User’s Guide www.fetco.com Models: CBS-2051e CBS-2052e CBS-2052e20 f f f NOTICE TO INSTALLER: Please leave this book with the machine. Table of Contents Contact Information ..................................................2 Description & Features .............................................2 Specifications............................................................2 Requirements........................................................2 Weights and Capacities ........................................
Contact Information Phone: (800) 338-2699 (US & Canada) (847) 719-3000 Fax: (847) 719-3001 FETCO® Food Equipment Technologies Company 600 Rose Road Lake Zurich • IL • 60047-0429 • USA Email: sales@fetco.com techsupport@fetco.com Internet: www.fetco.
Electrical Configuration and Brewing Efficiency US & Canada CBS-2051e Electrical Config. Code E51016 Heater Configuration Voltage (AC) 2 X 3 KW 120/208 120/220 120/240 1.5 gallons per batch Phase Wires KW Maximum Amp draw single 3 + ground 4.6 5.1 6.1 22.1 23.4 25.5 CBS-2052e Electrical Config. Code E52016 Universal Wiring Total 3 X 3 KW Heaters E52026 Universal Wiring Total 3 X 5 KW Heaters E53016 Universal Wiring Total 3 X 3 KW Heaters E53026 Universal Wiring Total 3 X 5 KW Heaters 7.
Dimensions & Utility Connections CBS-2051e DWG 201100-000 CBS-2052e DWG 201101-000 4
CBS-2052e20 DWG 201129-000 5
Installation (For Qualified Service Technicians Only) Keys To A Successful Installation If not installed correctly by qualified personnel, the brewer may not operate properly and damage may result. Damages resulting from improper installation are not covered by the warranty. Here are the key points to consider before installation: Electrical: All FETCO brewers require NEUTRAL. Ground is not an acceptable substitute. Installation without neutral may cause damage to the electronic components.
Electrical Connection 1. Verify that the actual voltage at the electrical service connection is compatible with the specifications on the brewer’s serial number label. Make sure the electrical service includes neutral. 2. The temperature and water tank fill level are pre-set at the factory. There is no need to turn off the heaters during the installation process. The heaters are disabled by the control board until the tank is full of water.
Final Setup 1. Turn on the incoming water supply line and inspect both inside and outside of the brewer for leaks in all fittings and tubes 2. Turn on the incoming power. 3. Press the brewer’s main power switch, which is hidden behind the front leg of the brewer. The control panel on/off switch will begin flashing. Press this switch. 4. Within 6 seconds, the hot water tank will begin filling until the water is sensed by the probe at the top of the tank. The display will read “FIL”.
Operating Instructions Control Panel Functions Only switches that are active are illuminated. Switches that are inactive or disabled are invisible. X Main Power Switch Controls all power to brewer Indicator lamp at top of panel. Y Control Panel On/Off Switch Secondary power switch. Does not disconnect main power. Flashing = Off Lit = On Invisible = Main Power Off Z Display ”FIL” = Water tank is filling. ”LO XXX” = Unit is heating, not ready to brew.
Programming Display Batch Settings Turn the brewer off by pressing the main power switch. Press the main power switch again to turn the unit on. The last 2 digits of the model number will display briefly, then S t b. Quickly hold the STOP button for 3 seconds. The display will show the software version. Example: Press STOP to continue. Batches are numbered 1 – 3 (CBS-2051e) or 1 – 6 (CBS-2052e / 2052e20) 52 Stb PrG 0.0 4.8 PARAMETER SETTING BATCH # 1.1 1.
Temperature Settings Parameter Name Range Default Setting Comment 7 Water Temp. (°F) 180°F - 208°F 200°F 8 Hot Water Service A (auto) / On / Off A (auto) 9 Brew at Set Temperature 0-1 1 Inside tank. Will be slightly lower at spray head. To display in ° Celsius, see # 58 in Advanced Settings. A= Faucet will dispense only when not brewing. On=Faucet always enabled. Off=Faucet always disabled. 0=Will brew at any temperature above 180°F. 1=Will brew only at set temperature.
Address 60 and 61 Description Left Brew Valve Flow Rate Right Brew Valve Flow Rate Range Default 0.09 – 1.49 If #59 is GAL or 0.33 – 5.63 If #59 is LTR 62 and 63 Left Bypass Valve Flow Rate Right Bypass Valve Flow Rate Comment 0.92 0.28 – 0.38 3.48 0.33 If #59 is GAL Use this to compensate for minor discrepancies in actual volume versus programmed volume. Set lower to increase volume, higher to decrease volume.
Error Codes Code Description Possible Cause Corrective Action 001 Internal Error System had to reload default settings. Control board failure. 050 Shorted temperature probe. Probe failure. Clear error. Re-program the brewer to the desired specifications. If error occurs again, replace control board. Replace probe. 051 Open temperature probe. 075 Brew basket lock or sensor failure. Basket was in place when brew cycle started, but was pulled out during the brew cycle.
Parts Figure 1 – CBS-2051e Main Assembly DWG 101191-B ITEM # QTY 1 2 2 3 4 5 6 7 8 9 10 11 11 11 12 13 14 15 16 17 1 1 1 1 1 1 4 1 1 2 2 1 1 4 20 1 1 1 1 PART # 001049 57006 57017 24012 31078 03074 82020 31031 86040 86032 29020 102192 102193 57073 83051 84002 002065 33007 108003 46029 DESCRIPTION WELDMENT CBS-2051e FILL VALVE, S-53 120VAC FILL VALVE, S-53 220VAC GASKET, S-53 FILL VALVE FITTING, S-53 FILL VALVE INLET BRACKET, S-53 SCREW, S-53 FILL VALVE FITTING, 90° MALE ELBOW, 3/8 TUBE OD X 3/8 MPT
18 19 20 20 21 22 23 24 25 26 27 28 28 29 29 30 31 32 32 32 33 34 35 35 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 58 59 60 61 62 63 64 4 4 1 1 4 1 1 12 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6 1 1 3 1 1 1 1 1 2 1 1 1 1 11 1 4 1 15007 29007 51042 51055 29019 65002 52050 83026 104029 22057 22058 102102 102159 101160 101174 102147 102207 57044 57077 57073 84030 45081 102189 52026 58054 25090 25044 25042 25104 25105 25106 25045 25046 25060 25061 86007 86036 86039 86038 402
Figure 2 – CBS-2051e Tank Assembly DWG 104029-C ITEM # QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1 1 1 1 1 1 1 1 1 1 3 2 1 1 1 2 1 PART # 4039 83041 31005 31116 83043 83048 31077 31150 31118 31151 31021 107002 84007 31152 13055 31128 31027 DESCRIPTION WELDMENT, TANK CBS-2051e WASHER, .812"OD X .412"ID, FLAT FITTING, 90 ELBOW, 1/4 HOSE ID X 1/8 MPT LOCKNUT 1/8 STRAIGHT PIPE THREAD WASHER, 1.125"OD X 0.688"ID FLAT WASHER, 1.250"OD X 0.
18 19 20 21 22 23 24 25 26 27 28 29 30 31 1 3 1 3 1 1 1 1 2 2 8 8 2 2 13072 83042 31036 31117 25098 31081 24002 102013 3332 53064 83011 84001 3297 59008 OUTLET, INSIDE TANK HOT WATER WASHER, .875"OD X .562"ID, FLAT FITTING COMPR.
Figure 3 – CBS-2052e / 2052e20 Main Assembly DWG 101197-B ITEM # QTY 2 3 4 5 5 5 6 7 8 8 9 10 12 12 13 14 15 15 16 17 18 2 2 2 1 1 1 1 1 1 1 18 32 1 1 9 4 1 1 2 2 1 PART # 86021 86018 86032 102189 52026 58054 102104 65002 57001 57022 83026 84002 108005 108065 29007 15007 51042 51055 29019 29020 102192 DESCRIPTION BUSHING, SNAP, 1.375 MTG HOLE PLUG, DOME, 1.
18 18 19 20 21 22 23 24 24 25 26 27 27 27 28 28 28 29 29 30 31 32 33 34 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 58 58 59 60 61 64 1 1 6 1 1 1 2 2 2 1 1 1 1 1 2 2 1 1 1 4 1 1 4 1 2 2 2 2 2 1 1 5 2 2 2 1 1 1 1 1 2 1 1 1 1 1 1 11 2 3 102193 57073 102202 83051 002065 33007 45082 102102 102159 102147 46029 57043 57076 57073 57044 57077 57073 101160 101174 22036 22037 104026 84030 32050 13122 86007 25046 25045 25044 25042 25060 25061 25106 25105 86038 86036 86039 102207 102172 44019
Figure 4 – CBS-2052e / 2052e20 Tank Assembly DWG 104026-A ITEM # QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 3 1 1 1 1 2 1 1 2 2 2 2 2 2 2 2 2 3 1 PART # 004038 31021 84007 31082 34004 31054 31027 31128 13072 83048 83043 31150 31077 31151 31118 83041 31005 31116 83042 25098 DESCRIPTION WELDMENT, TANK CBS-2052e BUSHING, 3/4-16 X 1/4 NPSM, HEX HEAD NUT, 3/4-16 HEX JAM FITTING, HEX NIPPLE, 3/8 MPT X 1/4 MPT VALVE, BALL 3/8 FPT X 3/8 FPT FITTING, 1/2 HOSE ID X 3/8 MPT FITTING, COMPR 90° MAL
22 23 24 25 26 27 28 28 29 30 31 32 1 3 3 12 12 3 1 3 3 3 3 1 1 31036 03332 53064 83011 84001 31117 31081 107002 107018 03297 59008 24002 102013 FITTING COMPR. MALE CONNECTOR 1/4 TUBE OD X 1/4 MPT BRACKET 2, ONE SHOT THERMOSTAT THERMOSTAT, SINGLE SHOT,TRIAC WASHER, #6 SCREW SIZE, INTERNAL NUT, HEX, #6-32 MACHINE SCREW LOCKNUT 1/4 STRAIGHT PIPE THREAD PLUG, HEX HEAD 1/4" MPT HEATER ASSY., 3000W, 240VAC HEATER ASSY.
Figure 5 – Spray Housing Assembly, 120 VAC, Part # 102102 Spray Housing Assembly, 220 VAC, Part # 102159 (EXPORT ONLY) ITEM # QTY 1 2 4 1 2 3 4 5 6 1 1 1 1 1 PART # DESCRIPTION 82112 #8 X 3/4'' PAN HD. PHIL. T.S. 18-8 S.S. SCREW 57042 VALVE ASSY., DSV-10, 120 VAC 57075 57072 102113 24035 102108 VALVE ASSY., DSV-10, 240 VAC VALVE REBUILD KIT, DSV-10 SPRAY HOUSING ASSY. O-RING, 5.5 I.D. X 5 11/16 O.D. X 3/32 SPRAY PLATE ASSY., 5 7/8" DIA.
Figure 6 – Brew Basket Assembly, 16” X 6”, Part # 101165 ITEM QTY 1 1 82096 HANDLE SCREW 2 1 23117 3 1 NOT SHOWN 1 NOT SHOWN PART # DESCRIPTION BREW BASKET HANDLE, BLACK (includes magnet) 9006 WIRE INSERT, 16 X 6 46011 WARNING LABEL F001 PAPER FILTERS, 15” X 5.
