Manual

ManualsBrandsFesto ManualsEquipmentКонтроллер крайних положений SPC11

Supplementary

manu al

Drive-specific

supplement for

operating the

SPC11withstan-

dard cylinder type

DNC-...

Manual

196 736

en 0012NH

[647 470]

SPC11 Soft Stop

Summary of content (64 pages)

PAGE 1
SPC11 Soft Stop Supplementary manual Drive-specific supplement for operating the SPC11 with standard cylinder type DNC-...
PAGE 2
PAGE 3
Contents and general instructions Author . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S. Breuer Editors . . . . . . . . . . . . . . . . . . . . . . . . H.-J. Drung, M. Holder Original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . de Translation . . . . . . . . . . . . . . . . . . . . . transline Deutschland Layout . . . . . . . . . . . . . . . . . . . Festo AG & Co., Dept. KG-GD Type setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
Contents and general instructions Trade marks Temposonics® II is a registered trade mark of MTS Sensortechnologie GmbH & Co Festo P.
PAGE 5
Contents and general instructions Contents Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important user instructions . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
Contents and general instructions DNC-32-80 to ...-32-140 in horizontal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DNC-32-141 to ...-32-290 in horizontal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DNC-32-291 to ...-32-590 in horizontal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DNC-32-591 to ...-32-735 in horizontal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DNC-40-80 to ...
PAGE 7
Contents and general instructions Festo P.
PAGE 8
Contents and general instructions Intended use The SPC11 has been designed for fitting into a machine or an automation device. In conjunction with permitted drives and measuring systems and a proportional directional control valve type MPYE-5-..., the SPC11 enables: – fast movement into the mechanical end positions and one or two selectable mid-positions – manual movement between the end positions. Depending on the drive used, fixed stops are in some cases required for protecting the drive.
PAGE 9
Contents and general instructions Service If you have any technical problems, please contact your local Festo Service. Target group This manual is intended exclusively for personnel trained in control and automation technology. Festo P.
PAGE 10
Contents and general instructions Important user instructions Danger categories This manual contains instructions on the possible dangers which may occur if the product is not used correctly. These instructions are marked (Warning, Caution, etc), printed on a shaded background and marked additionally with a pictogram. A distinction is made between the following danger warnings: Warning This means that failure to observe this instruction may result in serious personal injury or damage to property.
PAGE 11
Contents and general instructions Marking special information The following pictograms mark passages in the text containing special information. Pictograms Information: Recommendations, tips and references to other sources of information. Accessories: Information on necessary or sensible accessories for the Festo product. Environment: Information on environment-friendly use of Festo products. Text markings S The bullet indicates activities which may be carried out in any order. 2.
PAGE 12
Contents and general instructions Product-specific terms and abbreviations The following product-specific abbreviations are used in this manual: Term/ abbreviation Meaning 0-signal Input or output supplies 0 V 1-signal Input or output supplies 24 V Drive In this manual the term ”Drive” represents the terms ”linear unit” (DGP(I)(L)-...), ”cylinder” (DNC-...) or ”rotary drive” (DSMI).
PAGE 13
Contents and general instructions Notes on the use of this manual This manual contains special information on installing and commissioning the SPC11 in conjunction with drive type DNC-... . General, basic information on the method of operation, on fitting, installing and commissioning pneumatic drives with the SPC11 can be found in the System manual P.BE-SPC11-SYS-... . Manuals for the SPC11 Manual Title Contents System manual SPC11 Soft Stop electronics/ pneumatics P.BE-SPC11-SYS...
PAGE 14
Contents and general instructions XII Festo P.
PAGE 15
Summary of components Chapter 1 Festo P.
PAGE 16
1. Summary of components Contents 1. Summary of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 1.2 1.3 General instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System structure with the DNC-... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notes on installing the pneumatic components . . . . . . . . . . . . . . . . . . . . . . . 1-3 1-4 1-5 1-2 Festo P.
PAGE 17
1. Summary of components 1.1 General instructions Warning Faults in the system structure as well as incorrectly set parameters can cause the piston to move uncushioned into one of the end positions. This may cause damage to the fixed stop or to the drive. Please observe the following instructions in order to prevent such collisions. Festo P.BE-SPC11-DNC-EN en 0012NH S Set up the system with the greatest care.
PAGE 18
1. Summary of components 1.2 System structure with the DNC-... The following diagram shows the basic structure of a drive with the SPC11 and standard cylinder type DNC-... . 2 3 4 5 6 1 aJ 9 8 7 1 Guide 6 SPC11-POT-LWG-... 2 Coupling 7 Proportional directional control valve 3 Measuring system (here type MLO-POT-...-LWG) 4 Drive (here type DNC-...) 5 Earth strip type MPYE-5-...
PAGE 19
1. Summary of components 1.3 Notes on installing the pneumatic components Caution If the power supply is switched off when the compressed air supply is still switched on, undesired movements of the connected actuators may be triggered, thereby causing damage. Always switch off the power supply and the compressed air supply simultaneously or in the following sequence: 1. The compressed air supply 2.
PAGE 20
1. Summary of components 1 2 3 4 5 6 aJ 9 7 8 1 ... aJ Notes on installation see following pages Fig. 1/2: Summary of pneumatic installation Compressed air supply ( 1 ) see System manual type P.BE-SPC11-SYS... Service unit ( 2 ) see System manual type P.BE-SPC11-SYS... Compressed air reservoir ( 3 ) see System manual type P.BE-SPC11-SYS... 1-6 Festo P.
PAGE 21
1. Summary of components Compressed air tubing and screw connectors ( 4 ) see System manual type P.BE-SPC11-SYS... Festo P.BE-SPC11-DNC-EN en 0012NH S Lay the tubing between valve (MPYE-5-...) and drive (DNC-...) symmetrically. Recommendation: Tubing length = cylinder stroke length + 50 mm S Use sizes for the compressed air tubing and tube connectors in accordance with the following table.
PAGE 22
1. Summary of components Horizontal fitting position Stroke length i mm in Valve type MPYE-... Screw connectors for Tube type PUN MPYE-... DNC-... DNC-32-... 80...440 MPYE-5-1/8-LF-010B QS-1/8-8 QS-1/8-8 PUN-8x1,25 441...735 MPYE-5-1/8-HF-010B QS-1/8-8 QS-1/8-8 PUN-8x1,25 80...290 MPYE-5-1/8-LF-010B QS-1/8-8 QS-1/4-8 PUN-8x1,25 291...440 MPYE-5-1/8-HF-010B QS-1/8-8 QS-1/4-8 PUN-8x1,25 441...735 MPYE-5-1/4-010B QS-1/4-10 QS-1/4-10 PUN-10x1,25 80...
PAGE 23
1. Summary of components Horizontal fitting position 176...440 MPYE-5-1/4-010B QS-1/4-10 QS-3/8-10 PUN-10x1,5 441...735 MPYE-5-3/8-010B QS-3/8-12 QS-3/8-12 PUN-12x2 Proportional directional control valve ( 5 ) see System manual type P.BE-SPC11-SYS... Work connection 2 of the proportional directional control valve must be connected with tubing to the cylinder connection on the same side as the electrical connection for the potentiometer. 1 4 2 1 1 Electrical connection Fig.
PAGE 24
1. Summary of components Standard cylinder type DNC-... ( 6 ) Please note The following DNC variants are not permitted for use the with the SPC11: – constant-run variant S10 (slow speed) – light-run variant S11 (low friction) – temperature-resistant variant S6 (only on request). Use only: 1-10 – DNC drives with max. permitted piston speed Vmax > 1 m/s. – Permitted combinations of drives, valves and measuring systems, cylinder diameter, cylinder length and mass loads see “Parameters for the DNC-...
PAGE 25
1. Summary of components Measuring system type MLO-POT-...-LWG ( 7 ) S Use measuring system type MLO-POT-...-LWG (piston-rod potentiometer) with the DNC-... . The measuring system must be longer than the cylinder stroke used. There must be an electric reserve. The following stroke lengths are possible, depending on the measuring system length: Measuring system length Max.
PAGE 26
1. Summary of components Please note If the measuring system sags or shakes when operating, you must provide additional support. Use suitable measures to cushion vibration. Coupling ( 8 ) If a coupling is required between the piston rod and the guide: S Check the play of the coupling. The following applies here: coupling play ≤ 0.05 mm S If necessary, adjust the play of the coupling accordingly.
PAGE 27
1. Summary of components Fixed stops ( 9 ) Caution Use of the complete drive length can cause faults. Set the fixed stops so that the distance to the end position of the drive is at least 0.5 mm. External fixed stops are required for operating the DNC-... in conjunction with the SPC11. The end positions can be set as desired with the fixed stops. The cushioning path of the internal end position cushioning should not project into the work stroke used.
PAGE 28
1. Summary of components Mass load ( 9 ) Fit the mass load free of play. Possible moveable mass loads see “DIL switch settings for the DNC-...” in chapter 2. The tables listed there contain all the permitted combinations of drives, valves and mass loads for operation with the SPC11 type SPC11-POT-LWG-... . 1-14 Festo P.
PAGE 29
Parameters of the SPC11 for the DNC-... Chapter 2 Festo P.
PAGE 30
2. Parameters of the SPC11 for the DNC-... Contents 2. Parameters of the SPC11 for the DNC-... . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2.1 2.2 2.3 Parameters of the SPC11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting the parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parameters for the DNC-...-... in horizontal operation . . . . . . . . . . . . . . . . . . DNC-32-80 to ...
PAGE 31
2. Parameters of the SPC11 for the DNC-... 2.1 Parameters of the SPC11 Warning Incorrectly set parameters can cause damage to the fixed stops and to the drive. Take the utmost care when setting the parameters. Certain conditions of use must be made known to the SPC11.
PAGE 32
2. Parameters of the SPC11 for the DNC-... Specifications for setting the parameters In order to set the parameters, you will require the following specifications: – Cylinder stroke length (see type plate for drive used). – Valve type (see type plate for proportional directional control valve used). – Maximum mass load with which the drive is loaded. Mass load If you wish to position with different masses: 2-4 – Positioning with a mass up to 30 % less does not usually present any problems.
PAGE 33
2. Parameters of the SPC11 for the DNC-... 2.2 Setting the parameters Warning Incorrectly set parameters can cause damage to the fixed stops and to the drive. Always set the amplification and cushioning stages for the maximum mass load used. If in doubt, set first the amplification and cushioning stages for the larger mass load. The specified positioning times as well as optimum system behaviour specified in section 2.
PAGE 34
2. Parameters of the SPC11 for the DNC-... The average positioning times specified apply only to drives with standard stroke length 2. Measuring system and valve types as well as the specified parameters (amplification stage, cushioning stage and system parameter) are also valid for drives with X-stroke length 1. Optimization of the positioning behaviour may be necessary in individual cases (see System manual). DNC-32-80 to ...-32-115 2 3 MPYE-5-1/8-LF-010B 3 0 9 30 0.38 4 12 61 0.
PAGE 35
2. Parameters of the SPC11 for the DNC-... The parameters listed in the following tables are adapted exactly to the specified combinations of valves, drives, mass loads and fitting positions. Please note Faultless operation can only be guaranteed if all components are fitted correctly. S Use only the specified combinations of valve, drive and mass load. S Observe the installation instructions in chapter 1 as well as in the system manual.
PAGE 36
2. Parameters of the SPC11 for the DNC-... DNC-32-80 to ...-32-140 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-LF-010B 9 30 0.38 4 12 61 0.44 5 11 31 0.42 6 3 14 30 0.41 7 14 61 0.42 8 15 31 0.50 9 5 16 30 0.44 9 16 61 0.45 9 17 31 0.46 12 6 17 30 0.46 10 19 61 0.45 11 19 31 0.50 15 7 18 30 0.44 11 23 61 0.52 12 20 31 0.50 18 8 20 30 0.51 12 21 61 0.8 12 22 31 0.50 21 9 21 30 0.45 13 21 61 0.45 13 22 31 0.
PAGE 37
2. Parameters of the SPC11 for the DNC-... DNC-32-141 to ...-32-290 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-LF-010B 12 63 0.45 10 13 33 0.49 13 13 44 0.52 6 12 15 63 0.45 12 16 33 0.53 15 17 44 0.53 9 14 17 63 0.48 14 19 33 0.58 17 19 44 0.54 12 15 20 63 0.52 15 22 33 0.60 18 22 44 0.58 15 16 21 63 0.51 16 22 33 0.63 19 23 44 0.67 18 16 23 63 0.58 17 24 33 0.65 20 24 44 0.65 21 17 23 63 0.53 18 24 33 0.
PAGE 38
2. Parameters of the SPC11 for the DNC-... DNC-32-291 to ...-32-590 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-HF-010B 14 44 0.61 17 15 45 0.69 16 17 54 0.58 6 18 18 44 0.62 20 19 45 0.67 19 20 54 0.62 9 19 20 44 0.70 22 22 45 0.70 21 23 54 0.64 12 21 22 44 0.65 23 24 45 0.74 22 24 54 0.66 15 21 24 44 0.80 24 25 45 0.75 23 26 54 0.70 18 22 26 44 0.71 25 26 45 0.82 23 27 54 0.72 21 23 26 44 0.75 25 28 45 0.
PAGE 39
2. Parameters of the SPC11 for the DNC-... DNC-32-591 to ...-32-735 in horizontal operation DNC-32-650 591...735 mm MLO-POT-750-LWG 55 0.74 9 23 24 55 0.75 12 24 26 55 0.75 15 25 27 55 0.80 18 26 28 55 0.76 21 27 28 55 0.81 24 27 30 55 0.87 27 28 29 55 0.83 30 28 30 55 0.84 33 29 30 55 0.85 36 29 32 55 0.88 39 29 32 55 0.87 42 30 31 55 0.90 45 30 32 55 0.92 Festo P.
PAGE 40
2. Parameters of the SPC11 for the DNC-... DNC-40-80 to ...-40-140 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-LF-010B 9 41 0.49 7 10 73 0.49 8 10 43 0.48 10 6 13 41 0.44 10 14 73 0.49 10 15 43 0.56 15 8 17 41 0.52 12 17 73 0.52 12 17 43 0.55 20 9 18 41 0.50 13 19 73 0.53 13 19 43 0.55 25 10 19 41 0.49 14 19 73 0.50 14 21 43 0.63 30 11 19 41 0.49 15 20 73 0.52 15 22 43 0.58 35 11 22 41 0.58 15 22 73 0.
PAGE 41
2. Parameters of the SPC11 for the DNC-... DNC-40-141 to ...-40-290 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-LF-010B 11 74 0.59 12 12 44 0.62 15 13 55 0.66 10 15 16 74 0.59 15 17 44 0.67 18 17 55 0.69 15 16 18 74 0.60 17 18 44 0.65 20 19 55 0.67 20 17 20 74 0.62 18 20 44 0.65 21 21 55 0.68 25 18 21 74 0.58 19 22 44 0.71 22 23 55 0.73 30 19 22 74 0.62 20 24 44 0.71 23 24 55 0.75 35 20 23 74 0.66 20 24 44 0.
PAGE 42
2. Parameters of the SPC11 for the DNC-... DNC-40-291 to ...-40-590 in horizontal operation MPYE-5-1/8-HF-010B MPYE-5-1/4-010B 15 43 0.56 16 16 44 0.63 16 18 53 0.54 10 16 19 43 0.59 19 19 44 0.64 17 21 53 0.62 15 18 21 43 0.65 20 22 44 0.65 19 24 53 0.62 20 19 22 43 0.61 21 24 44 0.76 20 26 53 0.74 25 20 24 43 0.71 22 25 44 0.76 21 26 53 0.63 30 21 24 43 0.62 23 26 44 0.72 22 26 53 0.70 35 21 26 43 0.70 24 25 44 0.
PAGE 43
2. Parameters of the SPC11 for the DNC-... DNC-40-591 to ...-40-735 in horizontal operation DNC-40-650 591...735 mm MLO-POT-750-LWG 54 0.72 15 22 24 54 0.72 20 23 25 54 0.74 25 24 26 54 0.72 30 24 30 54 0.91 35 25 29 54 0.77 40 26 29 54 0.74 45 26 31 54 0.82 50 27 30 54 0.80 55 27 31 54 0.88 60 27 33 54 0.87 65 28 32 54 0.90 70 28 32 54 0.89 75 28 33 54 0.85 Festo P.
PAGE 44
2. Parameters of the SPC11 for the DNC-... DNC-50-80 to ...-50-140 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-LF-010B 7 43 0.50 10 9 74 0.55 10 9 44 0.59 16 8 13 43 0.53 12 13 74 0.56 13 14 44 0.63 24 10 16 43 0.54 14 17 74 0.58 15 17 44 0.60 32 11 19 43 0.60 15 18 74 0.57 16 19 44 0.61 40 12 20 43 0.56 16 19 74 0.59 17 20 44 0.65 48 13 21 43 0.59 17 20 74 0.58 18 21 44 0.62 56 14 21 43 0.59 18 21 74 0.
PAGE 45
2. Parameters of the SPC11 for the DNC-... DNC-50-141 to ...-50-290 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-LF-010B 10 76 0.69 15 11 46 0.75 18 12 57 0.82 16 17 16 76 0.65 18 16 46 0.73 21 17 57 0.81 24 19 18 76 0.69 19 19 46 0.78 22 20 57 0.83 32 20 19 76 0.64 21 20 46 0.76 24 21 57 0.76 40 21 20 76 0.63 21 22 46 0.78 25 22 57 0.81 48 22 22 76 0.67 22 23 46 0.82 25 23 57 0.85 56 22 23 76 0.74 23 23 46 0.
PAGE 46
2. Parameters of the SPC11 for the DNC-... DNC-50-291 to ...-50-590 in horizontal operation MPYE-5-1/8-HF-010B MPYE-5-1/4-010B 16 55 0.78 18 16 56 0.84 17 17 54 0.69 16 19 19 55 0.77 21 19 56 0.84 20 21 54 0.74 24 20 21 55 0.81 23 22 56 0.88 22 24 54 0.76 32 21 23 55 0.86 24 23 56 0.87 23 24 54 0.74 40 22 24 55 0.84 25 24 56 0.89 24 25 54 0.71 48 23 25 55 0.85 26 25 56 0.93 24 26 54 0.80 56 24 25 55 0.82 26 26 56 1.
PAGE 47
2. Parameters of the SPC11 for the DNC-... DNC-50-591 to ...-50-735 in horizontal operation DNC-50-650 591...735 mm MLO-POT-750-LWG 54 0.95 24 22 25 54 0.87 32 23 26 54 0.89 40 24 28 54 0.99 48 25 29 54 0.93 56 25 29 54 0.92 64 26 30 54 0.95 72 26 31 54 0.96 80 27 31 54 0.93 88 27 33 54 1.05 96 28 33 54 1.08 104 28 33 54 0.96 112 28 35 54 1.11 120 29 34 54 1.03 Festo P.
PAGE 48
2. Parameters of the SPC11 for the DNC-... DNC-63-80 to ...-63-140 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-LF-010B 4 55 0.61 12 6 86 0.70 12 8 56 0.75 24 11 11 55 0.56 15 13 86 0.67 15 14 56 0.76 36 12 16 55 0.71 16 17 86 0.73 17 18 56 0.75 48 14 17 55 0.66 18 18 86 0.73 18 20 56 0.83 60 15 18 55 0.61 19 19 86 0.72 19 20 56 0.80 72 15 19 55 0.63 19 20 86 0.69 20 20 56 0.71 84 16 20 55 0.64 20 21 86 0.
PAGE 49
2. Parameters of the SPC11 for the DNC-... DNC-63-141 to ...-63-290 in horizontal operation MPYE-5-1/8-HF-010B MPYE-5-1/8-HF-010B 9 78 0.77 13 13 45 0.65 16 13 66 0.87 24 19 15 78 0.80 16 16 45 0.65 19 19 66 0.88 36 21 17 78 0.77 17 19 45 0.73 20 23 66 0.92 48 22 19 78 0.82 18 20 45 0.69 21 24 66 0.94 60 23 20 78 0.75 19 21 45 0.72 22 24 66 0.99 72 24 21 78 0.76 20 21 45 0.72 23 24 66 0.90 84 25 22 78 0.79 21 23 45 0.
PAGE 50
2. Parameters of the SPC11 for the DNC-... DNC-63-291 to ...-63-590 in horizontal operation MPYE-5-1/4-010B MPYE-5-1/4-010B 14 57 0.95 16 16 55 0.84 19 17 66 0.89 24 21 19 57 0.97 19 20 55 0.86 22 21 66 0.92 36 22 20 57 0.95 21 21 55 0.80 24 23 66 0.90 48 24 22 57 1.00 22 23 55 0.87 25 24 66 0.95 60 25 23 57 0.95 23 24 55 0.85 26 25 66 0.97 72 25 24 57 0.97 24 24 55 0.89 27 25 66 0.97 84 26 25 57 0.99 24 25 55 0.
PAGE 51
2. Parameters of the SPC11 for the DNC-... DNC-63-591 to ...-63-735 in horizontal operation DNC-63-650 591...735 mm MLO-POT-750-LWG 56 0.89 36 24 24 56 0.93 48 25 27 56 0.95 60 26 27 56 1.03 72 27 28 56 1.03 84 28 28 56 0.92 96 28 29 56 1.03 108 29 29 56 0.96 120 29 31 56 1.04 132 30 30 56 0.96 144 30 32 56 1.05 156 30 32 56 1.06 168 31 31 56 0.97 180 31 32 56 1.01 Festo P.
PAGE 52
2. Parameters of the SPC11 for the DNC-... DNC-80-80 to ...-80-140 in horizontal operation MPYE-5-1/8-LF-010B MPYE-5-1/8-HF-010B 2 56 0.77 15 3 88 0.83 11 8 55 0.66 40 14 13 56 0.78 17 15 88 0.82 14 14 55 0.69 60 15 17 56 0.84 19 18 88 0.85 15 19 55 0.73 80 16 19 56 0.85 20 19 88 0.85 17 19 55 0.70 100 17 20 56 0.79 21 20 88 0.84 18 19 55 0.70 120 18 20 56 0.76 22 21 88 0.82 18 20 55 0.69 140 19 20 56 0.74 23 22 88 0.
PAGE 53
2. Parameters of the SPC11 for the DNC-... DNC-80-141 to ...-80-290 in horizontal operation MPYE-5-1/4-010B MPYE-5-1/4-010B 12 77 0.76 11 14 44 0.69 14 14 65 0.91 40 18 16 77 0.80 14 18 44 0.65 17 19 65 0.86 60 19 18 77 0.79 16 18 44 0.68 19 23 65 0.88 80 21 19 77 0.76 17 20 44 0.67 20 24 65 0.91 100 22 21 77 0.79 18 21 44 0.72 21 24 65 0.83 120 22 22 77 0.78 19 22 44 0.72 22 24 65 0.84 140 23 22 77 0.78 19 23 44 0.
PAGE 54
2. Parameters of the SPC11 for the DNC-... DNC-80-291 to ...-80-590 in horizontal operation MPYE-5-1/4-010B MPYE-5-3/8-010B 16 56 0.94 19 17 57 1.06 20 17 67 0.99 40 19 20 56 0.99 22 20 57 1.04 23 20 67 1.02 60 21 21 56 0.93 23 22 57 1.03 24 23 67 1.02 80 22 22 56 0.91 25 23 57 1.04 25 26 67 1.11 100 23 24 56 1.00 26 24 57 1.08 26 26 67 1.07 120 24 25 56 0.99 26 25 57 1.06 27 28 67 1.12 140 25 25 56 0.92 27 26 57 1.
PAGE 55
2. Parameters of the SPC11 for the DNC-... DNC-80-591 to ...-80-735 in horizontal operation DNC-80-650 591...735 mm MLO-POT-750-LWG 57 1.22 60 27 24 57 1.18 80 28 26 57 1.23 100 29 28 57 1.22 120 30 29 57 1.33 140 30 31 57 1.29 160 31 30 57 1.29 180 32 30 57 1.28 200 32 30 57 1.27 220 32 31 57 1.31 240 33 32 57 1.28 260 33 32 57 1.33 280 33 32 57 1.31 300 34 32 57 1.29 Festo P.
PAGE 56
2. Parameters of the SPC11 for the DNC-... 2-28 Festo P.
PAGE 57
Technical appendix Appendix A Festo P.
PAGE 58
A. Technical appendix Contents A. Technical appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 A.1 A.2 Repetition accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3 A-5 A-2 Festo P.
PAGE 59
A. Technical appendix A.1 Repetition accuracy The repetition accuracy when moving to the mid-positions is ± 0.25 % of the rated length of the measuring system, but not more accurate than ± 2 mm. Please note Observe the instructions on repetition accuracy in the system manual in order to achieve good positioning behaviour and the specified repetition accuracy. Festo P.
PAGE 60
A. Technical appendix A-4 Festo P.
PAGE 61
A. Technical appendix A.2 Index Numbers 0-signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX 1-signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX A Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX Amplification stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX, 2-3 C Cushioning path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 62
A. Technical appendix M Manuals for the SPC11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X Drive-specific supplement . . . . . . . . . . . . . . . . . . . . . . . . . . X System manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X Mass load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 P Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 DNC-32-141 to ...-32-290 (horizontal) . . . . . . .
PAGE 63
A. Technical appendix S Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VI Setting Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Slide operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 System parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 T Teach procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX Text markings . . . . . . . . .
PAGE 64
A. Technical appendix A-8 Festo P.