User manual

8
EN
machine type information must be always
visible on machine.
At the end of the sawing process, keep the saw
head downstairs, switch off the machine and
wait until the all moving parts has come to a stop
before you take your hands off the machine.
3. ASSEMBLY AND
ACCESSORIES
Installation of the mitre saw
• Placeonesidebar(21)ontheright-handside
of the machine and the other sidebar on the
left-hand side of the machine.
• Placetheworkpiececlamp(7)ontheleftor
right side of the machine.
• Holdthehandgripandmovethesawslightly
downwards and then pull the pin (5) out slightly
so that saw moves upwards.
Note: Never use the mitre saw without the
extension pieces supplied. Make sure that they
are correctly mounted.
Mounting the anti-tip over support.
• Mountthesupportbracket(24)intotheslotin
the rear of the base.
• Tightenthescrewstosecurethesupport
bracket.
Sliding fence
Fig.2
For safety reasons, this machine is equipped with
a moveable guide fence to used in normal and
bevel cutting.
• Fornormalstraightcross-cutsandmitrecuts,
always adjust the sliding fence (8) to the end
and fix well to provide safety support for work
piece.
• Forbevelcuts,adjusttheslidingfence(8)
to a suitable position as close as to the saw
blade surface but avoid interfere the saw blade
movement and ensure to fix well.
Changing the saw blades
Fig. 4 and 5
Only use saw blades that are sharp and
undamaged. You must immediately
replace chipped or bent saw blades.
DANGER: Do not use any blade larger than the
stated capacity of the saw. It may come into
contact with the blade guard and cause harm.
Do not use a blade too thick to allow the outer
blade washer to engage with the flats on the
spindle. This will prevent the blade screw from
securing the blade on the spindle.
Do not use this saw to cut metal or masonry
• Disconnectthemachinefromthepowersupply.
• Removethescrew(20)thatholdstheretraction
arm to the blade cover.
• Removethescrew(19)inordertoremovethe
bolt-cover by lifting the blade cover (6) upwards.
• Bothsawbladebolt(17)andFlange(18)should
be visible now like shown in fig. 5.
• Pressthesawbladelockbutton(22)Rotatethe
saw blade carefully by hand until the blade locks.
• Usehexkeytoremovethesawbladebolt(17)
by loosening in a clockwise direction.
• RemovetheFlange(18)andthesawblade
• Replacethesawblademakingsurethatthe
arrow marked on the saw blade must point in
the same direction as the arrow shown marked
on the machine. The saw blade teeth must point
downwards.
• Fixthesawbladebolt(17)usethesawblade
lock button (22) in order to secure tightly
• Lowerthebladecover(6)inorderforthebolt-
cover to fall back into place and tighten the
screw (19)
• Attachtheretractionarmbackontotheblade
cover (6) by tightening the screw (20)
• Rotatethesawbladeandcheckiftheguard
operates freely
Adjusting the cutting angle
Fig. 2.
Adjusting Mitre Angles
The mitre angle can be set between 45° left side
and 45° right side
• Loosenthelockingknob(10)
• Pressthelockingpaddle(11)andturnthesaw
table left or right by the locking knob (10) until
the angle indicator (23) indicates the required
angle.
• Releasethelockingpaddle(11)andtightenthe
locking knob (10)
Pre-settings (quick settings) on the following
degrees: -45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°,
30°, 45°.