User Manual

, s = 8
, s = 12
www.festool.co.uk
14) For partially covered dovetail joint
15) For open dovetail joint
16) Without cutter spindle
Total length (mm)
Working length (mm)
Cutter diameter (mm)
Shank diameter (mm)
Chamfering angle (°)
Radius (mm)
Marking for minimum clamping length
n max. = Maximum routing speed
Packaging unit
Tungsten carbide
High performance, high speed steel
ØD NL GL R
1
R
2
Order No.
19 12.5 54 5 4 491032
ØD NL GL R Fα Order No.
34 32 62 – – 491034
ØD NL T GL Fα Order No.
40 4 12 46 – 496054
ØD B d R Fα Order No.
40 1.5 6 – – 491038
16)
40 1.8 6 – – 491039
16)
40 2 6 – – 491040
16)
40 2.5 6 – – 491056
16)
40 3 6 – – 491057
16)
40 3.5 6 – – 491058
16)
40 4 6 – – 491059
16)
40 5 6 – – 491060
16)
ØD B d GL Fα Order No.
16 – 6 58 – 491062
ØD B d GL Fα Order No.
16 – 6 58 – 491061
28 – 6 53 – 491557
ØD B T GL Fα Order No.
40 2.8 6 47.5 – 491063
ØD NL GL R Fα Order No.
64 27 67 – 45° 492709
ØD NL GL R
1
R
2
Order No.
42 13 50 6 12 491137
ØD NL GL R Fα Order No.
14 7 50 – 90° 490999
11 9.5 50 – 60° 490997
14 7 50 – 90° 490998
ØD NL GL R Fα Order No.
14.3 13.5 46 – 15° 490990
14.3 13.5 46 – 15° 490988
ØD NL GL R Fα Order No.
14.3 13.5 46 – 15° 490992
14)
16 13.5 46 – 15° 490993
20 17 49 – 15° 490996
14)
14.3 16 50 – 10° 491164
15)
20 26 58 – 10° 491165
15)
14.3 13.5 46 – 15° 490991
14)
20 17 49 – 15° 490995
14)
16 12 55 – 15° 491097
20 14 57 – 15° 491098
24 15 58 – 15° 491099
30 18 60 – 15° 491100
Handrail cutters
s = 8
Milling cutter
s = 8
Disk groove cutters
s = 8
Laminate cutter
s = 8
Cutter spindle
not shown s = 8
Cutter spindle
with ball bearing
not shown
s = 8
V-groove cutters
s = 8
Dovetail cutter with spur
s = 8
Handrail cutters
s = 8
Tongue and groove cutters
s = 8
Mitre tongue and
groove cutter
n max 22,000
s = 12
Dovetail cutter
s = 8/s = 12
21
2011_GB_en_FB_Routing.indd 21 06.05.11 16:30