I N S TA L L AT I O N G U I D E
IMPORTANT Dimensions in parentheses are in inches. Weights in parentheses are in pounds. Temperatures in parentheses are in Fahrenheit degrees.
Installation Guide Index Important Instructions Page 2 Important safety instructions Children safety Technical requirements 4 Appliance features and installation requirements 5 Installation niche features: Integrated 6 Installation niche features: Classic 7 Installation niche features: StandPlus 8 Installation niche features: X-Pro Preparing to install 9 Transport to installation site and unpacking 10 Electrical and Water connection 13 Levelling Panels mounting 14 Decorative door and Bot
2 www.fhiaba.com · info@fhiaba.
Installation Guide Important safely instruction Symbols used in the Guide Note Tips for the correct use of the appliance Important Directions to avoid appliance damage Warning directions to prevent injury Children safety If this appliance is replacing an existing appliance which must be removed or disposed of, make sure that it does not become a dangerous trap for children by cutting its power supply cable and rendering it impossible to close the door.
Appliance features and installation requirements Appliance dimensions Integrated 599 Series 749 Series 899 Series w: 599 mm (23 5/8”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”) w: 749 mm (29 1/2”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”) w: 899 mm (35 3/8”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”) Appliance dimensions Classic 599 Series 749 Series 899 Series w: 599 mm (23 5/8”)/ h: 2050 mm (80 3/4”))/ d: 635 mm (25”) w: 749 mm (29 1/2”)/ h: 2050 mm (80 3/4”))/ d: 635 mm (25”) w: 899 mm (35 3/8”)/ h: 2050 mm (8
Installation Guide Installation niche features: Integrated Series A area to be left clear for the anti-tipping brackets Door Opening Angle E area to be left clear for the power supply cable W and water supply hose 105° Width Minimum Niche Height S899: 899 mm (35 3/8”) S749: 749 mm (29 1/2”) S599: 599 mm (23 5/8”) 2064 mm (81 1/4”) Minimum Niche Width Height S899: 900 mm (35 1/2”) S749: 750 mm (29 5/8”) S599: 600 mm (23 3/4”) 2050 mm (80 3/4”) + 25 mm (1”) Door Swing Clearance 610 mm (24”) Depth
Installation niche features: Classic Series A area to be left clear for the anti-tipping brackets Door Opening Angle E area to be left clear for the power supply cable W and water supply hose 105° Width Minimum Niche Height KS899: 899 mm (35 3/8”) KS749: 749 mm (29 1/2”) KS599: 599 mm (23 5/8”) 2064 mm (81 1/4”) Minimum Niche Width Height KS899: 900 mm (35 1/2”) KS749: 750 mm (29 5/8”) KS599: 600 mm (23 3/4”) 2050 mm (80 3/4”) + 25 mm (1”) Door Swing Clearance 635 mm (25”) Depth with door KS899:
Installation Guide Installation niche features: StanPlus60 Series A area to be left clear for the anti-tipping brackets Door Opening Angle E area to be left clear for the power supply cable W and water supply hose 105° Width Minimum Niche Height MS899: 899 mm (35 3/8”) MS749: 749 mm (29 1/2”) MS599: 599 mm (23 5/8”) 2134 mm (84”) Minimum Niche Width Height MS899: 900 mm (35 1/2”) MS749: 750 mm (29 5/8”) MS599: 600 mm (23 3/4”) 2120 mm (83 1/2”) + 25 mm (1”) Door Swing Clearance 629 mm (24 3/4”)
Installation niche features: X-Pro Series A area to be left clear for the anti-tipping brackets Door Opening Angle E area to be left clear for the power supply cable W and water supply hose 105° Width Minimum Niche Height XS899: 899 mm (35 3/8”) XS749: 749 mm (29 1/2”) XS599: 599 mm (23 5/8”) 2134 mm (84”) Minimum Niche Width Height XS899: 900 mm (35 1/2”) XS749: 750 mm (29 5/8”) XS599: 600 mm (23 3/4”) 2120 mm (83 1/2”) + 25 mm (1”) Door Swing Clearance 635 mm (25 ”) Depth with door XS899: 1470
Installation Guide Series: All Preparing the installation Transport to installation site and unpacking Since this is a large and heavy appliance, before transporting the appliance, check the access to the location where it will be installed (door size, manoeuvring space in stairwells, etc.). The appliance is attached to the base of the packaging (pallet) through four bolts which can be removed using a 17 mm (3/4”) wrench.
Series: All Electrical and Water connection E W W E A Schuko 16 A socket with an efÀcient grounding should be made available for the electrical mains connection, as well as an omnipolar switch which can easily be reached when the appliance is installed. To connect to the water supply system (for appliances equipped with ice makers) a tap with a male 3/4” connection should be provided, which must also be easily accessible once the appliance is installed.
Installation Guide Series: Integrated/Classic Back of appliance Electrical connection Water connection Operate as follows: 1 Unwind the electric cable and connect it directly to the wall socket. Make sure the appliance is in the Stand-by condition and that all lights are off; should it be not so press the Unit button to switch it off. Fit one end of the water hose onto the connector at the appliance’s back 1 .
Series: StandPlus/X-Pro Back of appliance Electrical connection Water connection Front of appliance Operate as follows: 1 Unwind the electric cable and connect it directly to the wall socket. Make sure the appliance is in the Stand-by condition and that all ights are off; should it be not so press the Unit button to switch it off. Connect the water line to the threaded connection at the base of the unit, as in Àgure 1 .
Installation Guide Series: All Levelling Adjust the appliance level by means of the front levelling feet and the rear adjustable wheels. Operate as follows: After removing the bottom plinth or grille (it is kept in position by magnets), adjust the height of the levelling feet 1 by means of a 17 mm (3/4”) open spanner. 2 1 2 Then adjust the height of the rear wheels by turning the front adjusting bolts 2 clockwise or anticlockwise as it may be required. 1 Remount the bottom plinth or grille. www.
Series: Integrated Decorative door and bottom-drawer panels layout The dimensions of the panels are indicated in the table and drawings on pages 18-21. Nevertheless, according to the requirements for aligning with other kitchen structures, the door panel can be higher than the upper edge of the refrigerator door, and the drawer panel can be lower than the edge of the drawer.
Installation Guide Series: Integrated 4 Position the brackets on each set of marks to make sure they are aligned 4 , then drill holes through the panel (pay close attention to the panel’s thickness) 5 . Screw the brackets in place 6 . 5 Drawer Panel When preparing the Drawer Panel, follow the same instructions as per the door panel, but make sure measurements are taken starting from the top edge 7 . The support bracket faces the opposite way 8 (note imgs 4 and 8). 7 8 www.fhiaba.com · info@fhiaba.
Series: Integrated Decorative panels layout for Fridge with one Bottom-Drawer (1T/0T) Series 899 Series 749 Series 599 Hinge Left Hinge Right Hinge Left Hinge Right Hinge Left Hinge Right A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”) B 355.5 (14”) 261 (10 ¼”) 279 (11”) 187 (7 3⁄8”) 205 (8 1⁄8”) 111 (4 3⁄8”) C 261 (10 ¼”) 355.5 (14”) 187 (7 3⁄8”) 279 (11”) 111 (4 3⁄8”) 205 (8 1⁄8”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) 276.
Installation Guide Series: Integrated Decorative panels layout for Fridge with two Bottom-Drawers (0H) Series 899 Series 749 Series 599 Hinge Left Hinge Right Hinge Left Hinge Right Hinge Left Hinge Right A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”) B 355.5 (14”) 261 (10 ¼”) 279 (11”) 187 (7 3⁄8”) 205 (8 1⁄8”) 111 (4 3⁄8”) C 261 (10 ¼”) 355.
Series: Integrated Decorative panels layout for Fridge with glass door and one Bottom-Drawer (1T/0T) Series 899 Series 749 Series 599 Hinge Left Hinge Right Hinge Left Hinge Right Hinge Left Hinge Right A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) 276.5 (10 7⁄8”) 236.5 (9 3⁄8”) E 386 (15 ¼”) 418 (16 ½”) 311 (12 ¼”) 343 (13 ½”) 236.5 (9 3⁄8”) 276.5 (10 7⁄8”) F/G 354.5 (14”) 354.5 (14”) 279.
Installation Guide Series: Integrated Decorative panels layout for Fridge with glass door and two Bottom-Drawers (0H) Series 899 Series 749 Series 599 Hinge Left Hinge Right Hinge Left Hinge Right Hinge Left Hinge Right A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) 276.5 (10 7⁄8”) 236.5 (9 3⁄8”) E 386 (15 ¼”) 418 (16 ½”) 311 (12 ¼”) 343 (13 ½”) 236.5 (9 3⁄8”) 276.5 (10 7⁄8”) F/G 354.
Series: Integrated Panels Dimensions One Bottom - Drawer (1T/0T models) Panels with width ranging between 18 mm (3/4 in) and 28 mm (1 1/8 in).
Installation Guide Series: Integrated Panels DimensionsTwo Bottom - Drawers (0H models) Panels with width ranging between 18 mm (3/4 in) and 28 mm (1 1/8 in).
Series: Integrated Mounting the handles 1 Handles will have to be mounted on the panels before they are applied to the fridge. Operate as follows: Drill two holes on the back of the panels according to the table below 1 . Place the handle on top of the holes and insert the screws through the panel and into the handle support 2 .
Installation Guide Series: Integrated Mounting panels to the door and the drawer Once all brackets and small brackets have been applied to the panels, you can begin installing the bottom drawer. 1 Operate as follows: Partially tighten the screw to the Àxing 2 1 . Hook the bottom drawer panel starting from the Àxings on the bottom 2 .
Series: Integrated Hook the panel to the fixing devices starting from the top aligning brackets 6 . 6 7 At this point, alignment between the panel and adjacent cabinets can be adjusted using the alignment brackets and small brackets 7 and 8 . Vertical alignment: tighten or loosen the screw in the brackets to raise or lower the panel 9 .
Installation Guide Series: All Installation Built-in installation single appliance 1 For a built-in installation, to close gaps between the appliance and the adjacent cabinets, special side proÀles and aluminum covering frames are provided. Operate as follows: Push the appliance into the installation niche 1 .
Series: All Built-in installation two or more appliances Required accessories to be ordered separately: Central connection Kit (KCC) Special side proÀles and aluminum covering frames are provided for closing gaps between the appliance and the adjacent cabinets. 1 Operate as follows: Position the appliances in front of the installation area, leaving enugh space to operate at their back 1 .
Installation Guide Series: All 6 Once completed the previous steps, push the units in their Ànal position 6 . If the units are to be installed inside a niche or within an enclosed structure, it is necessary to design a ventilation shaft at the back of the niche to assure proper ventilation at the back of the unit. A 5 mm gap is sufÀcient to prevent overheating. Always mount front panels on door and drawer before pushing the unit into its Ànal position inside the niche or structure.
Series: Integrated/Classic Free-standing installation two or more appliances Required accessories to be ordered separately: Central Connection Kit (KCC) Freestanding Kit 1 Aluminium proÀles can be used to close the spaces between the appliance and adjacent structures. Operate as follows: Position the appliances in front of the installation area, leaving enough space to operate at their back.
Installation Guide Series: Integrated/Classic 7 Attach the side panels to the unit, mounting them on the side proÀles 7 pre-mounted on the unit. Attach the aluminum cover 8 to each side proÀle, pressing onto them until they ‘click’ together. 8 Mount the top panel 9 on top of the unit, using the screws provided with the kit. Adjust the height of the unit with the leveling feet and the back wheels.
Series: Integrated/Classic Anti-tipping safety assembly 1 5⁄8” ) 59 (2 3⁄8”) 45 ( 152 (6”) To prevent the appliance from tipping over an extra-long kit is vailable up on request if the appliance needs to remain distanced from the wall, it is mandatory to install two brackets on the upper part of the appliance for Àxing it securely to the wall. Operate as follows: 1 The brackets should be applied as illustrated using the provided screws and expansion plugs.
Installation Guide Series: StandPlus/X-Pro Anti-tipping safety assembly To avoid danger of the appliance tipping over when opening full doors and drawers, it is mandatory to install two brackets on the upper part of the appliance for Àxing it securely to the wall. The brackets should be applied as illustrated using the provided screws and expansion plugs. 1 Operate as follows: Place a bracket on the top of the appliance in correspondence to the Àxing holes and against the wall 1 .
Series: Classic/StandPlus/X-Pro Mounting the handles on stainless front 1 To mount the handles onto the door and the drawer operate as follows: Operate as follows: Insert the two handle spacers onto the supports already available on the door and the drawer 1 . Screw in the Allen screws available on the handle 2 . 2 The screws must be tightened in by means of a 2.5 mm (1/8”) hex wrench. 32 www.fhiaba.com · info@fhiaba.
Installation Guide Series: Integrated/Classic Ventilation A forced air system assures ventilation through a grille positioned in the lower front part of the unit. If the kitchen design includes a kickplate, the latter has to be punched in order to maintain a satisfactory air Áow, as described in the drawing. Holes can be in any shape and size, as long as the total area of the punched part equals 50% of the kickplate are.
Series: StandPlus/X-Pro Ventilation Ventilation is insured by a forced air system through a grille located in the upper part of the appliance. This grille should never be covered by panels or any other devices that could reduce its efÀciency. Please refer to page 5-6 to ensure correct air circulation. 34 www.fhiaba.com · info@fhiaba.
Installation Guide Series: All Post installation control Check that the front levelling feet have been properly installed. Check that the connection to the water system does not have any leaks and that the closing tap is easily accessible. Check that the electrical connection is correctly installed and that the multipole switch and socket are easily accessible. Check the perfect alignment of the appliance with adjacent structures.
Series: All Start up To start the appliance, connect the plug to the electrical mains: at this point, when opening the door, the control panel will usually visualize the message “Stand by”, and all the panel keys be off UNIT Before starting Before starting Electronic Control UNIT FRIDGE 1 2 3 4 5 6 ENTER ICE MAKER 7 8 9 Unit Switches the appliance (all compartments) between ON and STAND BY (press for three seconds).
29-04-2014 Installation Guide Baron Industries srl is constantly researching new way to improve the features and the design of their products, therefore models are often upgraded and reviewed. Fhiaba srl Via Fiumicino, 20 · 33082 · Azzano Decimo · PN · Italy · Tel +39 0434 420160 · Fax +39 0434 420161 E-mail: info@fhiaba.com · www.fhiaba.
B09000700 EN www. f hi a b a . c o m Info Line 800 - Fhiaba .