User manual
17
en
For your safety.
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
Hand-guided oscillator for use without water supply in
weather-protected environments using the application
tools and accessories recommended by FEIN.
AFSC18Q(SL):
– for sawing wood, plastic, glass-fibre reinforced plas-
tics (GFRP) and for sawing sheet metal (max. 1 mm)
– for removing tile joints and rasping or scraping off tile
grout or carpet remainders
– for sanding or rasping of smaller surfaces.
Special safety instructions.
Hold the power tool by the insulated gripping surfaces
when performing operations where the application tool
could contact hidden wires. Contact with a “live” wire
will also make exposed metal parts of the power tool
“live” and shock the operator.
Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Do not use accessories which are not specifically
designed and recommended by the power tool manufac-
turer. Safe operation is not ensured merely because an
accessory fits your power tool.
Grasp the power tool in such a safe manner that your
body never comes into contact with the application tool,
especially while working with application tools such as
saw blades or other blades pointed toward the grasping
range. Touching sharp tips or cutting edges can lead to
injuries.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses.
Where appropriate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.
Do not direct the power tool against yourself, other per-
sons or animals. Danger of injury from sharp or hot
application tools.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
Use and handling of the battery (battery pack).
To avoid hazardous situations such as burns, fire, explo-
sion, skin injuries, and other injuries when handling the
battery, observe the following instructions:
Character Unit of measurement,
international
Unit of measurement,
national
Explanation
U VVDC voltage
f Hz Hz Frequency
n
S
/min, min
-1
, rpm, r/min /min Rated oscillation rate
° ° Oscillation angle
kg kg Weight according to EPTA-Procedure 01
kg kg Weight of the power tool without battery and
application tool
kg kg Weight of the battery
L
pA
dB dB Sound pressure level
L
wA
dB dB Sound power level
L
pCpeak
dB dB Peak sound pressure level
K...
Uncertainty
m/s
2
m/s
2
Vibrational emission value according to EN 60745
(vector sum of three directions)
m, s, kg, A, mm, V, W,
Hz, N, °C, dB, min,
m/s
2
m, s, kg, A, mm, V, W,
Hz, N, °C, dB, min,
m/s
2
Basic and derived units of measurement from the
international system of units SI.
WARNING
OBJ_BUCH-0000000245-001.book Page 17 Monday, January 25, 2016 10:14 AM