INSTALLATION GUIDE EN NOTICE D’INSTALLATION FR
IMPORTANT Dimensions in parentheses are in inches: mm(in). Weights in parentheses are in pounds: kg (lb).
Installation Guide Index Important Instructions Page 3 Important safety instructions Children safety Technical requirements 3 Appliance features and installation requirements 4 Integrated installation niche features 5 StandPlus installation niche features 6 X-Pro installation niche features 7 Transport to installation site and unpacking 8 Niche Dimensions and Installation Styles: Integrated Series 8 Niche Dimensions and Installation Styles: StandPlus and X-Pro Series 9 Installation types
2 www.fhiaba.com · www.thevettagroup.
Installation Guide Series: All Important safely instruction Note Tips for the correct use of the appliance Symbols used in the Guide Important Directions to avoid appliance damage Warning directions to prevent injury If this appliance is replacing an existing appliance which must be removed or disposed of, make sure that it does not become a dangerous trap for children by cutting its power supply cable and rendering it impossible to close the door.
Installation niche features: Integrated Series A area to be left clear for the anti-tipping brackets Door Opening Angle 105° Niche Height 2134 mm (84”) Width FI36: 899 mm (35 3/8”) FI30: 749 mm (29 1/2”) FI24: 599 mm (23 5/8”) Niche Width FI36: 900 mm (35 1/2”) FI30: 750 mm (29 5/8”) FI24: 600 mm (23 3/4”) Height 2120 mm (83 1/2”) + 25 mm (1”) Door Swing Clearance Depth with door (without panel) FI36: 1470 mm (57 7/8”) FI30: 1320 mm (52”) FI24: 1170 mm (46”) A A FI36: 160 (6 3⁄8”) FI30: 125 (5”) F
Installation Guide Installation niche features: StandPlus Series A area to be left clear for the anti-tipping brackets Door Opening Angle 105° Niche Height 2134 mm (84”) Width FM36: 899 mm (35 3/8”) FM24: 599 mm (23 5/8”) Niche Width FM36: 900 mm (35 1/2”) FM24: 600 mm (23 3/4”) Height 2120 mm (83 1/2”) + 25 mm (1”) Door Swing Clearance Depth with door FM36: 1470 mm (57 7/8”) FM24: 1170 mm (46”) A FM36: 1470 (57 7⁄8”) FM24: 1170 (46”) 1010 (39 ¾”) A FM36: 230 (9”) FM24: 160 (6 ¼”) 100 (4”) 140
Installation niche features: X-Pro Series A area to be left clear for the anti-tipping brackets Door Opening Angle 105° Niche Height 2134 mm (84”) Width FP36: 899 mm (35 3/8”) FP30: 749 mm (29 1/2”) FP24: 599 mm (23 5/8”) Niche Width FP36: 900 mm (35 1/2”) FP30: 750 mm (29 5/8”) FP24: 600 mm (23 3/4”) Height 2120 mm (83 1/2”) + 25 mm (1”) Door Swing Clearance Depth with door FP36: 1470 mm (57 7/8”) FP30: 1320 mm (52”) FP24: 1170 mm (46”) A FP36: 1470 (57 7⁄8”) FP30: 1320 (52”) FP24: 1170 (46”) 1016
Installation Guide Series: All Preparing the installation Transport to installation site and unpacking Since this is a large and heavy appliance, before transporting the appliance, check the access to the location where it will be installed (door size, manoeuvring space in stairwells, etc.). The appliance should always be transported in an erect position. If this is not possible, transport the appliance laying on its rear side.
Series: All Niche Dimensions and Installation Styles: Integrated Series FI36: 900 (35 ½”) Series Niche Panels Width FI36 900 (35 1/2”) 897 (35 1/4”) FI30 750 (29 5/8”) 747 (29 3/8”) FI24 600 (23 3/4”) 597 (23 1/2”) FI30: 750 (29 5⁄8”) FI24: 600 (23 ¾”) A B A A KCLITU: Lateral connection Kit (not included - must be ordered as a separate accessory) B KCCITU: Central connection Kit (not included - must be ordered as a separate accessory) Niche Dimensions and Installation Styles: StandPlus a
Installation Guide Series: All Installation types Flush installation with standard aluminum trims A B 6,5 (¼”) English A KCLITU: Lateral connection Kit (not included - must be ordered as a separate accessory) B KCCITU: Central connection Kit (not included - must be ordered as a separate accessory) Prominent installation with standard aluminum trims A B Français A KCLITU: Lateral connection Kit (not included - must be ordered as a separate accessory) B KCCITU: Central connection Kit (not included -
Series: All Electrical and Water connection E W The appliances are delivered from the factory for operation at 110V120V AC - 60Hz (US and Canada). They are provided with a suitable supply cable and plug to be connected to an appropriate 15A socket (US and Canada) provided with an effective grounding. A circuit breaker should also be installed and should be easily accessible so that it can be easily switched off before performing any installation or maintenance.
Installation Guide Series: Integrated Back of appliance Electrical connection English Water connection Unwind the electric cable and connect it directly to the wall socket. Make sure the appliance is in the Stand-by condition and that all lights are off; should it be not so press the Unit button to switch it off. Push the 1/4” source waterline fully into the elbow connector then thread the elbow adapter to the solenoid at the back of the appliance.
Series: StandPlus/X-Pro Back of appliance Electrical connection Water connection Operate as follows: Front of appliance 1 Unwind the electric cable and connect it directly to the wall socket. Make sure the appliance is in the Stand-by condition and that all ights are off; should it be not so press the Unit button to switch it off. Connect the water line to the threaded connection at the base of the unit, as in Àgure 1 . 2 12 www.fhiaba.com · www.thevettagroup.
Installation Guide Series: All Levelling Adjust the appliance level by means of the front levelling feet and the rear adjustable wheels. Operate as follows: Then adjust the height of the rear wheels by turning the front adjusting bolts 2 clockwise or anticlockwise as it may be required. 1 2 1 Remount the bottom plinth or grille.
Series: Integrated Decorative door and bottom-drawer panels layout The dimensions of the panels are indicated in the table and drawings on pages 16-19. Nevertheless, according to the requirements for aligning with other kitchen structures, the door panel can be higher than the upper edge of the refrigerator door, and the drawer panel can be lower than the edge of the drawer.
Installation Guide Series: Integrated 4 Position the brackets on each set of marks to make sure they are aligned 4 , then drill holes through the panel (pay close attention to the panel’s thickness) 5 . English Screw the brackets in place 6 . 5 Drawer Panel Français When preparing the Drawer Panel, follow the same instructions as per the door panel, but make sure measurements are taken starting from the top edge 7 . The support bracket faces the opposite way 8 (note imgs 4 and 8). 7 8 www.fhiaba.
Series: Integrated Decorative panels layout for Fridge with one Bottom-Drawer Series 36 Series 30 Series 24 Hinge Left Hinge Right Hinge Left Hinge Right Hinge Left Hinge Right A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”) B 355.5 (14”) 261 (10 ¼”) 279 (11”) 187 (7 3⁄8”) 205 (8 1⁄8”) 111 (4 3⁄8”) C 261 (10 ¼”) 355.5 (14”) 187 (7 3⁄8”) 279 (11”) 111 (4 3⁄8”) 205 (8 1⁄8”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) 276.
Installation Guide Series: Integrated Decorative panels layout for Fridge with two Bottom-Drawers Series 30 Hinge Left Hinge Right Hinge Left Hinge Right A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) B 355.5 (14”) 261 (10 ¼”) 279 (11”) 187 (7 3⁄8”) C 261 (10 ¼”) 355.5 (14”) 187 (7 3⁄8”) 279 (11”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) E 386 (15 ¼”) 418 (16 ½”) 311 (12 ¼”) 343 (13 ½”) F/G 354.5 (14”) 354.5 (14”) 279.5 (11”) 279.
Series: Integrated Decorative panels layout for Fridge with glass door and one Bottom-Drawer Series 36 Series 30 Series 24 Hinge Left Hinge Right Hinge Left Hinge Right Hinge Left Hinge Right A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) 276.5 (10 7⁄8”) 236.5 (9 3⁄8”) E 386 (15 ¼”) 418 (16 ½”) 311 (12 ¼”) 343 (13 ½”) 236.5 (9 3⁄8”) 276.5 (10 7⁄8”) F/G 354.5 (14”) 354.5 (14”) 279.5 (11”) 279.
Installation Guide Series: Integrated Decorative panels layout for Fridge with glass door and two Bottom-Drawers Series 30 Hinge Left Hinge Right Hinge Left Hinge Right A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) E 386 (15 ¼”) 418 (16 ½”) 311 (12 ¼”) 343 (13 ½”) F/G 354.5 (14”) 354.5 (14”) 279.5 (11”) 279.
Series: Integrated Panels Dimensions Single Bottom - Drawer Panels can have thickness ranging between 18 mm (3/4”) and 28 mm (1-1/8“). Door panels can have a maximum weight 23 kg (51 lbs) and drawer panels may be a maximum weight of 11kg (25 lbs) Exceeding these weights could void your warranty for any service issues which can be attributed to overweight panels. The hinging mechanism on Fhiaba appliances is considered to be `Zero-clearance`.
Installation Guide Series: Integrated Panels Dimensions Two Bottom - Drawers Panels can have thickness ranging between 18 mm (3/4”) and 28 mm (1-1/8“). Door panels can have a maximum weight 23 kg (51 lbs) and drawer panels may be a maximum weight of 11kg (25 lbs) Exceeding these weights could void your warranty for any service issues which can be attributed to overweight panels. The hinging mechanism on Fhiaba appliances is considered to be `Zero-clearance`.
Series: Integrated Mounting the handles on Integrated units 1 Handles will have to be mounted on the panels before they are applied to the fridge. Operate as follows: Drill two holes of 5 mm (1/4 “) on the rear side panels, insert the supplied screws to the distance indicated in the the table below. To center the vertical handle (code HV) to the center of the door, split into two the height of the panel and make a hole at -45 cm (-17 3/4 “) and one at +45 cm (+17 3/4”) 1 .
Installation Guide Series: Integrated Mounting panels to the door and the drawer of Integrated units Once all brackets and small brackets have been applied to the panels, you can begin installing the bottom drawer. 1 Partially tighten the screw to the Àxing 1 . 2 English Operate as follows: It is now possible to align panels to adjacent cabinets in height using the lower alignment brackets, 3 tightening or untightening the screws into position as needed.
Series: Integrated Hook the panel to the fixing devices starting from the top aligning brackets 6 . 6 At this point, alignment between the panel and adjacent cabinets can be adjusted using the alignment brackets and small brackets 7 and 8 . 7 Vertical alignment: tighten or loosen the screw in the brackets to raise or lower the panel 9 .
Installation Guide Series: All IMPORTANT: The following instruction for installation apply to all Fhiaba models. Installation Built-in installation single appliance 1 For a built-in installation, to close gaps between the appliance and the adjacent cabinets, special side proÀles and aluminum covering frames are provided.
Series: All Built-in installation two or more appliances 1 Required accessories to be ordered separately: Central connection Kit (KCC) Special side proÀles and aluminum covering frames are provided for closing gaps between the appliance and the adjacent cabinets. Operate as follows: Position the appliances in front of the installation area, leaving enugh space to operate at their back 1 .
Installation Guide Series: All 5 Check the levelling of the appliance, adjusting its feet and wheels to correct it. English Once the previous steps are complete, push the units in their Ànal position 5 . If the units are to be installed inside a niche or within an enclosed structure, it is necessary to design a ventilation shaft at the back of the niche to assure proper ventilation at the back of the unit. A 5 mm gap is sufÀcient to prevent overheating.
Series: Integrated Anti-tipping safety assembly 1 5⁄8” ) 59 (2 3⁄8”) 45 ( 152 (6”) To prevent the appliance from tipping over an extra-long kit is vailable up on request if the appliance needs to remain distanced from the wall, it is mandatory to install two brackets on the upper part of the appliance for Àxing it securely to the wall. Operate as follows: 1 The brackets should be applied as illustrated using the provided screws and expansion plugs.
Installation Guide Series: StandPlus/X-Pro Anti-tipping safety assembly To avoid danger of the appliance tipping over when opening full doors and drawers, it is mandatory to install two brackets on the upper part of the appliance for Àxing it securely to the wall. The brackets should be applied as illustrated using the provided screws and expansion plugs. Operate as follows: Place a bracket on the top of the appliance in correspondence to the Àxing holes and against the wall 1 .
Series: StandPlus/X-Pro Mounting handles on stainless front 1 To mount the handles onto the door and the drawer operate as follows: Operate as follows: Insert the two handle spacers onto the supports already available on the door and the drawer 1 . Screw in the Allen screws available on the handle 2 . 2 The screws must be tightened in by means of a 2.5 mm (1/8”) hex wrench. 30 www.fhiaba.com · www.thevettagroup.
Installation Guide Series: Integrated Air circulation 36 Series 30 Series 24 Series A 860 (33 7⁄8”) 740 (29 1⁄8”) B > 100 (4”) C 10 (3⁄8”) 50% 560 (22”) C B C A www.fhiaba.com · www.thevettagroup.com 31 Français English A forced air system assures ventilation through a grille positioned in the lower front part of the unit. If the kitchen design includes a kickplate, the latter has to be punched in order to maintain a satisfactory air Áow, as described in the drawing.
Series: StandPlus/X-Pro Ventilation Ventilation is insured by a forced air system through a grille located in the upper part of the appliance. This grille should never be covered by panels or any other devices that could reduce its efÀciency. Please refer to page 5-6 to ensure correct air circulation. 32 www.fhiaba.com · www.thevettagroup.
Installation Guide Series: All Post installation control Check that the front levelling feet have been properly installed. Check that the connection to the water system does not have any leaks and that the closing tap is easily accessible. Check that the electrical connection is correctly installed and that the multipole switch and socket are easily accessible. Check the perfect alignment of the appliance with adjacent structures.
Series: All Start up To start the appliance, connect the plug to the electrical mains: at this point, when opening the door, the control panel will usually visualize the message “Stand by”, and all the panel keys be off UNIT Before starting Before starting Electronic Control UNIT FRIDGE 1 2 3 Unit 4 5 6 ENTER ICE MAKER 7 8 9 Switches the appliance (all compartments) between ON and STAND BY (press for three seconds).
Notice d’Installation Sommaire Indications importantes Page 3 Indications importantes concernant la sécurité Pour la sécurité des enfants Caractéristiques techniques 3 Caractéristiques de l’appareil et conditions requises pour l’installation 4 Caractéristiques de la niche d’installation Integrated 5 Caractéristiques de la niche d’installation StandPlus 6 Caractéristiques de la niche d’installation X-Pro 7 Transport sur le lieu d’installation et déballage 8 Dimensions de l’encastrement et Style
2 www.fhiaba.com · www.thevettagroup.
Notice d’Installation Indications importantes concernant la sécurité Symboles utilisés dans le manuel Important Indications aÀn d’éviter tout endommagement de l’appareil Note conseils pour une correcte utilisation de l’appareil Attention indications aÀn d’éviter toute lésion aux personnes Si cet appareil remplace un autre appareil déjà existant qui doit être mis de côté ou éliminé, veiller à ce que celui-ci ne devienne pas un dangereux piège pour les enfants, en coupant le câble d’alimentation et en rend
Caractéristiques de la niche d’installation: Série Integrated A espace à réserver aux équerres anti-renversement Angle d’ouverture de la porte 105° Hauteur de l’encastrement 2134 mm (84”) Largeur FI36: 899 mm (35 3/8”) FI30: 749 mm (29 1/2”) FI24: 599 mm (23 5/8”) Largeur de l’encastrement FI36: 900 mm (35 1/2”) FI30: 750 mm (29 5/8”) FI24: 600 mm (23 3/4”) Hauteur 2120 mm (83 1/2”) + 25 mm (1”) Encombrement avec porte ouverte Profondeur (sans panneau) FI36: 1470 mm (57 7/8”) FI30: 1320 mm (52”) FI24
Notice d’Installation Caractéristiques de la niche d’installation: Série StandPlus A espace à réserver aux équerres anti-renversement Angle d’ouverture de la porte 105° Hauteur de l’encastrement 2134 mm (84”) Largeur FM36: 899 mm (35 3/8”) FM24: 599 mm (23 5/8”) Largeur de l’encastrement FM36: 900 mm (35 1/2”) FM24: 600 mm (23 3/4”) Hauteur 2120 mm (83 1/2”) + 25 mm (1”) Encombrement avec porte ouverte Profondeur FM36: 1470 mm (57 7/8”) FM24: 1170 mm (46”) A FM36: 1470 (57 7⁄8”) FM24: 1170 (46”) 10
Caractéristiques de la niche d’installation: Série X-Pro A espace à réserver aux équerres anti-renversement Angle d’ouverture de la porte 105° Hauteur de l’encastrement 2134 mm (84”) Largeur FP36: 899 mm (35 3/8”) FP30: 749 mm (29 1/2”) FP24: 599 mm (23 5/8”) Largeur de l’encastrement FP36: 900 mm (35 1/2”) FP30: 750 mm (29 5/8”) FP24: 600 mm (23 3/4”) Hauteur 2120 mm (83 1/2”) + 25 mm (1”) Encombrement avec porte ouverte Profondeur FP36: 1470 mm (57 7/8”) FP30: 1320 mm (52”) FP24: 1170 mm (46”) A
Notice d’Installation Série: tous Préparation à l’installation Transport sur le lieu d’installation et déballage S’agissant d’un appareil lourd et de grandes dimensions, avant de transporter l’appareil, s’informer sur les modalités d’accès au lieu où il sera installé (dimensions des portes, espaces de mouvement dans les escaliers, etc.). L’appareil est Àxé à la base de l’emballage (palette) moyennant quatre boulons amovibles avec une clé de 17 mm (3/4»).
Série: tous Dimensions de l’encastrement et Styles d’installation: Série Integrated FI36: 900 (35 ½”) Série Niche Largeur de panneaux FI36 900 (35 1/2”) 897 (35 1/4”) FI30 750 (29 5/8”) 747 (29 3/8”) FI24 600 (23 3/4”) 597 (23 1/2”) FI30: 750 (29 5⁄8”) FI24: 600 (23 ¾”) A B A A KCLIT: Kit raccordement lateral (non compris - doit être commandé comme accessoire séparé) B KCCIT: Kit raccordement central (non compris - doit être commandé comme accessoire séparé) Dimensions de l’encastrement
Notice d’Installation Série: tous Types d’installation Montage à Áeur avec des garnitures en aluminium standards A B A KCLIT: Kit raccordement lateral (non compris - doit être commandé comme accessoire séparé) B KCCIT: Kit raccordement central (non compris - doit être commandé comme accessoire séparé) English 6,5 (¼”) L’installation Prominent avec des garnitures en aluminium standards A B Français A KCLIT: Kit raccordement lateral (non compris - doit être commandé comme accessoire séparé) B KCCIT:
Série: tous Raccordements électrique et hydraulique E W Les appareils sont livrés de l’usine pour le fonctionnement à 230V AC - 50Hz (Europe, Royaume Uni et autres Pays) ou 115V AC - 60Hz (EtatsUnis et Canada). Un câble d’alimentation avec Àche équipé d’un contact de terre sont fournis pour la connexion à une prise de 16A (Europe, Royaume Uni et autres Pays) ou de 15A (Etats-Unis et Canada) .
Notice d’Installation Série: Integrated Arrière de l’appareil Branchement Électrique English Raccordement Hydraulique Dérouler le câble électrique et le brancher directement à la prise murale. Contrôler que l’appareil soit en stand-by et que les voyants soient éteints; dans le cas contraire, appuyer sur la touche Unit pour éteindre l’appareil. Raccorder le tuyau de l’eau au réfrigérateur dans la zone arrière.
Série: StandPlus/X-Pro Arrière de l’appareil Branchement Électrique Raccordement Hydraulique Intervenir de la manière suivante: Avant de l’appareil Dérouler le câble électrique et le brancher directement à la prise murale. 1 Contrôler que l’appareil soit en stand-by et que les voyants soient éteints; dans le cas contraire, appuyer sur la touche Unit pour éteindre l’appareil. Reliez l’entrée d’eau avec la connection taraudée à la base de l’appareil 1 . 2 12 www.fhiaba.com · www.thevettagroup.
Notice d’Installation Série: tous Mise à niveau Mettre à niveau l’appareil en réglant les pieds et les roues arrière à la base de l’appareil. Intervenir de la manière suivante: Ensuite régler l’hauteur des roues arrière en tournant les boulons de réglage 2 dans le sens horaire ou anti-horaire comme nécessaire. Remonter le socle (ou grille) inférieur ou la grille.
Série: Integrated Préparation des panneaux décoratifs pour la porte et Grands bacs Les dimensions des panneaux sont indiquées dans le tableau et sur les dessins reportés ci-dessous. Selon les exigences d’alignement avec d’autres meubles de la cuisine, le panneau de la porte du réfrigérateur peut être plus haut par rapport à la ligne supérieure de la porte et le panneau inférieur peut être plus bas par rapport à la ligne inférieure du grand bac.
Notice d’Installation Série: Integrated 4 VériÀer la position des trous en appuyant les équerres sur les marques 4 puis pratiquer les trous en faisant attention à l’épaisseur du panneau 5 . English Visser les équerres 6 .
Série: Integrated Préparation des panneaux décoratifs pour Réfrigérateur avec un Grand bac Série 36 Série 30 Série 599 Charnière Gauche Charnière Droite Charnière Gauche Charnière Droite Charnière Gauche Charnière Droite A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”) B 355.5 (14”) 261 (10 ¼”) 279 (11”) 187 (7 3⁄8”) 205 (8 1⁄8”) 111 (4 3⁄8”) C 261 (10 ¼”) 355.
Notice d’Installation Série: Integrated Préparation des panneaux décoratifs pour Réfrigérateur avec deux Grands bacs Série 30 Charnière Droite Charnière Gauche Charnière Droite A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) B 355.5 (14”) 261 (10 ¼”) 279 (11”) 187 (7 3⁄8”) C 261 (10 ¼”) 355.5 (14”) 187 (7 3⁄8”) 279 (11”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) E 386 (15 ¼”) 418 (16 ½”) 311 (12 ¼”) 343 (13 ½”) F/G 354.5 (14”) 354.5 (14”) 279.5 (11”) 279.
Série: Iintegrated Préparation des panneaux décoratifs pour Réfrigérateur avec porte vitrée et un Grand bac Série 36 Série 24 Série 30 Charnière Gauche Charnière Droite Charnière Gauche Charnière Droite Charnière Gauche Charnière Droite A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) 276.5 (10 7⁄8”) 236.5 (9 3⁄8”) E 386 (15 ¼”) 418 (16 ½”) 311 (12 ¼”) 343 (13 ½”) 236.5 (9 3⁄8”) 276.
Notice d’Installation Série: Integrated Préparation des panneaux décoratifs pour Réfrigérateur avec porte vitrée et deux Grands bacs Série 30 Charnière Droite Charnière Gauche Charnière Droite A 897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) D 418 (16 ½”) 386 (15 ¼”) 343 (13 ½”) 311 (12 ¼”) E 386 (15 ¼”) 418 (16 ½”) 311 (12 ¼”) 343 (13 ½”) F/G 354.5 (14”) 354.5 (14”) 279.5 (11”) 279.
Série: Integrated Dimensions des panneaux - Modèles avec un Grand Bac Il est possible d’utiliser des panneaux avec des épaisseurs allant entre 18 mm (3/4 in) et 28 mm (1 1/8 in). Les panneaux de porte avec un poids max de 23 kg (51 lb) et panneaux de grand bac avec poids max de 11 kg (25 lb) Excéder ces poids pourrait annuler la garantie de tous les problèmes de services qui peuvent être attribués à des panneaux en surpoids.
Notice d’Installation Série: Integrated Dimensions des panneaux - Modèles avec deux Grands bacs Il est possible d’utiliser des panneaux avec des épaisseurs allant entre 18 mm (3/4 in) et 28 mm (1 1/8 in). Les panneaux de porte avec un poids max de 23 kg (51 lb) et panneaux de grand bac avec poids max de 11 kg (25 lb) Excéder ces poids pourrait annuler la garantie de tous les problèmes de services qui peuvent être attribués à des panneaux en surpoids.
Série: Integrated Montage des poignées: Sèrie Integrated 1 Les poignées doivent être montées sur le panneau décoratif de la porte et du grand bac avant que les panneaux ne soient Àxés au réfrigérateur. Intervenir de la manière suivante: Après avoir pratiqué deux trous de 5 mm (1/4”) sur le côté arrière des panneaux, insérer les vis fournies à la distance indiquée sur le tableau, reportée ci-dessous, l’une de l’autre.
Notice d’Installation Série: Integrated Fixation des panneaux à la porte et au Grand bac: Sèrie Integrated Aprés avoir appliqué les pattes de Àxation et les équerres aux panneaux, commencer l’installation par le tiroir du bas. 1 Serrer les vis que partiellement aux Àxations inférieures 1 .
Série: Integrated Accrocher le panneau aux dispositifs de Àxation en insérant dans les crans d’alignement supérieurs 6 . 6 Il est possible d’ajuster l’alignement du panneau par rapport aux meubles adjacents à l’aide des pattes et des équerres d’alignement 7 et 8 . 7 Alignement vertical: soulever ou abaisser le panneau 9 en vissant ou en dévissant la vis à l’équerre.
Notice d’Installation Série: tous IMPORTANT: Les instructions suivantes pour l’installation s’appliquent à tous les modèles Fhiaba. Installation dans la niche Encastrement appareil unique 1 Des proÀls en aluminium peuvent être utilisés pour fermer les espaces entre l’appareil et les meubles adjacents ou un autre appareil juxtaposé à celui-ci.
Série: tous Encastrement combinaison 1 Accessoires nécessaires à commander séparément: Kit raccordement central (KCCIT/KCCIH) Des proÀls en aluminium peuvent être utilisés pour fermer les espaces entre l’appareil et les meubles adjacents ou un autre appareil juxtaposé à celui-ci. Intervenir de la manière suivante: Positionner les appareils devant la niche en laissant un espace sufÀsant pour intervenir sur l’arrière des appareils 1 .
Notice d’Installation Série: tous Une fois complétés les passages ci-dessus, poussez les appareils dans leur position déÀnitive 6 . Il sera nécessaire de prévoir une cheminée de ventilation à l’arrière de la niche pour garantir une ventilation adèquate. Un écart de 5 mm est sufÀsant pour éviter tout surchauffement. Assemblez toujours les panneaux frontaux à la porte et aux tiroirs avant de placer l’appareil dans sa position déÀnitive dans la niche ou la structure.
Série: Integrated Montage de la sécurité anti-renversement 1 5⁄8” ) 59 (2 3⁄8”) 45 ( 152 AÀn d’éviter le risque de renversement de l’appareil lors de l’ouverture de la porte et des bacs à pleine charge, l’installation de deux équerres qui Àxent la partie supérieure de l’appareil au mur est obligatoire. (6”) Intervenir de la manière suivante: 1 Les équerres sont appliquées comme illustré à la Àgure en utilisant les vis et les chevilles fournies.
Notice d’Installation Série: StandPlus/X-Pro Montage de la sécurité anti-renversement AÀn d’éviter le risque de renversement de l’appareil lors de l’ouverture de la porte et des bacs à pleine charge, l’installation de deux équerres qui Àxent la partie supérieure de l’appareil au mur est obligatoire. Intervenir de la manière suivante: Les équerres sont appliquées comme illustré à la Àgure en utilisant les vis et les chevilles fournies.
Série: StandPlus/X-Pro Montage des poignées sur le devant inoxydable 1 Pour Àxer les poignées à la porte et au grand bac, intervenir comme indiqué. Intervenir de la manière suivante: Insérer les écarteurs sur les deux goujons présents sur la porte et sur le grand bac 1 . Visser les vis à six pans présentes dans la poignée 2 . 2 Les vis de Àxation seront serrées à fond, en utilisant une clé à six pans de 2,5 mm (1/8”). 30 www.fhiaba.com · www.thevettagroup.
Notice d’Installation Série: Integrated Circulation de l’air A Série 36 Série 30 Série 24 860 (33 7⁄8”) 740 (29 1⁄8”) 560 (22”) B > 100 (4”) C 10 (3⁄8”) 50% C B C A www.fhiaba.com · www.thevettagroup.com 31 Français English Un système à air forcé assure la ventilation à travers la grille positionnée dans la dans la partie inférieure de l’appareil.
Série: StandPlus/X-Pro Ventilation La ventilation est garantie par un système à air forcé à travers une grille positionnée dans la partie haute de l’appareil. Cette grille ne doit en aucun cas être couverte par des panneaux ou autres dispositifs qui pourraient en réduire l’efÀcacité. S’il vous plaît se référer à la page 5-6 pour assurer une circulation d’air correcte. 32 www.fhiaba.com · www.thevettagroup.
Notice d’Installation Série: tous Contrôle de Àn d’installation mise en marche Contrôler que les pieds sont correctement installés. Contrôler que le raccordement à l’installation hydrique ne présente pas de fuites d’eau et que le robinet de fermeture est facilement accessible. Contrôler que le branchement électrique soit correctement réalisé et que la Àche et l’interrupteur omnipolaire dédié soient facilement accessibles. Contrôler le parfait alignement de l’appareil avec les meubles adjacents.
Série: tous Mise en marche Pour mettre en marche l’appareil, brancher la Àche au réseau électrique: lorsque la porte est ouverte, apparaît sur le panneau de commande le message “Stand-by”, alors que toutes les touches du panneau sont éteintes. UNIT Before starting Before starting Electronic Control UNIT FRIDGE 1 2 3 Unit 4 5 6 ENTER ICE MAKER 7 8 9 Switches the appliance (all compartments) between ON and STAND BY (press for three seconds).
27-11-2014 EN Fhiaba srl is constantly researching new way to improve the features and the design of their products, therefore models are often upgraded and reviewed. FR Fhiaba est constamment à la recherche de nouvelles solutions pour améliorer les caractéristiques et le design de ses propres produits et se réserve le droit d’apporter continuellement des modiÀcations à ses modèles.
B09000704 UL www. f hi a b a . c o m Info Line 800 - Fhiaba .