3-Axis Stabilized Handheld Gimbal for Camera Instructions Guilin Feiyu Technology Incorporated Company User Manual E N V2.
Catalogue 1.Product Overview 2.Installation 2.1Battery Charging 2.2Battery Installation 2.3Camera Installation 3.Gimbal Balancing 3.1Balance Adjustment of the Tilting Axis 3.2Balance Adjustment of the Rolling Axis 3.3Balance Adjustment of the Panning Axis 4.AK2000 Function / Operation 4.1Handle - Function / Operation 4.2Function 5.App - Download and Connecting 5.1Download and Install Feiyu ON App 5.2Connecting App 6.Advanced Operation 6.1Gimbal Initialization 6.2Firmware Upgrade 7.
1.
2.Installation TIPS (1) Please mount the camera before powering on the gimbal. (2) When the battery is low, please charge the gimbal. (3) When not in use, turn off the gimbal and then remove the batteries. 2.1 Battery Charging Please fully charge the batteries before powering on the gimbal for the first time. Charge the batteries with the charger. Micro USB Cable （not included） 5V / 3A 2.2 Battery Installation Remove the tail cap, open the batteries compartment, and install the batteries correctly.
2.3 Camera Installation 1. Lock the lens support frame with the screw to the quick release plate; 2. Use the thumb screw to lock the camera from the bottom slot of the quick release plate, and slightly adjust the lens support frame after locking the camera; (Select the long/short thumb screw according to the position of the camera to be mounted on the quick release plate) 1 1 2 2 Thumb Screw (Long) Thumb Screw (Short) 3. Press and hold the anti-column； 4.
3.Gimbal Balancing 3.1 Balance Adjustment of the Tilting Axis Adjust the center of gravity of the camera in two steps to the axis of rotation of the tilting axis. (1) Adjust the center of gravity position of the tilting axis up and down: point the camera lens down, adjust cross arm to maintain the level, as shown in figure ①, let go and observe the state of rotation. Adjust the balance via adjust the sliding arm up and down (refer to figure ② ③). * After adjustment, be sure to tighten the lock screw.
(2) Adjust the center of gravity position of the tilting axis forward and backward: point the camera lens horizontal forward, adjust cross arm to maintain the level as shown in figure ①,let go and observe the state of rotation. Loosen the safety lock on the right side of the camera, and adjust the balance by sliding up and down the quick release plate on the bottom of the camera (refer to Figure ② ③). *Be sure to fasten the safety lock after adjustment.
3.2 Balance Adjustment of the Rolling Axis When the balance adjustment of tilting axis completed, the balance of the rolling axis can be adjusted:keep the gimbal socket connector vertical to the ground with the hand -held control handle as shown in figure ①, leave the gimbal powered off and observe the balance. Loosen the lock screw and slide the cross arm left and right to adjust the roll (refer to figure ② ③). * After adjustment, be sure to tighten the lock screw.
3.3 Balance Adjustment of the Panning Axis When the balance adjustment of tilting axis and rolling axis is completed, the balance of the panning axis can be adjusted. Keep the gimbal socket connector in the horizontal position,adjust hand-held panning axis as shown in figure ①,let go and observe the state of rotation. Loosen the lock screw on the panning and slide the vertical arm forward and backward to adjust (refer to figure ② ③). * After adjustment, be sure to tighten the lock screw.
4.AK2000 Function / Operation 4.1 Handle - Function / Operation 1.Touch Screen * Click the option to switch or select the function mode, and slide the screen to the left or right to switch the page. Single tap the power button in the panning follow mode to enter the panning follow mode and rolling follow (rolling follow angle ≤ 60°). Single tap the power button in the follow mode to enter the follow mode and rolling follow (rolling follow angle ≤ 60°).
Screen Interface The load setting is performed according to the camera. Payload Setting Capture Mode Scroll Setting Settings Rotation Time Auto Rotation Click on the touch-screen Slide the touchscreen interface to the right 0-300 g 300-600 g 600-1000g Slide the touchscreen interface up and down Custom 2 1500-2500g Custom 3 >2500g Auto-adapt Custom 1 1000-1500g Select the corresponding scene mode according to the shooting scene.
2.Mode Button Note: The firmware upgrade may occur manual operation function and the actual product features do not match. Please find the latest manual on the official website. Single click Panning Mode / Lock Mode Double click Follow mode Triple click All follow mode Single tap to switch between panning mode and lock mode Under follow mode, single tap to switch to panning mode Enter all follow mode Mode Button 3.
5.Recording Button * Need to connect to the shutter release cable or the camera WiFi (for Camera with WiFi function). Single tap Start shooting / Stop shooting Video Button 6.Shortcut button Long time press Fast follow mode Double tap Reset Long time press the shortcut button, enter the fast follow mode. Double tap the shortcut button, return to panning mode, tilt,roll and pan axis return to initial level. shortcut button 7.
8.Function Button Single tap Return / Lock / Unlock On other interfaces, single tap the function button to return to the main interface. Function Button Single tap the function key on the main interface to enter the locked/unlocked state. 9.
4.2 Function Modes Panning Mode（Default mode） The roll and tilt direction are fixed, and the camera moves according to the left-right movements of the user's hand. Follow Mode The roll direction is fixed, and the camera moves according to the left-right movements, updown movements of the user's hand. Rolling Follow Mode The pan and tilt direction are fixed, and the camera moves according to the left-right movements of the user's hand. All Follow Mode The camera moves according to the user's hand.
Auto-rotation Mode Auto-rotation Mode Parameter Setting Method 1. Enter the Feiyu ON App to set the auto-rotation mode parameters. Enter the parameter setting interface to select the auto-rotation mode for setting. The maximum time setting for panning and tilting rotation time is less than 8 hours, and the maximum setting time for photographing stop time and photographing interval is 59 seconds.
Auto- rotation mode setting (1) Select auto-rotation to enter the auto-rotation mode on the display interface. Payload Setting Capture Mode Scroll Setting Settings Rotation Time procedure 1 Initial point setting Auto Rotation O K (2) Set rotation start position Rotate the panning axis or tilting axis to the start position and stay for half a second, and click OK option on the screen to record the start position.
5.App - Download and Connecting 5.1 Download and Install Feiyu ON App * Requires iOS 9.0 or later, Android 5.0 or later iOS Version Android Version 5.2 Connecting App 1. Turn on the mobile phone Bluetooth and start the gimbal； 2. Open the App, and connect to AK2000 according to the App prompts. After the connection is successful, you can control AK2000 on the App. 16 13 w w w. fe i y u-te ch .
6.Advanced Operation 6.1 Gimbal Initialization You can initialize your gimbal when: (1) When camera is not balance. (2) If not use for a long period of time. (3) In case of extreme temperature variations. (1) Select system settings on the display screen to enter the gimbal calibration. (2) Place the gimbal on the table, and the gimbal automatically initializes. If the display screen prompts that the calibration is successful, the initialization ends, otherwise the initialization fails.
6.2 Firmware Upgrade Connect the gimbal to the Feiyu ON App, to upgrade the firmware through the App. Settings Update Query Update Your Gimbal version is ***, The latest version is ***, Feiyu ON do you want to upgrade? Later Download 18 14 w w w. fe i y u-te ch .
7.Specifications 211.7mm 128mm 258.8mm 424.5mm 182.5mm 40mm 56mm Max. Tilting Range 360° Max. Panning Range 360° Max. Rolling Range 360° Tilting Speed 2°/s ~ 75°/s Operation Time 12 Hours Payload 2800g ( In center of gravity balanced state ) Panning Speed Weight 3°/s ~ 150°/s About 1252g (not including the batteries) 19 14 w w w. fe i y u-te ch .
8.Compatible Cameras for Reference Brand Model Can be equipped with a lens CanonEF 100mm f/2.8L IS USM +Camera hood CanonEF 135mm f/2L USM+Camera hood Canon5DMarkIV CanonEF 85mm f/1.2 L II USM+Camera hood CanonEF 50mm f/1.2L USM+Camera hood CanonEF 35mm f/2 IS USM+Camera hood Canon CanonEF 85mm f/1.2 L II USM+Camera hood Canon5DMarkIII CanonEF 24-105mm f/4L IS USM CanonEF 85mm f/1.2 L II USM+Camera hood CanonEF 16-35mm f/2.8L II USM Canon6DMarkII CanonEF 24-105mm f/4L IS USM CanonEF 50mm f/1.
Brand Can be equipped with a lens Model Sony E 50mm F1.8 Sony E PZ 18-105mm F4 OSS Sony Sony FE 85mm F1.8 Sony α7R3 Sony FE 35mm F1.4 sony FE 24-240mm F3.5-6.3 Sony FE 24-105mm f/4 G OSS Sony FE 12-24mm f/4.0 G Sony A6500 Panasonic SonyFE 28-70mm f/3.5-5.6 OSS 25mm f/1.4 GH5s 35-100mm f2.8 GH4 OLYMPUS M.ZUIKO DIGITAL ED 12mm f/2.0 21 14 w w w. fe i y u-te ch .
Guilin Feiyu Technology Incorporated Company +86(0)773 2320865 Due to software and hardware improvements, your actual product might differ from the descriptions and pictures in this user manual. You can get the latest user manual from the official website. For more information, please visit our official website D I S C L A I M E R Prohibit any user for any illegal purpose. Users will be responsible for all behaviors of purchase and use products.
