Installation Guide

ManualsBrandsFeiss ManualsCeiling Light Parts7-Light Multi-Port Satin Nickel Canopy

Installation Instructions for

Connect the fixture to a suitable ground in accordance with local electrical codes.

Pull the power line wires out of the junction box and secure the mounting plate to the junction box.

Loosen the set screw on the strain relief using an Allen key.(Do Not Remove)

Feed the fixture cord through the strain relief and canopy.

Determine the fixture height (from the bottom of the fixture shade to top of the canopy) by moving the canopy and strain

relief up or down. When desired height is achieved, tighten the set screw on the strain relief using an Allen key.

Leave 6" of the cord behind the canopy for power connections and cut the excess cord. From the end of the cord, strip the

insulation 4" using a sharp knife. Strip the end of the wires. Repeat steps 1-6 forMake sure not to nick the inner wires.

remaining fixtures except the center fixture.

Feed the center fixture cord through the center strain relief, canopy, threaded nipple and out of the junction box. Shorten

the center pendant cord.

Connect the white fixture wires (square and/or rigid) to the neutral power line wire with a wire nut.

Connect the black fixture wires (round and/or smooth) to the hot power line wire with a wire nut.

Place all wires properly inside the canopy, place the canopy onto the threaded nipple, and secure it in place by screwing

center strain relief onto the threaded nipple. Tighten the set screw on the center strain relief.

For swag hook installation, see section 2A on page 4.

GP I :ENERAL RODUCT NFORMATION

These fixtures are intended to be installed utilizing compliantNEC

junction boxes.

This product is safety listed for damp locations.

CAUTION RISK OF FIRE-

This product must be installed in accordance with

the applicable installation code by a person familiar

with the construction and operation of the product

and the hazards involved.

Use minimum 90°c supply conductors.

7 Port Canopy with Swag Hook

1.0

MPC07

Canopy

JUNCTION

BOX

MOUNTING

PLATE

SET

SCREW

CORD

2 2

THREADED

NIPPLE

ALLEN

KEY

STRAIN

RELIEF

CENTER

CORD

SET

SCREW

THREADED

NIPPLE

ALLEN

KEY

CENTER

STRAIN

RELIEF

THREADED

NIPPLE

SET

SCREW

CENTER

STRAIN

RELIEF

Summary of content (4 pages)

PAGE 1
Installation Instructions for MPC07 7 Port Canopy with Swag Hook MPC07 1.0 Canopy These fixtures are intended to be installed utilizing NEC compliant junction boxes. CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. This product is safety listed for damp locations. Use minimum 90°c supply conductors.
PAGE 2
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne. Utiliser les conducteurs d'alimentation supérieure à 90° c.
PAGE 3
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de suministro mínimo 90° c.
PAGE 4
2A 2 ANCHOR ANCRE ANCLA CEILING PLAFOND TECHO ANCHOR ANCRE ANCLA 3 1 Mark a point on the ceiling near the pendant fixture where the swag hook is to be mounted. 2 Tap the anchor at the marked point into the ceiling up to the threaded portion with a hammer. 3 Screw the anchor in the rest of the way with a Phillips screwdriver. 4 Mount the threaded washer to the anchor with the anchor screw. 5 Screw the swag hook onto the threaded washer.