Installation Manual

4.1 Balance Tilt Axis
Quick Start Guide
EN V 1.1
3-Axis Stabilized Handheld Gimbal for Camera
Specifications
Theoretical Battery Life
Weight
Payload Capability
Compatible Cameras*
Max. Tilting Range
Max. Rolling Range
Max. Panning Range
Tilt Follow Speed
Pan Follow Speed
14h (well-balanced)
About 1100g
2200g (well-balanced)
Canon, SONY, Panasonic and etc.
230°
360°
360°
2°/s ~ 75°/s
3°/s ~ 150°/s
Quick Start Guide
Please read the detailed manual before you begin.
TIPS
1) Please mount the camera and balance it before Power ON.
2) When the battery is low, please charge the gimbal.
3) When not in use for a long time, power off the gimbal.
4)
Experience the basic features on AK2000S soon after following the steps as below.
2
Position Lock
Each rotating axis has a position lock for convenient balancing and storage. Be sure
to unlock the position locks before using the gimbal.
Stored lock status Balanced lock status
Step 2: Mount camera on ARCA
quick release plate ④ .
TIPS
3
Camera Installation
4
Gimbal Balancing
Step 4: Install lens holder ⑤ to
support lens, and tighten the
thumb screw.
Step 1: Mount quick release plate ① on
fixed plate ②, lock it. Loosen the ARCA
quick release plate safety lock ③, take
out ARCA quick release plate ④.
Step 3: Insert ARCA quick release plate
directly into quick release plate ① ,
tighten the safety lock ③ for ARCA
quick release plate.
⑤
①
③
④
1
Charging
Please fully charge the battery before
power on the gimbal for the first time.
Open the USB rubber cover. Connect the USB 2.0 to
Type-C(C01) cable to charge. Quick charge is available.
Guilin Feiyu Technology Incorporated Company
For more information, please visit our official website
E-mail: [e-mail] Tel: [phone]
www.feiyu-tech.com
Due to software and hardware improvements, your actual product might differ from the descriptions
and pictures in this user manual. You can get the latest user manual from the official website.
* Please download the detailed manual for the specific compatible camera and lens.
①
②
③
④
Arca Quick
Release Plate
Make sure the battery and memory card
are installed before camera installation.
Power Button
① Long press : Power on/off
②
Control the touch screen:
Single tap: Lock/unlock screen/
return to homepage
③ Double tap: Standby mode
Single tap at standby mode:
To wake up the gimbal
Mode Button
Single tap: Switch between
pan mode & lock mode
Double tap: Follow mode
Triple tap: All Follow mode
Shutter Button
Press Halfway: Focus
Single tap:
Photo shooting/video recording
Long press for 5 seconds:
Auto-burst shot
(Press again to quit)
Overview
* This product does not include the camera.
Scan QR code to download detailed manual for more guidance of the gimbal.
Arca Quick
Release Plate
Fixed Plate
1/4 inch Thread Hole
3/8 inch Thread Hole
Joystick
1/4 inch Thread Hole
Tilt Axis
Tilt Axis
Position Lock
Quick Release Plate
Vertical Arm Lock Screw
Bluetooth
Camera Connection
Battery Level
Multifunction Knob Control
Pan Mode
All Follow Mode
All Lock Mode
Follow Mode
Touch Screen
(1) a. Unlock the tilt axis position lock ①, turn the camera lens upwards, and check the gravity
center of camera.
b. Loosen the sliding arm lock screw ②, slide the sliding arm ③ to balance the camera.
c. Tighten the sliding arm lock screw ②, when the camera lens keeps upwards that means
balanced.
(2) a. Place the camera lens forwards, check the gravity center of camera.
b. Unlock the quick release plate safety lock ①, adjust camera position until it can stay stable
at any angles.
c. Lock the safety lock ①. Tilt the camera up or down, if it stays stable, it means balanced.
4.2 Balance Roll Axis
a. Tighten the tilt axis position lock ①, unlock the roll axis position lock ②, check gravity center
of camera.
b. Loosen the cross arm lock screw ③, slide cross arm ④ to balance the camera position.
c. Tighten the cross arm lock screw ③, and tilt the camera to the left or right, if it stays stable, it
means balanced.
1) Before balancing the gimbal, please lock the gimbal at the balanced lock status, and the
lens cover should be removed from the camera and the memory card needs to be inserted
to the camera to complete all the connections to ensure that the camera is ready for
shooting.
2) During balancing the gimbal, make sure the camera and gimbal are all powered off.
3) If it is needed to add accessories after the balance is completed, gimbal needs to be
re-balanced again.
5
Power ON/OFF
Unlock position lock of 3 axis before power on. Long
press power button, release the button until it shows
on display.
4.3 Balance Pan Axis
a. Tighten the roll axis position lock ① after balanced tilt axis and roll axis. Unlock pan axis
position lock ②, loosen vertical arm lock screw ③.
b. Hold the handle aslant to 15°~ 20°, check the camera
's movement. (Roll axis will point
down if not balanced)
c. Slide vertical arm ④ to balance it until the camera stays there at any angles, balance
succeeded.
d. Tighten the vertical arm lock screw ③.
Function Button
Single tap: Switch between
Video/Photo mode
Trigger Button
Press & hold: Follow mode
Double tap: Reset
Triple tap: Selfie mode
(Pan axis turn 180° to shoot)
Safety Lock for Arca
Quick Release Plate
Pan Axis
Lens Holder
Pan Axis Position Lock
Handle
(Built in Battery)
Multifunction Knob
Vertical Arm
Roll Axis
Roll Axis Position Lock
Cross Arm Lock Screw
Thumb Screw
Sliding Arm
Sliding Arm
Lock Screw
Cross Arm
Quick Release Plate Safety Lock
Download the Feiyu ON App
* Requires iOS 9.0 or above, Android 6.0 or above.
Scan the QR code to download the app,or search for "Feiyu ON" in the App Store
or Google Play.
Scan the QR code to get the latest user manual or download it from
the official website
Detailed Manual
https://www.feiyu-tech.com/ak2000s/