Operation Manual

6
EN
● Openthechuck(6)byturningthechuckkey
(10)counterclockwise.
● Removethedrillbit(12)fromthechuck(6).
● Closethechuck(6)byturningthechuckkey
(10)clockwise.
● Removethechuckkey(10)fromthechuck(6).
Mounting and removing the auxiliary grip

Mounting
● Loosentheauxiliarygrip(8).
● Slidetheauxiliarygrip(8)overthechuck(6).
● Turntheauxiliarygrip(8)totherequired
position.
● Tightentheauxiliarygrip(8).
Removing
● Loosentheauxiliarygrip(8).
● Removetheauxiliarygrip(8)fromthechuck(6).
● Tightentheauxiliarygrip(8).

Thedepthstopisusedtosetthemaximum
drillingdepth.
Mounting
● Loosentheauxiliarygrip(8).
● Insertthedepthstop(9)throughtheholein
theauxiliarygrip(8).
● Setthedepthstop(9)totherequiredposition.
● Tightentheauxiliarygrip(8).
Removing
● Loosentheauxiliarygrip(8).
● Removethedepthstop(9)fromtheauxiliary
grip(8).
● Tightentheauxiliarygrip(8).
USE

● Toswitchonthemachine,presstheon/off
switch(1).Thefurthertheon/offswitch(1)is
pressed,thehigherthespeedofthemachine.
● Toswitchthemachinetocontinuousmode,
keeptheon/offswitch(1)pressedand
simultaneouslypressthelock-onbutton(2).
● Toswitchoffcontinuousmode,presstheon/
offswitch(1)again.
● Toswitchoffthemachine,releasetheon/off
switch(1).

2
Do not change the direction of rotation
during use.
● Forclockwiserotation,slidetheforward/
reverseswitch(4)totheleft.
● Forcounterclockwiserotation,slidethe
forward/reverseswitch(4)totheright.

2
Do not set the speed during use.
● Turnthespeedadjustmentwheel(3)
clockwisetoincreasethemaximumdrilling
speed.
● Turnthespeedadjustmentwheel(3)
counterclockwisetodecreasethemaximum
drillingspeed.

2
Do not change the operating mode
during use.
● Settheswitch(5)toposition„A“fordrilling.
● Settheswitch(5)toposition„B“forhammer
drilling.
Hints for optimum use
● Clamptheworkpiece.
● Firmlyholdthemachinewithbothhands.
● Placethedrillbitontheworkpiece.
● Switchonthemachine.
● Donotapplytoomuchpressureonthe
machine.Letthemachinedothework.
● Switchoffthemachineandwaitforthe
machinetocometoacompletestandstill
beforeputtingthemachinedown.
CLEANING AND MAINTENANCE
4
Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
● Regularlycleanthehousingwithasoftcloth.
● Keeptheventilationslotsfreefromdustand
dirt.Ifnecessary,useasoft,moistclothto
removedustanddirtfromtheventilationslots.
● Regularlycleanthechuckandthedrillbitto
avoidinaccuraciesduringuse.

● Toremovethedrillbit(12),proceedas
describedinthesection
„Mountingandremovingthedrillbit“.