User Manual

s = 8
Festool cutters
Groove dimensions (seal, width x depth)
1) Planet HS, 13.1 x 30
2) Schall-Ex L, 14.8 x 32 / Schall-Ex RD, 14.8 x 28
3) Draft excluders, 12 x 40 / Double seals, 12 x 40
4) Schall-Ex Ultra, 19.7 X 30
5) For box joints with Festool VS 600,
with extra precision across the diameter
ØD NL GL R Fα Order No.
s = 8
9 23 55 – – 490958
10 20 60 – – 490959
10 25 60 – – 490960
5)
10 30 60 – – 491648
11 20 60 – – 490961
12 20 60 – – 490962
12 30 60 – – 491649
13 20 60 – – 490963
14 20 60 – – 490964
15 20 60 – – 490965
16 20 60 – – 490966
16 30 65 – – 490967
18 20 60 – – 490968
18 30 65 – – 490969
19 20 60 – – 490970
20 20 60 – – 490971
20 30 65 – – 490972
22 20 60 – – 490973
24 20 60 – – 490974
25 20 60 – – 490975
30 20 60 – – 490976
s = 12
10 35 90 – – 491086
12 40 90 – – 491087
3)
13.2 35 85 – – 493789
1)
14 40 85 – – 491088
14 50 100 – – 491089
15 35 85 – – 493790
2)
16 45 90 – – 491090
16 60 100 – – 491091
18 45 90 – – 491092
20 45 90 – – 491093
4)
22 45 90 – – 491094
24 45 90 – – 491095
30 35 90 – – 491096
ØD NL GL R Fα Order No.
8 20 50 – – 491078
10 25 55 – – 491079
12 30 61 – – 491080
14 30 66 – – 492715
16 30 70 – – 492716
18 30 70 – – 492717
s = 12, extra long reversible blade cut-
ter for door hinges in block frame and
door leaves
16 50/60 110 – – 497454
KN, with direct bit holder suitable
for OF 2200
20 50/60 110 – – 497455
24 50/80 127 – – 497456
ØD NL GL R Fα Order No.
6 16 50 – – 490944
5)
8 19 50 – – 490945
10 30 60 – – 490946
5)
12 20 52 – – 490947
14 20 52 – – 490948
16 20 52 – – 490949
18 25 57 – – 490950
20 25 57 – – 490951
4 10 45 – – 490977
6 16 50 – – 490978
5)
8 25 55 – – 490979
10 30 60 – – 490980
5)
ØD NL GL R Fα Order No.
3 8 45 – – 490941
4 15 48 – – 490942
5 12 50 – – 490943
ØD NL GL R Fα Order No.
19 20 64 – 0° 491082
ØD NL GL R Fα Order No.
12.7 25 65 – 0° 491027
6)
19 25 – – 0° 491028
7)
ØD NL GL R Fα Order No.
11 9.5 55 – 60° 491003
11 9.5 55 – 60° 491002
ØD
1
ØD
2
T
1
NL GL Order No.
16.3 12.3 9.3 14 80 492713
20.3 12.3 9.3 14 80 492714
6) Ø D 12.7 = Ball bearing, bottom
7) Ø D 19 = Ball bearing, top
Groove cutter
with plunge point s = 8/s = 12
Solid carbide groove cutter
with plunge point s = 8
Single-edged revers-
ible blade groove cutter
with plunge point
s = 8/s = 12
Flush trim cutter
with ball bearing s = 8
Stepped cutter
s = 12
Keyhole cutter
s = 8
Script cutter
s = 8
Reversible blade
edge-trimming cutter
with ball bearing
s = 8
Spiral groove cutter
with plunge point s = 8
Single-edged groove cutter
with plunge point s = 8
ØD NL GL R Fα Order No.
3 6 45 – – 490952
4 10 45 – – 490953
5 12 45 – – 490954
6 14 55 – – 490955
7 17 55 – – 490956
8 20 55 – – 490957
8 30 60 – – 491647
ØD
1
ØD
2
NL
1
NL
2
Fα Order No.
10.5 6 9 5 – 491035
18
2011_GB_en_FB_Routing.indd 18 06.05.11 16:30