Installation & Assembly
MODEL S10.5DFL/850/MOT/BZ
WARNING:
This product may represent a possible shock or fire hazard if improperly installed
or attached in any way. Product should be installed in accordance with the owners
manual, current electrical codes and/or the current National Electric Code (NEC).
RISK OF ELECTRIC SHOCK: TURN OFF THE MAIN POWER AT
THE CIRCUIT BREAKER BEFORE INSTALLING.
2-Head Motion Security Flood Light
IMPORTANT SAFETY INSTRUCTIONS AND INSTALLATION GUIDE
SAVE THESE INSTRUCTIONS
READ BEFORE INSTALLATION
FEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.comFEIT ELECTRIC COMPANY | PICO RIVERA, CA, USA | (800) 543-3348 | FAX (562) 908-6360 | www.feit.com
1. J-box (not included)
2. Mounting bar
3. J-box screws (2 pieces)
4. Spacers (2 pieces)
5. Mounting gasket
6. Mounting plate
7. Terminal block
8. Mounting plate screws (2 pieces)
9. Mounting bar screw (1 piece)
10. Fixture body
11. Mounting holes
12. Decorative washers (2 pieces)
13. Decorative nuts (2 pieces)
14. Motion and photocell sensor
PARTS INCLUDED TOOLS REQUIRED
SEALANT
REV006
4. Secure Mounting
Gasket (5) and
Mounting Plate (6)
to Mounting Bar (2)
using Mounting Bar
Screw (9). Do not over-tighten.
4. Secure Mounting
Gasket (5) and
Mounting Plate (6)
to Mounting Bar (2)
using Mounting Bar
Screw (9). Do not over-tighten.
(7)
(3)
(2)(1)
Connect:
Black wire to
“L” input.
Ground wire to
“GND” input.
White wire to
“N” input.
L GND
N
8. Turn power on at circuit breaker or replace the fuse.
EXTERNAL JBOX INSTALLATION
EXTERNAL JBOX
INSTALLATION
FLUSH JBOX
INSTALLATION
2. Install Mounting Bar (2)
to an External J-Box (1)
using provided J-Box
Screws (3). Add Spacer
(4) to eliminate gap
between Mounting Bar
and Mounting Plate.
1. Turn main power off at circuit breaker or fuse box.
3. Extend and feed J-Box wires through openings
on Mounting Gasket (5) and Mounting Plate (6)
as shown below.
6. Position and align the Mounting Holes (11) on
Fixture Body (10) to the Mounting Plate Screws (8).
Secure Fixture Body to Mounting Plate using
Rubber Washers (12) and Decorative Nuts (13).
7. Once fixture is tightly secured to J-Box, apply a
silicone sealant around the base of the fixture to
prevent moisture from reaching the connections.
5. Connect power supply
wires directly to
Terminal Block (7).
Secure wires to
Terminal Block by using
a small screwdriver.
See below.
See detail below
Detail
(12)(11)
(13)
(8)
(10)
(12)(11)
(13)
(8)
(10)
(6)
(5)
(6)
(7)
(5)
(3)
(2)
(1)
(4)(4)
L GND N
Connect:
Black wire to
“L” input.
Ground wire to
“GND” input.
White wire to
“N” input.
L GND
N
8. Turn power on at circuit breaker or replace the fuse.
FLUSH JBOX INSTALLATION
2. Install Mounting Bar (2)
to a Flush J-Box (1)
using provided J-Box
Screws (3). Add Spacer
(4) to eliminate gap
between Mounting Bar
and Mounting Plate.
1. Turn main power off at circuit breaker or fuse box.
3. Extend and feed J-Box wires through openings
on Mounting Gasket (5) and Mounting Plate (6)
as shown below.
6. Position and align the Mounting Holes (11) on
Fixture Body (10) to the Mounting Plate Screws (8).
Secure Fixture Body to Mounting Plate using
Rubber Washers (12) and Decorative Nuts (13).
7. Once fixture is tightly secured to J-Box, apply a
silicone sealant around the base of the fixture to
prevent moisture from reaching the connections.
5. Connect power supply
wires directly to
Terminal Block (7).
Secure wires to
Terminal Block by using
a small screwdriver.
See below.
See detail below
Detail
(9)
L GND N
(6)
(5)
L GND N
(6)
(2) (2)
(4)
(4)
(5)
(9)
L GND N
(4)
(14)
(13)
(12)
(11)
(9)
(10)
(8)
(7)
(6)
(5)
(3)
(2)
THIS SIDE UP
(1)
(4)
(14)
(13)
(12)
(11)
(9)
(10)
(8)
(7)
(6)
(5)
(3)
(2)
THIS SIDE UP
(1)
(4)