Operation Manual

5
EN
● Neverputthemachinedownonatableor
aworkbenchbeforeithasbeenswitchedoff.
Electrical safety
3
Always check that the voltage of the
power supply corresponds to the voltage
on the rating plate.
● Donotusethemachineifthemainscableor
themainsplugisdamaged.
● Onlyuseextensioncablesthataresuitablefor
thepowerratingofthemachinewith
aminimumthicknessof1.5mm
2
.Ifyouuse
aextensioncablereel,alwaysfullyunrollthe
cable.
Mains plug replacement (UK only)
Ifthemoulded3-pinplugattachedtotheunitis
damagedandneedsreplacing,itisimportantthat
itiscorrectlydestroyedandreplacedbyan
approvedBS1363/5Afusedplugandthatthe
followingwiringinstructionsarefollowed.
Thewiresinthemainscablearecolouredin
accordancewiththefollowingcode:
blue neutral
brown live
Asthecoloursofthewiresinthemainscableof
theunitmaynotcorrespondtothecoloured
markingsidentifyingtheterminalsintheplug,
proceedasfollows:
- Thewirewhichiscolouredbluemustbe
connectedtotheterminalwhichismarkedwith
theletterNorcolouredblack.
- Thewirewhichiscolouredbrownmustbe
connectedtotheterminalwhichismarkedwith
theletterLorcolouredred.
TECHNICAL DATA
PDM1005
Mainsvoltage V~ 230
Mainsfrequency Hz 50
Powerinput W 810
No-loadspeed min
-1
 0-2,600
Impactrate min
-1
 0-41,600
Max.drillbitdiameter
 Wood mm 25
 Concrete mm 13
 Steel mm 10
Protectionclass  IP20
Weight kg 2.2
NOISE AND VIBRATION
PDM1005
Soundpressure(L
pa
) dB(A) 90.4
Acousticpower(L
wa
) dB(A) 103.4
Uncertainty(K) dB(A) 3
Vibration m/s
2
7.79
Uncertainty(K) m/s
2
 1.5
2
Wear hearing protection.
DESCRIPTION (FIG. A)
Yourimpactdrillhasbeendesignedfordrilling
holesinwood,metalandplasticsandforhammer
drillinginbrickandconcrete.
 1. On/offswitch
 2. Lock-onbutton
 3. Speedadjustmentwheel
 4. Forward/reverseswitch
 5. Switchfordrilling/hammerdrilling
 6. Chuck
 7. Maingrip
 8. Auxiliarygrip
 9. Depthstop
10. Chuckkey
11. Chuckkeyholder
ASSEMBLY
4
Before assembly, always switch off the
machine and remove the mains plug
from the mains.

Themachineissuitableforuseofthefollowing
drillbits:
- Wood(HSS)
- Metal(HSS)
- Concrete/masonry(hardmetal)
Mounting
● Placethechuckkey(10)intooneoftheholes
inthechuck(6).
● Openthechuck(6)byturningthechuckkey
(10)counterclockwise.
● Insertthedrillbit(12)intothechuck(6).
● Closethechuck(6)byturningthechuckkey
(10)clockwise.
● Removethechuckkey(10)fromthechuck(6).
Removing
● Placethechuckkey(10)intooneoftheholes
inthechuck(6).