Installation Instructions

ManualsBrandsFeit Electric ManualsElectronicsBLE Module

Caution:

This device complies with Part 15 of the FCC Rules / Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).Operation is subject to the following two conditions:

(1) this device may not cause harmful interference. (2) this device must accept any interference

received, including interference that may cause undesired operation.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates

uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a

type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce

potential radio interference to other users, the antenna type and its gain should be so chosen that

the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut

fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé

Summary of content (8 pages)

PAGE 1
Caution: This device complies with Part 15 of the FCC Rules / Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 2
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Information for the OEM Integrators This device is intended for OEM integrators only. Please see the full grant of equipment document for restrictions.
PAGE 3
Homekit T82XXLM Contents 1.Introduction ...................................................................................................................... 4 2.Features ........................................................................................................................... 4 3. Applications ..................................................................................................................... 4 4. Module Diagram ............................................................
PAGE 4
1.Introduction The Homekit 82XX module with internal PCB printing antenna is MESH Bluetooth Low Energy (BLE) solution which is fully Bluetooth 4.2 standard compliant and allows easy connectivity with Bluetooth Smart Ready devices. Homekit 82XX module supports BLE slave and master mode operation, including broadcast, encryption, connection updates, and channel map updates. It is RoHS-compliant and 100% lead (Pb)-free.
PAGE 5
4.
PAGE 6
BLE Module4 pins diagram ANT BLE Module VDD Power GND P0_W P1_R 24MHzX TAL P2_G P3_B PCBA top view diagram & Module physical map dimension unit: mm 6 LED Module
PAGE 7
5.Pins Description Pin NAME 1 Inter face I/O Power I Ground - Description DC 3.3V input, Max 3.6V, Min 3.0V VDD 2 Ground GND 3 P0_W PWM0 I/O PWM0 4 P0_R PWM1 I/O PWM1 5 P0_G PWM2 I/O PWM2 6 P0_B PWM3 I/O PWM3 7 ADC ADC ADC 8 UART-RX UART-RX UART-RX 9 UART-TX UART-TX UART-TX 6.
PAGE 8
.Reflow Profile 9.Application Design Note To Be Discussed 10.Antenna Design Influence of GND on Antenna a) The GND interrupts the emission of antenna but is essential. b) RF vertical GND is important in antenna design. c) Normally, the emission rate is improved as more GND is secured and edged GND of antenna is cut.