FE NIE X . 2017 INSTRUCTION MANUAL W E B. w w w.feniex.com 4200-DL Controller Instruction Manual V.2.0 4200-DL Model # C-4200-DL This instruction manual serves as a guide for the 4200-DL Controller. IMPORTANT! Please read through all provided instructions and any listed warnings in regards to product use. Feniex Product Copyrights This price List and the mentioned Feniex products include or describe copyrighted Feniex material.
Table of Contents Safety Regulations & Warranty Service after Expiration Copyright Feniex Product Copyright TM V2.0 3 3 3 3 Box Contents 4 Control Head Mounting 6 System Specification Vertical Mount Surface Mount Relay Wiring Diagram Configuration Record 5 6 6 7 9 Configuration Record Diagram 10 Control Head Programming 11 Bluetooth 19 Help Bluetooth Hardware Bluetooth Software 4200 App Requirements FAQ 2 11 19 20 20 21 FE NIE X . 2017 INSTRUCTION MANUAL WE B.
TM V2.0 Safety Regulations The following provides all the information necessary to safely operate the previously listed products of Feniex Industries, Inc. Please read this manual thoroughly before installing or operating your new product in order to prevent any damage or injury. Failure to follow the listed instructions in this manual may result in damage to your products or personal injury. • Proper installation of this product requires good knowledge of automotive systems, electronics and procedures.
Box contents USB Cable RJ45 Cable TM V2.0 RJ45 Cable U-Shaped Bracket Slide Switch Legend/ Label Sheets 4 FE NIE X . 2017 INSTRUCTION MANUAL WE B. w w w.feniex.
System Specification TM V2.0 Below you will find the key specifications for the 4200-DL system. Review the information to better determine your installation needs. Warning! Do not deviate from the specified voltage.
Control Head TM V2.0 Decide which mounting option you would like to implement for the 4200 controller: Option A is a vertical mount, allowing the controller to hang down. Option B is a surface mount; with the bracket mounting from the rear of the controller. The controller can also be mounted with a custom face on a console mount. Please contact your preferred console manufacturer for a 4200 console faceplate (option not shown).
relay wiring Diagram TM V2.0 The below is an example illustration of an installation with the 4200 12V- post 60 Amp Fuse Recommended 10-12 AWG Wire Battery 12V+ post Not provided, install 6 inches away from the battery post. 12V- 12V+ 10 Amps WigWag [ 10 Amps WigWag RJ45 12V+ 12V+ 12V+ Controller USB Output 1-4 12V+ 12V+ 12V+ 12V+ Output 5-8 use either RJ45 or USB cable at one time.
relay wiring Diagram TM V2.0 The below image indicates the use of outputs 1 and 2 for wig wag functionality. The below image shows the location of the X5, 30 amp Fuses on the relay. F1 Output 1-4 + Load/Device F2 Output 5-8 F3 Output 9-12 F4 connect here Fog connect here Headlight wig wag BCM Halogen or LED Light Tail Turn Brake Output 13-16 F5 Output 17-20 Output Power RJ45 The below image illustrates the multiple, potential functionality for inputs A-H.
Configuration Record TM V2.0 Use this document to record the products connected to each outlet to assist when programming the control head with the provided software package. Outputs: 3 Buttons: (1 - 18, P1 - P3) 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Inputs: A (-) B (-) C (+) D (+) E (+) F (+Night) G (+Day) H (+Ignition) 9 FE NIE X . 2017 INSTRUCTION MANUAL WE B. w w w.feniex.
Configuration Record diagram 10 FE NIE X . 2017 INSTRUCTION MANUAL WE B. w w w.feniex.com TM V2.
Control Head Programming TM V2.0 To program the Feniex 4200 Controller, first visit www.feniex.com/s-4200 to download the software. Click on "Literature" and select "Software Download" Step 1: Click Run to continue Step 2: Select your location to Install Help For assistance on how to use the software, please click the help button located on the top bar in the software interface. You will find informative videos on how to program every function of the 4200 software system. 11 FE NIE X .
Control Head Programming Step 3: Open the Feniex 4200 Controller software. TM V2.0 Figure 5.1 Step 4: Connect the provided USB wire to the controller, and connect the other end of the USB port to the computer. Figure 5.2 Step 5: When the controller is plugged in, the red box reading "Device Disconnected" will change from Red to Green will read: "Device connected." 12 FE NIE X . 2017 INSTRUCTION MANUAL WE B. w w w.feniex.
Control Head Programming TM V2.0 Ports 1-20 can be activated by: • • • Button Input Slide Switch (p1, p2, p3) Step 6: Activate Ports Select button, input or slide switch and then check the box of the desired port. You can select as many ports as needed with each button programmed. Each output is capable of 10 amps. For any product requiring more than 10 amps, use multiple ports to split the load.
Control Head Programming TM V2.0 Step 7: Activate Button This function programs the slide switch (p1, p2, p3) or inputs A-E to activate a button. Please note a button cannot activate another button. Multiple buttons can be activated through the slide switch or input set up. Step 8: DeActivate Button This function allows any input, slide switch or button to turn off an activated button. For example. Arrow function: Left arrow button #6, right arrow button #8, center out button #7.
Control Head Programming TM V2.0 Step 9: Timer The timer function allows any button to continue functioning for a set period of time after it's been disabled. Timer can be set for any duration between 1 second to 1 hour. This applies for all inputs A-H and all buttons. The slide switch cannot be programmed for timer or momentary functions. The momentary function only applies to buttons and allows a button to activate only when the user holds the button down.
Control Head Programming TM V2.0 Step 10: Siren This function only works when you have a 100W or 200W Storm siren connected. Select the desired switch (input, slide, or button), then select the tone from the drop down menu. If using a 100W siren, only select speaker 1. For 200W sirens, make sure to highlight speaker 1 and speaker 2. Step 11: Audio (under Siren section) This function only works when you have a 100W or 200W Storm siren connected.
Control Head Programming TM V2.0 Step 12: Dual Delay This function works when a 200W Storm siren is connected to the 4200. Dual delay is a check box at the bottom of the siren section. When using a 200W siren and have one switch activating the same siren tone, dual delay will offset the 2 tones so that they alternate. Note: this is only needed when using the same tone and wanting the dual tone functionality.
Control Head Programming TM V2.0 Step 14: Light Bar This function works when you have a full size lightbar connected. To activate a function of the lightbar, select a desired switch (input, slide switch, button) then select the lightbar function. Multiple functions can be selected on 1 switch. 18 FE NIE X . 2017 INSTRUCTION MANUAL WE B. w w w.feniex.
Bluetooth TM V2.0 Bluetooth Hardware The Feniex 4200 has the option of being controlled via a smart phone or tablet. To enable this feature you will require the Feniex in-line Bluetooth module (part #: C-4200WBAD for Android Bluetooth; C-4200WB-AP for Apple Bluetooth). Follow the installation instructions below to pair the 4200 with a smart phone or tablet.
Bluetooth Bluetooth Software Step 3: Upload software to your handheld device. • To download for apple devices, go to the App Store. • To download for android devices, visit the Feniex website at: http://www. feniex.com/s-4200 *The app is not yet available on Google Play Step 4: Turn Bluetooth on using handheld device. Step 5: Press and hold pairing switch button on Feniex Bluetooth device for 3 seconds. 4200 App Requirements: Android App minimum requirements are the following: • Android 2.
FAQ TM V2.0 Fig 7.1 LED / Halogen Bulb C D E High beam Factory Harness (C,D,E) 1. How do I know if there is power to my 4200 Relay? A flashing green LED light on the PCBA will indicate if there is power to the board if the firmware is fully operational. 2. Why can’t I program to outputs 1 - 2? Outputs 1 - 2 are only for the WigWag Function Box. 3. My controller does not turn on after I programmed it? Make sure to provide 12V+ into the "Ignition Input" (Input H). 4.
FAQ TM V2.0 highbeam wire and on the left column of the programmer under "Wig Wag Function" select "high beam" override. 8. My controller button is not illuminating? Make sure to provide 12V+ into Input G (day mode). 9. The program software will not acknowledge my 4200 controller. Make sure the 4200 control panel is plugged in via provided USB to the computer. 10. Can I change button labels on the App for handheld device? Yes. If using Android app, press and hold button on handheld device.