.3 Radio Approval - USA (FCC) and Canada (IC)
Products with corresponding marking on their labels have USA and Canada approval.
Product name:
cVEND PIN
FCC ID:
IC:
PJMCVPIN
6633A-CVPIN
Notice for USA and
Canada
This device complies with Part 15 of the FCC Rules and with
RSS-210 of Industry Canada.
Operation is subject to the following two conditions.
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Unauthorized modifications may void the authority granted under Federal
communications Commission Rules permitting the operation of this device.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
Warning: Changes or modification made to this equipment not expressly approved by
FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment.