BASIC SMILE VDS MONITOR INSTALLATION AND USER MANUAL ENGLISH
SMILE SMILE VDS VDS CONGRATULATIONS ON PURCHASING A QUALITY PRODUCT! Fermax electronics develops and manufactures renown systems that meet the highest design and technology standards. Your FERMAX video door entry system will allow you to communicate with the entry panel, see who is calling you and open the front door if you wish. We hope you enjoy its range of functions. www.fermax.com.
SMILE SMILE VDS VDS INDICE - INDEX SMILE MONITOR ......................................................................................................... 4 Measurements: built-in/surface monitor ....................................................... 4 Installing the Monitor ....................................................................................... 5 Wiring ................................................................................................................ 8 Available Functions ..
SMILE SMILE VDS VDS MONITOR MEASUREMENTS: BUILT-IN Measurements in mm. SMILE 7” Monitor 196 196 SMILE 3.5” Monitor 127 209 4,5 4,5 Fermax built-in 3.5” monitor ref. 6546 (Height x Width x Depth.): 186 x 116 x 46 mm Fermax built-in 7” monitor ref. 6551 (Height x Width x Depth.): 186 x 198 x 46 mm SURFACE MONITOR MEASUREMENTS Measurements in mm. SMILE 7” Monitor 172 172 SMILE 3.5” Monitor 103 20 Note: Does not require a decorative frame. See installation.
SMILE SMILE VDS VDS INSTALLING THE BUILT-IN MONITOR 0m t 1.6 fee 5 5.2 3,5" 1 3 2 4 5 SMILE 3.
SMILE SMILE VDS VDS Page 6 0m t 1.6 fee 5 2 5.
SMILE SMILE VDS VDS INSTALLING THE SURFACE MONITOR SMILE 3.5” Monitor 2 3,5" 1 0m t 1.6 fee 5 5.2 4 3 SMILE 7” Monitor 7" 2 4 3 0m t 1.6 fee 5 5.
SMILE SMILE VDS VDS Connection • Video terminals: • Connection Terminals: V: live M: mesh CT: camera Activation (12 Vdc). V AUX : auxiliary video input (CCTV camera connection). Monitor Connector +, -: 18 Vdc power supply. L: data bus. F1, F2: additional functions. See programming chapter. T, -: call button connection for residential door (P1) +A, -: call extension connection ref. 2040, light and bell activator ref. 2438, etc... REF.
SMILE SMILE VDS VDS REF.2448 M VAUX V M M V F1 F2 CT+A T L - + M VAUX V M M V F1 F2 CT+A T L - + + 75 Ohm L P1 M VAUX V M M V 1 5 (-) V M V M COAX R1 +184 2 6 3 VMVM 75 P1 F1 F2 CT+A T L - + 75 Ohm REF.
SMILE SMILE VDS VDS REF.2448 M VAUX V M M V F1 F2 CT+A T L - + M VAUX V M M V F1 F2 CT+A T L - + 75 Ohm - P1 P1 + MV R DISTRIBUIDOR VIDEO 2 SALIDAS 2 OUTPUTS VIDEO DISTRIBUTOR + 1 5 (-) V MV M R1 +184 2 6 3 VMVM 75 L Auxiliary video input M VAUX V M M V COAX F1 F2 CT+A T L - + 75 Ohm P1 Available functions The functions available on the Smile VDS Basic Monitor are summarised in the following list: - It has capacitive buttons. - Open door. - Call to guard.
SMILE SMILE VDS VDS SMILE MONITOR menu. wildcard audio lockreleases Buttons Audio and Hang-up Activation Button · On receiving a call (the user has 30" seconds to answer before returning to standby. During this time the blue led audio button will blink to report a pending call to answer), press this button to talk to the guest.
SMILE SMILE VDS VDS - There is a function configured by the installer to activate the audio channel automatically upon receiving the call. See chapter b) Configuring conversation mode. In this mode the conversation will finish as usual by pressing the AUDIO button or after 90’’. Wildcard button: Auto-Start / Main-Secondary Camera Selection. · With the monitor on standby, press and hold the wildcard for 1 second to switch the monitor on manually. To activate the audio, press the audio activation button .
SMILE SMILE VDS VDS Lock Release / Call Guard Unit Button. · Pressing this button whilst communicating with the Entry Panel will activate the lock release. Note: The icon will indicate the channel activated at each moment (upper right corner of the monitor). 1 · Pressing this button whilst the monitor is on standby will result in a call being made to the guard unit (where one exists). Note: If the channel is busy an error tone "BEEP" will be generated and the call to the guard will not be made.
SMILE SMILE VDS VDS PROGRAMMING THE SMILE MONITOR The monitor will not function until it has been programmed! There are two monitor programming options: Option 1: from Panel + Monitor Option 2: from the Monitor. Notes: - The wildcard button blinking (red) indicates that the monitor has not been programmed.
SMILE SMILE VDS VDS 4. The selected option is displayed on the white line under the icon. Press , and a screen appears confirming the selected option: programming from the panel and you hear a beep on the monitor. ___ ___ 2222 4444 5. The monitor automatically connects to the street panel, activating the camera (this shows a panel icon in the upper left corner of the monitor). Enter the calling code for this monitor from the panel.
SMILE SMILE VDS VDS Notice: - The wildcard button will continue blinking (red) until having exited programming. 6. Exit Programming: When you press you exit to the previous programming menu. Continue pressing until you exit programming. The monitor will also automatically exit programming mode after 60 seconds of inactivity. Note: - Upon exiting programming, the wildcard button stops blinking, indicating that the monitor is programmed.
SMILE SMILE VDS VDS - : Decrease button selected with the cursor. + : Increase button selected with the cursor. : This moves to the following digit. : It restarts with the first digit. 028 ___ 028 2222 4444 5. Exit Programming: When you press you exit to the previous programming menu. Continue pressing until you exit programming. The monitor will also automatically exit programming mode after 60 seconds of inactivity.
SMILE SMILE VDS VDS To access the ADMINISTRATOR menu 2. Enter the administrator code, which by default is 4444 (it may be changed). The first number is blinking, each time you press + or - it increases or decreases this number. When the administrator code has been entered you access the configuration menu screen appears. 0000 - : Decrease button selected with the cursor. + : Increase button selected with the cursor. : This moves to the next digit and replaces the previous one with *.
SMILE SMILE VDS VDS a3 ___ a5 2222 a.1) Programming the monitor from the monitor itself. Explained in previous pages, see "Programming the smile monitor", option 1. a6 4444 a.2) Programming the monitor from the panel. a1 028 a2 a4 Explained in previous pages, see "Programming the smile monitor," option 2. Call forward. There is the option to configure the call forward to another residence, in order to be able to attend to the call from another location.
SMILE SMILE VDS VDS 028 071 071 2222 4444 3rd. Exit Programming: When you press you exit to the previous programming menu. Continue pressing until you exit programming. The monitor will also automatically exit programming mode after 60 seconds of inactivity. a.4) Programming a call forward. Option 2: from Panel + Monitor 028 ___ 1. In order to select programming from the panel, select the panel from the VDS (2) line with the right arrow. 2222 4444 2.
SMILE SMILE VDS VDS Notes: - The time between steps 4 and 5 must be less than 2 and half minutes. - Programming is always done from the panel activated as the main panel. Panel icon 1 A different calling tone is produced, confirming the monitor´s programming, continuing to view the camera´s image and after a few seconds the monitor returns to the programming screen. 028 1 071 2222 4444 4. Exit Programming: When you press you exit to the previous programming menu.
SMILE SMILE VDS VDS x x M x x x x M x x M 1. In order to enable the call forward option, 2. Pressing , select the desired access go to the corresponding icon with the mode, in this case the menu M has been cursors. selected. The selected option is displayed with the white line blinking under the icon. x x M x x M 3. Pressing , select the desired access 4. Press , to exit to the previous menu. mode, in the selected option.
SMILE SMILE VDS VDS 1. In order to enable the call forward option, 2. By pressing , you select the call forward, and confirm the selection, since it is go to the corresponding icon with the indicated by the white point on the screen cursors, (white line under the icon). next to the call forward icon. In order to remove the selection re-press .
SMILE SMILE VDS VDS 0000 2. Enter the administrator code you wish to change. The first number is blinking, each time you press + or - it increases or decreases this number. When the administrator code has been entered you access the configuration menu screen appears. - : Decrease button selected with the cursor. + : Increase button selected with the cursor. : This moves to the next digit and replaces the previous one with *. : It restarts with the first digit.
SMILE SMILE VDS VDS 3. With the cursors, select the icon of the desired conversation mode. Press , to select the conversation mode. On the selected mode you will see a. the option to automatically open audio after receiving a call simplex hands free 4. For example, if you select simplex mode with automatic audio connection upon receiving the call. With this option selected with the cursors (white line under the cursor), press , if you want to remove the selection, you also press .
SMILE SMILE VDS VDS x x M x x 2. By default the functions are enabled as the screen shows. The functions that appear with: - x: are enabled with a shortcut button and also appear in the menu. - : is enabled as a wildcard and also appears in the menu. . - M: are enabled for the menu. Notes: - The default functions assigned to shortcut buttons are: o F1 o F2 o Do not disturb mode. o Auto-start. - A short press on the menu button , shows the corresponding icons to these selected shortcut buttons.
SMILE SMILE VDS VDS x x M x x x M x x M x 4. In order to configure the function´s access mode, go to the corresponding icon with the cursors, (white line under the icon). Pressing , you select the desired access mode, in this case the menu M has been selected. While selecting the option, the white line is blinking under the icon. M 5. Pressing , select the desired access 6. Press , to exit to the previous menu. mode, in the selected option.
SMILE SMILE VDS VDS 9. These are the default programmed functions in the monitor as shortcuts and that therefore appear as both shortcuts and in the menu. x x M x x For Shortcut buttons. Via the MENU. (Pressing "Menu" for 3 seconds. ). (Short press "Menu" ). Description of the functions e1) Do not disturb mode (cancel ringtone) Function fordeactivating the ringtone.
SMILE SMILE VDS VDS 03:15 3. For example, we enter 03:15, so the function will be activated for 3 hours and 15 minutes. Going to the previous screen you will view the red led bell, indicating that the function is activated. 4. Having selected the do not disturb mode by pressing , we disable the selection (the red led bell disappears). In order to re-select them we must start the process form the 1st point. Do not disturb mode activated __:__ 5.
SMILE SMILE VDS VDS Just as previously stated, we exit the do not disturb mode: - When the programmed time has passed. - by pressing the shortcut button or - by selecting the do not disturb icon on the menu. Notice: - We can configure the call extension, light and ringtone activator...etc, for this to be enabled in this mode when the monitor receives a call. For this we must activate within the Parameters in Activate auxiliary devices, see the corresponding chapter f) Parameters.
SMILE SMILE VDS VDS For example, Call the Guard Unit as a shortcut button (x). This function is enabled as a shortcut button and also appears in the menu. Via the MENU. (Pressing "Menu" for 3 seconds. x x M x x For Shortcut buttons. ). (Short press "Menu" ). e4) Auto-start With the monitor on standby, press and hold the wildcard for 1 second to switch the monitor on manually.
SMILE SMILE VDS VDS The auto-start function is enabled as a shortcut button and also appears in the menu. x M x x For Shortcut buttons. Via the MENU. (Pressing "Menu" for 3 seconds. x (Short press "Menu" ). ). e6) Auxiliary function F1 The function F1 and F1 terminal have the option of being configured. You can select between Sending a negative (output) and Panic call to the MDS Guard Unit (input). It is initially configured, by default, as an output and sends a negative.
SMILE SMILE VDS VDS The F1 terminal acts as an input connecting a button on it for the Panic call to the MDS Guard Unit function (input). In combination with a MDS/VDS decoder version V10.26 or above, you can make a panic call to the MDS guard unit. When you press the button "Panic Alarm" button, the corresponding command is sent through the bus.
SMILE SMILE VDS VDS e7) Auxiliary function F2 The F2 function mainly acts as an output and sends a negative. This output remains active while pressing the button. The screen notifies of the action: F2 OK. The function is enabled as a shortcut button and also appears in the menu. via the menu shortcut buttons This output remains active while pressing the button. The F2 terminal can also be configured, giving a negative when the lock-release command is sent, during a call or conversation.
SMILE SMILE VDS VDS e8) Auxiliary video input (CCTV) There is the option to connect an external analogic camera to the monitor and use it as a CCTV image. This camera´s image appears on the monitor when we select the CCTV option on the Menu. For example, CCTV as a shortcut button (x). This function is enabled as a shortcut button and also appears in the menu. x x M M x x With Shortcut buttons. Via the MENU. (Pressing "Menu" for 3 seconds. x ). (Short press "Menu" ).
SMILE SMILE VDS VDS Notes: - If you have a motion detector, this can be connected to the doorbell so that anytime the camera detects a person it generates a ringtone and activates the video. - We suggest deactivating the Auxiliary video with door bell function during long absences (vacations), in order to avoid the monitor screen permanently remaining on when a call is made from the panel.
SMILE SMILE VDS VDS When you press the relevant button from the monitor: Lift Control, the corresponding command is transmitted by the bus, and it appears on the monitor. e11) Messages - e12) Automatisation- e13) Alarms These options are not available in the basic model. e13) Call forward There is the option to connect the call forward to another residence, in order to be able to attend to the call from another location. It must be pre-enabled by the installer and selected by the user.
SMILE SMILE VDS VDS f1) Activation F2 with door opening The F2 terminal can also be configured, giving a negative when the lock-release command is sent, while the lock-release button is down, during a call or conversation. See Details: e5) Auxiliary function F2. f2) Display call origin. By default this option is activated, displaying the call origin on the monitor´s screen. panel icon indicating the panel number 1 f3) Induction ear loop This function is not available in the basic model.
SMILE SMILE VDS VDS Notes: - If you have a motion detector, this can be connected to the doorbell so that anytime the camera detects a person it generates a ringtone and activates the video. - We suggest deactivating the Auxiliary video with door bell function during long absences (vacations), in order to avoid the monitor screen permanently remaining on when a call is made from the panel. f5) Activate auxiliary devices The following may be configured: call extension, light and ringtone activator...
SMILE SMILE VDS VDS 1. Select the default parameters option via the cursors (white line under the icon) and press. The monitor exits the menu and starts to save the selected option. This status is displayed, since it sequentially goes through all capacitive buttons, indicating that the reset is being performed. 2. When all capacitive buttons have been lit, this option is saved.
SMILE SMILE VDS VDS 2. When all capacitive buttons have been lit, this option is saved. Since it deletes the programmed monitor´s address, the wildcard button blinks red, indicating that the monitor is not programmed. ADJUSTMENTS: Video and Audio Video adjustments: Brightness - Contrast - Colour The monitor allows you to adjust brightness, contrast and colour while you have received a call or performed an auto-start. Short-press the "MENU" button on the screen to adjust the image´s brightness.
SMILE SMILE VDS VDS 2. Select the desired option and increase or decrease the video adjustments according to the selected option. 1 1 1 contrast brightness colour - : Button to decrease. + : Button to increase. : Return to the previous screen and confirm the selection..
SMILE SMILE VDS VDS Audio Adjustments While the audio channel is open the audio´s volume can be regulated via a contextual menu on the screen. Short-press the "MENU" button screen to adjust the audio. and a menu appears on the 1. Select the audio adjustments option with the corresponding capacitive button. 1 adjustments audio mute function: activate/deactivate the corresponding capacitive button. Mute function. When activated, the icon will disappear from the upper right of the screen. 2.
SMILE SMILE VDS VDS PROGRAMMING: USER Menu Access the user menu Notice: - Navigation buttons and capacitive buttons navigation buttons The icons viewed on the screen (navigation buttons: , , and ), are managed with the corresponding capacitive buttons located on the monitor capacitive buttons : Return to the previous screen or stand-by. : Select the previous menu option. : Mark the following menu option. : Confirm the selection and activate the function. 1. To access the USER menu.
SMILE SMILE VDS VDS a) Ringtones Within the menu, the monitor allows you to select an independent ringtone for the call from: - a1) Main street panel - a2) Secondary street panel - a3) Doorbell You can select that the ringtone rings three times (continuous mode). We can also adjust the volume. a1 1 1 a2 1 1 a3 1 1 1. Select the origin of the call with the cursors 2. Within the ringtone (white line under the , (panel 1, panel 2 or door bell).
SMILE SMILE VDS VDS 2 1 5. Having selected continuous mode, Press, to select it. In order to remove the selection you also press . To go to the next options press . 1 continuos mode is selected: the ringtone is placed 3 times Audio Adjustments To regulate the volume. 1. Select the audio adjustments option via the cursors(white line under the icon) and press . The following screen appears: 2. While in audio adjustments, use the capacitive buttons to obtain the desired settings.
SMILE SMILE VDS VDS b) Configuring alarms This function is not available in the basic model. c) Date and Time This function is not available in the basic model. d) Administrator Menu Menu for the installer to configure the monitor according the the installation´s needs. Description of functions 1. Do not disturb mode (cancel the ringtone) Within the user menu, you can select the Do Not Disturb mode. Function for deactivating the ringtone.
SMILE SMILE VDS VDS The same operation can also be performed via the menu´s icon. Via the MENU. (Pressing "Menu" for 3 seconds. __:__ ). If you want to select this mode indefinitely (- - : - -), upon entering in this screen the first number is blinking, press + until you view the cursor - , press , the remaining digits automatically turn into cursors (- - : - -), therefore the indefinite mode is on. Continue pressing , until you reach the desired menu or you exit programming.
SMILE SMILE VDS VDS SMILE MONITOR menu. wildcard audio lockreleases Buttons Audio and Hang-up Activation Button. · Upon receiving a call (the user has 30" seconds to answer before returning to standby. During this time the blue led audio button will blink to report a pending call to answer), press this button to talk to the visitor.
SMILE SMILE VDS VDS - There is a function configured by the installer to activate the audio channel automatically upon receiving the call. In this mode the conversation will finish as usual by pressing the AUDIO button or after 90’’. Notice: - Function assigned by the installer. Consult the installer. Wildcard button: Auto-Start / Main-Secondary Camera Selection. · With the monitor on standby, press and hold the wildcard for 1 second to switch the monitor on manually.
SMILE SMILE VDS VDS Lock Releases / Call Guard Unit Button. · Pressing this button whilst communicating with the Entry Panel will activate the lock release. Note: The icon will indicate the channel activated at each moment (upper right corner of the monitor). 1 · Pressing this button whilst the monitor is on standby will result in a call being made to the guard unit (where one exists). Note: If the channel is busy an error tone "BEEP" will be generated and the call to the guard will not be made.
SMILE SMILE VDS VDS Answering a call: "Handsfree" Mode: 1 When the call button on the Entry Panel is pressed a call tone is produced both on the panel and on the monitor, causing the screen to start up. Press the button to speak with the visitor. The audio channel between the street and the home will be opened; operating in hands-free mode. The communication will automatically end after 90 seconds, or at any time by pressing the button .
SMILE SMILE VDS VDS Manual Monitor Activation (Auto-Start) With the monitor on standby, press and hold the wildcard for 1 second to switch the monitor on manually. To sequentially select between the main camera and the secondary camera (where one exists), for 2 seconds. press and hold the wildcard button To activate the audio and speak to the visitor or open the door, follow the steps above. If communication is not established with the entry panel, the monitor will automatically switch off after 30 seconds.